Qashqai J11. Exterior Lighting system — part 9
STOP LAMP CIRCUIT
EXL-129
< DTC/CIRCUIT DIAGNOSIS >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
2.
Connect BCM connector.
3.
Turn ignition switch ON.
4.
Check voltage between stop lamp switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
CHECK STOP LAMP SWITCH SIGNAL CIRCUIT (OPEN)
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check continuity between BCM harness connector and stop lamp switch harness connector.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
6.
CHECK STOP LAMP SWITCH
Check stop lamp switch. Refer to
EXL-131, "Component Inspection"
.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-132, "Removal and Installation"
.
NO
>> Replace stop lamp switch. Refer to
(LHD models) or
(RHD models).
7.
CHECK STOP LAMP / HIGH-MOUNTED STOP LAMP OUTPUT VOLTAGE
With CONSULT
1.
Disconnect stop lamp / tail lamp (body side) connectors.
2.
Turn ignition switch ON.
3.
Select “HEAD LAMP” of “BCM” using CONSULT.
4.
Select “STOP LAMP 1”, “STOP LAMP 2” or “STOP LAMP 3” in “Active Test” mode.
5.
With operating the test items, check voltage between BCM harness connector and ground.
Stop lamp RH
Stop lamp LH
+
-
Voltage
Stop lamp switch
Connector
Terminal
E50
1
Ground
9 – 16 V
BCM
Stop lamp switch
Continuity
Connector
Terminal
Connector
Terminal
E60
157
E50
2
Existed
+
-
Test item
Voltage
(Approx.)
BCM
Connector
Terminal
B3
134
Ground
STOP LAMP 1
On
9 – 16 V
Off
0 V
+
-
Test item
Voltage
(Approx.)
BCM
Connector
Terminal
B3
129
Ground
STOP LAMP 2
On
9 – 16 V
Off
0 V
EXL-130
< DTC/CIRCUIT DIAGNOSIS >
[LED HEADLAMP]
STOP LAMP CIRCUIT
High-mounted stop lamp
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> GO TO 8.
8.
CHECK STOP LAMP / HIGH-MOUNTED STOP LAMP POWER SUPPLY CIRCUIT (SHORT)
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check continuity between BCM harness connector and ground.
Stop lamp
High-mounted stop lamp
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-132, "Removal and Installation"
.
NO
>> Repair or replace harness.
9.
CHECK STOP LAMP / HIGH-MOUNTED STOP LAMP POWER SUPPLY CIRCUIT (OPEN)
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check continuity between BCM harness connector and each stop lamp harness connector.
Stop lamp
High-mounted stop lamp
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> Repair or replace harness.
10.
CHECK STOP LAMP / HIGH-MOUNTED STOP LAMP GROUND CIRCUIT
Check continuity between each stop lamp harness connector and ground.
+
-
Test item
Voltage
(Approx.)
BCM
Connector
Terminal
B4
39
Ground
STOP LAMP 3
On
9 – 16 V
Off
0 V
BCM
—
Continuity
Connector
Terminal
RH
B3
134
Ground
Not existed
LH
129
BCM
—
Continuity
Connector
Terminal
B4
39
Ground
Not existed
BCM
Stop lamp / tail lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
B3
134
B79
1
Existed
LH
129
B22
BCM
High-mounted stop lamp
Continuity
Connector
Terminal
Connector
Terminal
B4
39
B17
2
Existed
STOP LAMP CIRCUIT
EXL-131
< DTC/CIRCUIT DIAGNOSIS >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Stop lamp
High-mounted stop lamp
Is the inspection result normal?
YES-1 >> Stop lamp: Replace the corresponding rear combination lamp. Refer to
YES-2 >> High-mounted stop lamp: Replace high-mounted stop lamp. Refer to
NO
>> Repair or replace harness.
Component Inspection
INFOID:0000000010338819
1.
CHECK STOP LAMP SWITCH-1
1.
Turn ignition switch OFF.
2.
Disconnect stop lamp switch connector.
3.
Check continuity of stop lamp switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK STOP LAMP SWITCH-2
1.
Adjust stop lamp switch installation. Refer to
BR-8, "Inspection and Adjustment"
(RHD models).
2.
Check continuity of stop lamp switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace stop lamp switch. Refer to
(LHD models) or
(RHD models).
Stop lamp / tail lamp
—
Continuity
Connector
Terminal
RH
B79
2
Ground
Existed
LH
B22
High-mounted stop lamp
—
Continuity
Connector
Terminal
B17
3
Ground
Existed
Stop lamp switch
Condition
Continuity
Terminal
1
2
Brake pedal
Depressed
Existed
Fully released
Not existed
Stop lamp switch
Condition
Continuity
Terminal
1
2
Brake pedal
Depressed
Existed
Fully released
Not existed
EXL-132
< DTC/CIRCUIT DIAGNOSIS >
[LED HEADLAMP]
FRONT FOG LAMP CIRCUIT
FRONT FOG LAMP CIRCUIT
Component Function Check
INFOID:0000000010338823
1.
CHECK FRONT FOG LAMP OPERATION
With CONSULT
1.
Select “FRONT FOG LAMP” in “Active Test” mode of “IPDM E/R” using CONSULT.
2.
With operating the test items, check that the front fog lamp is turned ON.
Is the inspection result normal?
YES
>> Front fog lamp circuit is normal.
NO
>> Refer to
EXL-132, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000010338824
1.
CHECK FRONT FOG LAMP OUTPUT VOLTAGE
With CONSULT
1.
Turn ignition switch OFF.
2.
Disconnect front fog lamp connector.
3.
Turn ignition switch ON.
4.
Select “FRONT FOG LAMP” in “Active Test” mode of “IPDM E/R” using CONSULT.
5.
With operating the test items, check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace IPDM E/R. Refer to
PCS-67, "Removal and Installation"
2.
CHECK FRONT FOG LAMP POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and front fog lamp harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK FRONT FOG LAMP GROUND CIRCUIT
Check continuity between front fog lamp harness connector and ground.
On
: Front fog lamp ON
Off
: Front fog lamp OFF
+
-
Test item
Voltage
IPDM E/R
Connector
Terminal
RH
E101
49
Ground
FRONT FOG
LAMP
On
9 – 16 V
Off
0 – 1 V
LH
E102
59
On
9 – 16 V
Off
0 – 1 V
IPDM E/R
Front fog lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E101
49
E95
1
Existed
LH
E102
59
E94
FRONT FOG LAMP CIRCUIT
EXL-133
< DTC/CIRCUIT DIAGNOSIS >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Is the inspection result normal?
YES
>> Replace the corresponding front fog lamp bulb. Refer to
NO
>> Repair or replace harness.
Front fog lamp
—
Continuity
Connector
Terminal
RH
E95
2
Ground
Existed
LH
E94
EXL-134
< DTC/CIRCUIT DIAGNOSIS >
[LED HEADLAMP]
REAR FOG LAMP CIRCUIT
REAR FOG LAMP CIRCUIT
Component Function Check
INFOID:0000000010338825
1.
CHECK REAR FOG LAMP OPERATION
With CONSULT
1.
Select “HEAD LAMP” of “BCM” using CONSULT.
2.
Select “RR FOG LAMP” in “Active Test” mode.
3.
With operating the test items, check that the rear fog lamp is turned ON.
Is the inspection result normal?
YES
>> Rear fog lamp circuit is normal.
NO
>> Refer to
EXL-134, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000010338826
1.
CHECK REAR FOG LAMP OUTPUT VOLTAGE
With CONSULT
1.
Turn ignition switch OFF.
2.
Disconnect rear fog lamp connector.
3.
Turn ignition switch ON.
4.
Select “HEAD LAMP” of “BCM” using CONSULT.
5.
Select “RR FOG LAMP” in “Active Test” mode.
6.
With operating the test items, check voltage between rear fog lamp harness connector and ground.
LHD models
RHD models
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 2.
2.
CHECK REAR FOG LAMP POWER SUPPLY CIRCUIT (OPEN)
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check continuity between BCM harness connector and rear fog lamp harness connector.
LHD models
On
: Rear fog lamp ON
Off
: Rear fog lamp OFF
+
-
Test item
Voltage
Rear fog lamp
Connector
Terminal
B24
1
Ground
RR FOG LAMP
On
9 – 16 V
Off
0 V
+
-
Test item
Voltage
Rear fog lamp
Connector
Terminal
D83
1
Ground
RR FOG LAMP
On
9 – 16 V
Off
0 V
BCM
Rear fog lamp
Continuity
Connector
Terminal
Connector
Terminal
B3
122
B24
1
Existed
REAR FOG LAMP CIRCUIT
EXL-135
< DTC/CIRCUIT DIAGNOSIS >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
RHD models
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK REAR FOG LAMP POWER SUPPLY CIRCUIT (SHORT)
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-132, "Removal and Installation"
.
NO
>> Repair or replace harness.
4.
CHECK REAR FOG LAMP GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between rear fog lamp harness connector and ground.
LHD models
LHD models
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
CHECK REAR FOG LAMP BULB
Check rear fog lamp bulb.
Is the inspection result normal?
YES
>> Check rear fog lamp bulb socket. Repair or replace if necessary.
NO
>> Replace rear fog lamp bulb. Refer to
.
BCM
Rear fog lamp
Continuity
Connector
Terminal
Connector
Terminal
B3
122
D83
1
Existed
BCM
—
Continuity
Connector
Terminal
B3
122
Ground
Not existed
Rear fog lamp
—
Continuity
Connector
Terminal
B24
2
Ground
Existed
Rear fog lamp
—
Continuity
Connector
Terminal
D83
2
Ground
Existed
EXL-136
< DTC/CIRCUIT DIAGNOSIS >
[LED HEADLAMP]
TURN SIGNAL LAMP CIRCUIT
TURN SIGNAL LAMP CIRCUIT
Component Function Check
INFOID:0000000010338828
1.
CHECK TURN SIGNAL LAMP OPERATION
1.
Turn ignition switch ON.
2.
With operating the turn signal switch, check that the turn signal lamp is blinks.
Is the inspection result normal?
YES
>> Turn signal lamp circuit is normal.
NO
>> Refer to
EXL-136, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000010338829
1.
CHECK SYMPTOM
Check symptom (A or B)
Which symptom is detected?
A
>> GO TO 2.
B
>> GO TO 4.
2.
CHECK FUSE
1.
Turn ignition switch OFF.
2.
Check that the following fuse is not fusing.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace the blown fuse after repairing the affected circuit if a fuse is blown.
3.
CHECK BCM POWER SUPPLY (TURN SIGNAL LAMP)
1.
Disconnect BCM connector.
2.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-132, "Removal and Installation"
.
NO
>> Repair or replace harness.
4.
CHECK TURN SIGNAL LAMP OUTPUT VOLTAGE
1.
Turn ignition switch OFF.
2.
Disconnect the following connectors.
-
Front combination lamp
Right
: Turn signal lamps RH blink
Left
: Turn signal lamps LH blink
Center
: Turn signal lamps OFF
Symptom
A
All of turn signal lamp are not blinks
B
Applicable side performs high flasher activation
Unit
Location
Fuse No.
Capacity
BCM
Fuse block (J/B)
#33
10 A
+
-
Voltage
BCM
Connector
Terminal
M68
144
Ground
9 – 16 V
TURN SIGNAL LAMP CIRCUIT
EXL-137
< DTC/CIRCUIT DIAGNOSIS >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
-
Door mirror
-
Rear turn signal lamp
3.
Turn ignition switch ON.
4.
With operating the turn signal switch, check voltage between BCM harness connector and ground.
Front turn signal lamp
Side turn signal lamp
+
-
Test item
Voltage
(Approx.)
BCM
Connector
Terminal
RH
E60
168
Ground
Turn signal
switch
Right
Center
0 V
LH
167
Left
Center
0 V
+
-
Test item
Voltage
(Approx.)
BCM
Connector
Terminal
RH
M70
43
Ground
Turn signal
switch
Right
Center
0 V
LH
42
Left
Center
0 V
PKID0926E
PKID0926E
PKID0926E
PKID0926E
EXL-138
< DTC/CIRCUIT DIAGNOSIS >
[LED HEADLAMP]
TURN SIGNAL LAMP CIRCUIT
Rear turn signal lamp
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> GO TO 5.
5.
CHECK TURN SIGNAL LAMP POWER SUPPLY CIRCUIT (SHORT)
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check continuity between BCM harness connector and ground.
Front turn signal lamp
Side turn signal lamp
Rear turn signal lamp
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-132, "Removal and Installation"
.
NO
>> Repair or replace harness.
6.
CHECK TURN SIGNAL LAMP POWER SUPPLY CIRCUIT (OPEN)
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
+
-
Test item
Voltage
(Approx.)
BCM
Connector
Terminal
RH
B3
136
Ground
Turn signal
switch
Right
Center
0 V
LH
133
Left
Center
0 V
PKID0926E
PKID0926E
BCM
—
Continuity
Connector
Terminal
RH
E60
168
Ground
Not existed
LH
167
BCM
—
Continuity
Connector
Terminal
RH
M70
43
Ground
Not existed
LH
42
BCM
—
Continuity
Connector
Terminal
RH
B3
136
Ground
Not existed
LH
133
TURN SIGNAL LAMP CIRCUIT
EXL-139
< DTC/CIRCUIT DIAGNOSIS >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
3.
Check continuity between BCM harness connector and each turn signal lamp harness connector.
Front turn signal lamp
Side turn signal lamp (LHD models)
Side turn signal lamp (RHD models)
Rear turn signal lamp
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace harness.
7.
CHECK TURN SIGNAL LAMP GROUND CIRCUIT
Check continuity between each turn signal lamp harness connector and ground.
Front turn signal lamp
Side turn signal lamp (LHD models)
Side turn signal lamp (RHD models)
BCM
Front combination lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E60
168
E93
8
Existed
LH
167
E91
BCM
Door mirror
Continuity
Connector
Terminal
Connector
Terminal
RH
M70
43
D27
13
Existed
LH
42
D3
BCM
Door mirror
Continuity
Connector
Terminal
Connector
Terminal
RH
M70
43
D40
13
Existed
LH
42
D16
BCM
Rear turn signal lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
B3
136
B80
1
Existed
LH
133
B23
Front combination lamp
—
Continuity
Connector
Terminal
RH
E93
6
Ground
Existed
LH
E91
Door mirror
—
Continuity
Connector
Terminal
RH
D27
14
Ground
Existed
LH
D3
Door mirror
—
Continuity
Connector
Terminal
RH
D40
14
Ground
Existed
LH
D16
EXL-140
< DTC/CIRCUIT DIAGNOSIS >
[LED HEADLAMP]
TURN SIGNAL LAMP CIRCUIT
Rear turn signal lamp
Is the inspection result normal?
YES-1 >> Front turn signal lamp or rear turn signal lamp: GO TO 8.
YES-2 >> Side turn signal lamp: Replace side turn signal lamp. Refer to
EXL-166, "Removal and Installa-
.
NO
>> Repair or replace harness.
8.
CHECK TURN SIGNAL LAMP BULB
Check the applicable turn signal lamp bulb.
Is the inspection result normal?
YES
>> Check the corresponding turn signal lamp bulb socket. Repair or replace if necessary.
NO
>> Replace the corresponding turn signal lamp bulb. Refer to
signal lamp) or
(rear turn signal lamp).
Rear turn signal lamp
—
Continuity
Connector
Terminal
RH
B80
2
Ground
Existed
LH
B23
LIGHT & RAIN SENSOR
EXL-141
< DTC/CIRCUIT DIAGNOSIS >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
LIGHT & RAIN SENSOR
Component Function Check
INFOID:0000000010452494
1.
CHECK LIGHT & RAIN SENSOR
1.
Clean light & rain sensor detection area of windshield fully.
2.
Turn ignition switch ON.
3.
Turn lighting switch AUTO.
4.
With the light & rain sensor illuminating, check the auto light function.
Is the inspection result normal?
YES
>> Light & rain sensor is normal.
NO
>> Refer to
EXL-141, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000010452495
1.
CHECK LIGHT & RAIN SENSOR POWER SUPPLY
1.
Turn ignition switch OFF
2.
Disconnect light & rain sensor connector.
3.
Turn ignition switch ON.
4.
Check voltage between light & rain sensor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK LIGHT & RAIN SENSOR POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Remove room lamp relay.
3.
Check continuity between room lamp relay harness connector and light & rain sensor harness connector.
Is the inspection result normal?
YES
>> Perform the interior room lamp power supply circuit diagnosis. Refer to
.
NO
>> Repair or replace harness.
3.
CHECK LIGHT & RAIN SENSOR GROUND CIRCUIT
Check continuity between light & rain sensor harness connector and ground.
Condition
Auto light function
Light & rain sensor
When illuminating
Not operating
When shutting off light
Operating
+
-
Voltage
Light & rain sensor
Connector
Terminal
R5
1
Ground Battery
voltage
Room lamp relay
Light & rain sensor
Continuity
Connector
Terminal
Connector
Terminal
M80
7
R5
1
Existed
Light & rain sensor
—
Continuity
Connector
Terminal
R5
3
Ground
Existed
EXL-142
< DTC/CIRCUIT DIAGNOSIS >
[LED HEADLAMP]
LIGHT & RAIN SENSOR
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK LIGHT & RAIN SENSOR SIGNAL
1.
Connect light & rain sensor connector.
2.
Turn ignition switch ON.
3.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace light & rain sensor. Refer to
EXL-171, "Removal and Installation"
NO
>> GO TO 5.
5.
CHECK LIGHT & RAIN SENSOR SIGNAL CIRCUIT (OPEN)
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector and light & rain sensor connector.
3.
Check continuity between BCM harness connector and light & rain sensor harness connector.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
6.
CHECK LIGHT & RAIN SENSOR SIGNAL CIRCUIT (SHORT)
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-132, "Removal and Installation"
.
NO
>> Repair or replace harness.
+
-
Condition
Voltage
(Approx.)
BCM
Connector
Terminal
M70
47
Ground
Ignition switch
ON
8.7V
JPMIA0156GB
BCM
Light & rain sensor
Continuity
Connector
Terminal
Connector
Terminal
M70
47
R5
2
Existed
BCM
—
Continuity
Connector
Terminal
M70
47
Ground
Not existed
HAZARD SWITCH
EXL-143
< DTC/CIRCUIT DIAGNOSIS >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
HAZARD SWITCH
Component Function Check
INFOID:0000000010338832
1.
CHECK HAZARD SWITCH SIGNAL
With CONSULT
1.
Turn ignition switch ON.
2.
Select “FLASHER” of “BCM” using CONSULT.
3.
Select “HAZARD SW” in “Data Monitor” mode.
4.
With operating the hazard switch, check the monitor status.
Is the inspection result normal?
YES
>> Hazard switch circuit is normal.
NO
>> Refer to
EXL-143, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000010338833
1.
CHECK HAZARD SWITCH SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect hazard switch connector.
3.
Check voltage between hazard switch connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 2.
2.
CHECK HAZARD SWITCH SIGNAL CIRCUIT (OPEN)
1.
Disconnect BCM connector.
2.
Check continuity between hazard switch harness connector and BCM harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK HAZARD SWITCH SIGNAL CIRCUIT (SHORT)
Check continuity between hazard switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-132, "Removal and Installation"
.
Monitor item
Condition
Monitor status
HAZARD SW
Hazard switch
ON
On
OFF
Off
+
-
Voltage
Hazard switch
Connector
Terminal
M39
2
Ground
9 – 16 V
Hazard switch
BCM
Continuity
Connector
Terminal
Connector
Terminal
M39
2
M70
51
Existed
Hazard switch
—
Continuity
Connector
Terminal
M39
2
Ground
Not existed
EXL-144
< DTC/CIRCUIT DIAGNOSIS >
[LED HEADLAMP]
HAZARD SWITCH
NO
>> Repair or replace harness.
4.
CHECK HAZARD SWITCH GROUND CIRCUIT
Check continuity between hazard switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
CHECK HAZARD SWITCH
Check hazard switch. Refer to
EXL-144, "Component Inspection"
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace hazard switch. Refer to
EXL-168, "Removal and Installation"
Component Inspection
INFOID:0000000010452497
1.
CHECK HAZARD SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect hazard switch connector.
3.
Check continuity of hazard switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace hazard switch. Refer to
EXL-168, "Removal and Installation"
Hazard switch
—
Continuity
Connector
Terminal
M39
1
Ground
Existed
Hazard switch
Condition
Continuity
Terminal
1
2
Hazard switch
ON
Existed
OFF
Not existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст