Nissan Sentra (2019 year). Instruction — part 25
PASSENGER COMPARTMENT
WARNING
Never use a fuse of higher or lower am-
perage rating than that specified on the
fuse box cover. This could damage the
electrical system or electronic control
units or cause a fire.
If any electrical equipment does not oper-
ate, check for an open fuse.
NOTE:
The fuse box is located on the driver’s
side of the instrument panel.
1. Be sure the ignition switch and the
headlight switch are OFF.
2. Remove the fuse box cover
䊊
A
with a
suitable tool. Use a cloth to avoid dam-
aging the trim.
3. Locate the fuse that needs to be re-
placed.
4. Remove the fuse with the fuse puller
䊊
B
.
5. If the fuse is open
䊊
C
, replace it with an
equivalent good fuse
䊊
D
.
6. Push the fuse box cover to install.
If a new fuse also opens, have the electrical
system checked and repaired. It is recom-
mended that you visit a NISSAN dealer for
this service.
NOTE:
Your vehicle may not be equipped with
all fuses listed on the fuse label.
LDI2712
LDI2713
8-24
Do-it-yourself
Extended storage switch
If any electrical equipment does not oper-
ate, remove the extended storage switch
and check for an open fuse.
NOTE:
The extended storage switch is used for
long term vehicle storage. Even if the ex-
tended storage switch is broken it is not
necessary to replace it. Replace only the
open fuse in the switch with a new fuse.
How to replace the extended storage
switch:
1. To
remove
the
extended
storage
switch, be sure the ignition switch is in
the OFF or LOCK position.
2. Be sure the headlight switch is in the
OFF position.
3. Remove the fuse box cover.
4. Pinch the locking tabs
䊊
A
and
䊊
B
found
on each side of the storage switch.
5. Pull the storage switch straight out
from the fuse box
䊊
C
.
CAUTION
Be careful not to allow children to swal-
low the battery or removed parts.
LDI2747
BATTERY REPLACEMENT
Do-it-yourself
8-25
KEY FOB (if so equipped)
Replace the battery in the key fob as fol-
lows:
1. Remove the screw
䊊
A
.
2. Insert a small screwdriver into the slit of
the corner
䊊
B
and twist it to separate
the upper part from the lower part. Use
a cloth to protect the casing.
3. Replace the battery with a new one.
∙ Do not touch the internal circuit and
electric terminals as doing so could
cause a malfunction.
∙ Make sure that the + side faces the
bottom of the case
䊊
C
.
Recommended battery: CR1620 or equiva-
lent.
4. Close the lid and install the screw se-
curely.
5. Operate the buttons to check its op-
eration.
If you need assistance with replacement, it
is recommended that you visit a NISSAN
dealer for this service.
If the battery is removed for any reason
other than replacement, perform step 5.
∙ An improperly disposed battery can
hurt the environment. Always con-
firm local regulations for battery dis-
posal.
∙ The key fob is water-resistant; how-
ever, if it does get wet, immediately
wipe completely dry.
∙ The operational range of the key fob
extends to approximately 33 ft (10 m)
from the vehicle. This range may vary
with conditions.
Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device
must accept any interference received,
including interference that may cause
undesired operation of the device.
FCC Notice:
For USA:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the fol-
lowing two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any interfer-
ence received, including interference
that may cause undesired operation.
Note:
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s author-
ity to operate the equipment.
LDI2219
8-26
Do-it-yourself
For Canada:
This
devise
complies
with
Industry
Canada licence-exempt RSS standard(s).
Operation is subject to the following two
conditions: (1) this device may not cause
interference, and (2) this device must ac-
cept any interference, including interfer-
ence that may cause undesired opera-
tion of the device.
NISSAN INTELLIGENT KEY® (if so
equipped)
Replace the battery in the Intelligent Key as
follows:
1. Remove the mechanical key from the
Intelligent Key.
2. Insert a small flathead screwdriver
䊊
A
into the slit
䊊
B
of the corner and twist it
to separate the upper part from the
lower part. Place a cloth over the
screwdriver to protect the casing.
LDI2001
Do-it-yourself
8-27
3. Replace the battery with a new one.
Recommended battery: CR2025 or
equivalent.
∙ Do not touch the internal circuit and
electric terminals as doing so could
cause a malfunction.
∙ Hold the battery by the edges. Hold-
ing the battery across the contact
points will seriously deplete the stor-
age capacity.
∙ Make sure that the + side faces the
bottom of the lower part.
4. Close the lid securely as illustrated with
䊊
C
and
䊊
D
.
5. Operate the buttons to check the op-
eration.
If you need assistance with replacement, it
is recommended that you visit a NISSAN
dealer for this service.
FCC Notice:
For USA:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the fol-
lowing two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any interfer-
ence received, including interference
that may cause undesired operation.
Note:
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s author-
ity to operate the equipment.
For Canada:
This
device
complies
with
Industry
Canada licence-exempt RSS standard(s).
Operation is subject to the following two
conditions: (1) this device may not cause
interference, and (2) this device must ac-
cept any interference, including interfer-
ence that may cause undesired opera-
tion of the device.
LDI2637
8-28
Do-it-yourself
HEADLIGHTS
For additional information on headlight
bulb replacement, refer to the instructions
outlined in this section.
Replacing the halogen headlight
bulb (if so equipped)
NOTE:
The headlight is a semi-sealed beam type
which used a replaceable headlight (halo-
gen) bulb. They can be replaced from in-
side the engine compartment without re-
moving the headlight assembly.
CAUTION
∙ Aiming is not necessary after replac-
ing the bulb. When aiming adjustment
is necessary, it is recommended that
you visit a NISSAN dealer for this
service.
∙ Do not leave the headlight assembly
open without a bulb installed for a
long period of time. Dust, moisture,
smoke, etc. entering the headlight
body may affect bulb performance.
Remove the bulb from the headlight
assembly just before a replacement
bulb is installed.
∙ Only touch the base when handling
the bulb. Never touch the glass enve-
lope. Touching the glass could signifi-
cantly affect bulb life and/or head-
light performance.
∙ High pressure halogen gas is sealed
inside the halogen bulb. The bulb may
break
if
the
glass
envelope
is
scratched or the bulb is dropped.
∙ Use the same number and wattage as
shown in the chart.
Type A (if so equipped)
LDI2980
LIGHTS
Do-it-yourself
8-29
1. Rotate the (high beam) cover
䊊
A
coun-
terclockwise to access the (high beam)
bulb socket
䊊
C
. Rotate the bulb socket
䊊
C
counterclockwise and remove bulb.
2. Rotate the (low beam) cover
䊊
B
(if so
equipped) counterclockwise to access
the (low beam) bulb socket
䊊
D
(if so
equipped). Rotate the bulb socket
䊊
D
(if
so equipped) counterclockwise and re-
move bulb.
3. Rotate the side marker bulb socket
䊊
E
counterclockwise and remove bulb.
4. Rotate the turn signal bulb socket
䊊
F
counterclockwise and remove bulb
䊊
G
.
Reverse instructions to install bulbs and
replace fender protector.
WARNING
Do not touch bulb by hand while it is lit
or right after being turned off. Burning
may result.
CAUTION
• Do not touch glass surface of the bulb
with bare hands or allow oil or grease to
get on it to prevent damage to bulb.
• Do not leave the bulb out of the lamp
reflector for a long time because dust,
moisture, smoke, etc. may affect the
performance of the lamp.
• Fog may temporarily form inside the
lens of the exterior lights in the rain or in
a car wash. A temperature difference
between the inside and the outside of
the lens causes the fog. This is not a
malfunction. If large drops of water col-
lect inside the lens, it is recommended
that you visit a NISSAN dealer for
servicing.
Replacing the LED headlight bulb
(if so equipped)
If LED headlight bulb replacement is re-
quired, it is recommended that you visit a
NISSAN dealer for this service.
TURN SIGNAL BULB
To replace the turn signal bulb follow the
instructions listed in the “Replacing the
halogen headlight bulb” found in this sec-
tion.
FOG LIGHTS (if so equipped)
For additional information on fog light bulb
replacement, refer to the instructions out-
lined in this section.
Type B (if so equipped)
LDI2981
8-30
Do-it-yourself
Replacing the fog light bulb
CAUTION
∙ High pressure halogen gas is sealed
inside the halogen bulb. The bulb may
break
if
the
glass
envelope
is
scratched or the bulb is dropped.
∙ When handling the bulb, do not touch
the glass envelope.
∙ Use the same number and wattage as
originally installed as shown in the
chart.
∙ Do not leave the bulb out of the fog
light for a long period of time as dust,
moisture and smoke may enter the
fog light body and affect the perfor-
mance of the fog light.
1. Disconnect the negative battery cable.
2. Access to the fog light is in front of and
behind the front tire and the fascia.
3. Remove the fasteners
䊊
A
; carefully pull
back the front fender protector.
4. Rotate the bulb
䊊
B
counterclockwise
and pull out to remove.
LDI2935
Do-it-yourself
8-31
5. Remove by pulling straight off the fog
light. Do not shake or rotate the bulb
when removing it.
6. Install the new bulb in the reverse order
of removal.
EXTERIOR AND INTERIOR LIGHTS
Item
Wattage (W)
Bulb No.
Headlight assembly (Type A) (if so equipped)
Low/Daytime running (Canada only)
55
H11
High
65
H9
Turn/Park
27/7
3157 AK
Side marker
5
W5W
Headlight assembly (Type B) (if so equipped)
Low/Daytime running (Canada only)
—
—
High**
65/—
H9/—
Turn/Park
27/7
3157 AK
Park
—
—
Side marker
5
W5W
Daytime running lights (NISMO models only)
—
—
Front fog light (if so equipped)
55
H11
Door mirror turn signal light (if so equipped)*
—
—
Vanity mirror light (if so equipped)*
—
—
Map lights*
—
—
Room light*
8
—
Trunk light*
3.4
158
High-mounted stop light*
Inside (if so equipped)
—
—
Spoiler (if so equipped)
—
—
Rear combination light*
Turn
21
WY21W
Tail
—
—
Stop/Tail
21/5
W21/5W
Backup (reversing)
16
W16W
Side marker
—
—
License plate light*
5
W5W
Always check with the Parts Department at a NISSAN dealer for the latest parts information.
* It is recommended that you visit a NISSAN dealer for replacement.
** Headlight assembly (Type B) (if so equipped) uses the projector LED and the H9 bulb for
the high beam function.
8-32
Do-it-yourself
1.
Map light
2.
Room light
3.
Door mirror turn signal light (if so
equipped)
4.
Headlight assembly
5.
Fog light (if so equipped)/ Daytime
running light (NISMO models only)
6.
High-mount stop light (inside)(if so
equipped)
7.
Trunk light
8.
High-mount stop light (spoiler)(if so
equipped)
9.
License plate light
10.
Rear combination light
Replacement procedures
All other lights are either type A, B, C or D.
When replacing a bulb, first remove the
lens, lamp and/or cover.
Indicates bulb removal
Indicates bulb installation
LDI3137
WDI0263
Do-it-yourself
8-33
If you have a flat tire, refer to “Flat tire” in
the “In case of emergency” section of
this manual.
TIRE PRESSURE
Tire Pressure Monitoring System
(TPMS)
WARNING
Radio waves could adversely af-
fect electric medical equipment.
Those who use a pacemaker
should contact the electric medi-
cal equipment manufacturer for
the possible influences before
use.
This vehicle is equipped with the Tire
Pressure Monitoring System (TPMS).
It monitors tire pressure of all tires
except the spare. When the low tire
pressure warning light is lit and the
CHECK TIRE PRES (vehicles without a
vehicle information display) warning
is displayed in the odometer, or the
“Tire Pressure Low — Add Air” (ve-
hicles with a vehicle information dis-
play) appears in the vehicle informa-
tion display, one or more of your tires
is significantly under-inflated.
The TPMS will activate only when the
vehicle is driven at speeds above
16 mph (25 km/h). Also, this system
may not detect a sudden drop in tire
pressure (for example a flat tire while
driving).
For additional information, refer to
“Low tire pressure warning light” in
the “Instruments and controls” sec-
tion, “Tire Pressure Monitoring Sys-
tem (TPMS)” in the “Starting and driv-
ing” section, and “Flat tire” in the “In
case of emergency” section of this
manual.
Tire inflation pressure
Check the tire pressures (including
the spare) often and always prior to
long distance trips. The recom-
mended tire pressure specifications
are shown on the F.M.V.S.S./C.M.V.S.S.
certification label or the Tire and
Loading Information label under the
“Cold Tire Pressure” heading. The Tire
and Loading Information label is af-
fixed to the driver side center pillar.
Tire pressures should be checked
regularly because:
∙ Most tires naturally lose air over
time.
∙ Tires can lose air suddenly when
driven over potholes or other ob-
jects or if the vehicle strikes a
curb while parking.
The
tire
pressures
should
be
checked when the tires are cold. The
tires are considered COLD after the
vehicle has been parked for 3 or
more hours, or driven less than 1 mile
(1.6 km) at moderate speeds.
The TPMS with Easy-Fill Tire Alert (if
so equipped) provides visual and au-
dible signals outside the vehicle for
inflating tires to the recommended
COLD tire pressure. For additional in-
formation, refer to “TPMS with Easy-
Fill Tire Alert” in the “Starting and driv-
ing” section of this manual.
WHEELS AND TIRES
8-34
Do-it-yourself
Incorrect tire pressure, including
under inflation, may adversely af-
fect tire life and vehicle handling.
WARNING
∙ Improperly inflated tires can fail
suddenly
and
cause
an
accident.
∙ The Gross Vehicle Weight Rating
(GVWR)
is
located
on
the
F.M.V.S.S./C.M.V.S.S.
certifica-
tion label. The vehicle weight
capacity is indicated on the Tire
and Loading Information label.
Do not load your vehicle beyond
this capacity. Overloading your
vehicle may result in reduced
tire life, unsafe operating condi-
tions due to premature tire fail-
ure, or unfavorable handling
characteristics and could also
lead to a serious accident. Load-
ing beyond the specified capac-
ity may also result in failure of
other vehicle components.
∙ Before taking a long trip, or
whenever you heavily load your
vehicle, use
a
tire
pressure
gauge to ensure that the tire
pressures are at the specified
level.
∙ For additional information re-
garding tires, refer to “Impor-
tant Tire Safety Information”
(US) or “Tire Safety Information”
(Canada) in the Warranty Infor-
mation Booklet.
Do-it-yourself
8-35
Tire and Loading Information
label
䊊
1
Seating capacity: The maximum
number of occupants that can
be seated in the vehicle.
䊊
2
Vehicle load limit: Refer to “Ve-
hicle loading information” in the
“Technical and consumer infor-
mation” section of this manual.
䊊
3
Original tire size: The size of the
tires originally installed on the
vehicle at the factory.
䊊
4
Cold tire pressure: Inflate the
tires to this pressure when the
tires are cold. Tires are consid-
ered COLD after the vehicle has
been parked for 3 or more hours,
or driven less than 1 mile (1.6 km)
at moderate speeds. The rec-
ommended cold tire inflation is
set by the manufacturer to pro-
vide the best balance of tire
wear, vehicle handling, driveabil-
ity, tire noise, etc., up to the vehi-
cle’s GVWR.
䊊
5
Tire size: Refer to “Tire labeling” in
this section.
䊊
6
Spare tire size.
LDI2007
8-36
Do-it-yourself
Checking tire pressure
1. Remove the valve stem cap from
the tire.
2. Press
the
pressure
gauge
squarely onto the valve stem. Do
not press too hard or force the
valve stem sideways, or air will
escape. If the hissing sound of air
escaping from the tire is heard
while checking the pressure, re-
position the gauge to eliminate
this leakage.
3. Remove the gauge.
4. Read the tire pressure on the
gauge stem and compare to the
specification shown on the Tire
and Loading Information label.
5. Add air to the tire as needed. If
too much air is added, press the
core of the valve stem briefly
with the tip of the gauge stem to
release pressure. Recheck the
pressure and add or release air
as needed.
6. Install the valve stem cap.
7. Check the pressure of all other
tires, including the spare.
Grades: NISMO
Size
Cold Tire Infla-
tion Pressure
Front Original
Tire:
215/45ZR18
230 kPa, 33 PSI
Grades: NISMO
Rear Original
Tire:
215/45ZR18
230 kPa, 33 PSI
Spare Tire:
T125/70D16
420 kPa, 60 PSI
Grades: S, SV, SR, SL
Size
Cold Tire Infla-
tion Pressure
Front Original
Tire:
205/50R17
P205/55R16
230 kPa, 33 PSI
Rear Original
Tire:
205/50R17
P205/55R16
230 kPa, 33 PSI
Spare Tire:
T125/70D16
420 kPa, 60 PSI
LDI0393
Do-it-yourself
8-37
TIRE LABELING
Federal law requires tire manufac-
turers to place standardized infor-
mation on the sidewall of all tires.
This information identifies and de-
scribes the fundamental character-
istics of the tire and also provides the
Tire Identification Number (TIN) for
safety standard certification. The TIN
can be used to identify the tire in
case of a recall.
䊊
1
Tire size (example: P215/65R15
95H)
1. P: The “P” indicates the tire is de-
signed for passenger vehicles
(not all tires have this informa-
tion).
2. Three-digit number (215): This
number gives the width in milli-
meters of the tire from sidewall
edge to sidewall edge.
3. Two-digit
number
(65):
This
number, known as the aspect
ratio, gives the tire’s ratio of
height to width.
4. R: The “R” stands for radial.
5. Two-digit number (15): This num-
ber is the wheel or rim diameter
in inches.
Example
WDI0394
Example
WDI0395
8-38
Do-it-yourself
6. Two- or three-digit number (95):
This number is the tire’s load in-
dex. It is a measurement of how
much weight each tire can sup-
port. You may not find this infor-
mation on all tires because it is
not required by law.
7. H: Tire speed rating. You should
not drive the vehicle faster than
the tire speed rating.
䊊
2
TIN (Tire Identification Number)
for a new tire (example: DOT XX XX
XXX XXXX)
1. DOT: Abbreviation for the “De-
partment
Of
Transportation”.
The
symbol
can
be
placed
above, below or to the left or
right of the Tire Identification
Number.
2. Two-digit code: Manufacturer’s
identification mark.
3. Two-digit code: Tire size.
4. Three-digit code: Tire type code
(Optional).
5. Four numbers represent the
week and year the tire was built.
For example, the numbers 3103
means the 31st week of 2003. If
these numbers are missing then
look on the other sidewall of the
tire.
Example
LDI2786
Do-it-yourself
8-39
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст