Nissan Pathfinder (2009 year). Manual — part 277
EC-230
< COMPONENT DIAGNOSIS >
[VQ40DE]
P0441 EVAP CONTROL SYSTEM
2.
Check the rubber tube for clogging.
OK or NG
OK
>> GO TO 11.
NG
>> Clean the rubber tube using an air blower.
11.
CHECK DRAIN FILTER
EC-230, "Component Inspection"
OK or NG
OK
>> GO TO 10.
NG
>> Replace drain filter.
12.
CHECK EVAP CANISTER VENT CONTROL VALVE
EC-248, "Component Inspection"
OK or NG
OK
>> GO TO 13.
NG
>> Replace EVAP canister vent control valve.
13.
CHECK EVAP PURGE LINE
Inspect EVAP purge line (pipe and rubber tube). Check for evidence of leaks.
Refer to
.
OK or NG
OK
>> GO TO 14.
NG
>> Replace it.
14.
CLEAN EVAP PURGE LINE
Clean EVAP purge line (pipe and rubber tube) using air blower.
>> GO TO 15.
15.
CHECK INTERMITTENT INCIDENT
GI-49, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000004297419
DRAIN FILTER
1.
Check visually for insect nests in the drain filter air inlet.
2.
Check visually for cracks or flaws in the appearance.
3.
Check visually for cracks or flaws in the hose.
4.
Blow air into port A and check that it flows freely out of port B.
5.
Block port B.
6.
Blow air into port A and check that there is no leakage.
7.
If NG, replace drain filter.
PBIB3641E
2009 Pathfinder
P0442 EVAP CONTROL SYSTEM
EC-231
< COMPONENT DIAGNOSIS >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P0442 EVAP CONTROL SYSTEM
On Board Diagnosis Logic
INFOID:0000000004297420
This diagnosis detects leaks in the EVAP purge line using engine intake manifold vacuum.
If pressure does not increase, the ECM will check for leaks in the line between the fuel tank and EVAP canister
purge volume control solenoid valve, under the following Vacuum test conditions.
The EVAP canister vent control valve is closed to shut the EVAP purge line off. The EVAP canister purge vol-
ume control solenoid valve will then be opened to depressurize the EVAP purge line using intake manifold
vacuum. After this occurs, the EVAP canister purge volume control solenoid valve will be closed.
CAUTION:
• Use only a genuine NISSAN fuel filler cap as a replacement. If an incorrect fuel filler cap is used, the
MIL may illuminate.
• If the fuel filler cap is not tightened properly, the MIL may illuminate.
• Use only a genuine NISSAN rubber tube as a replacement.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0442
0442
EVAP control system
small leak detected
(negative pressure)
EVAP control system has a leak, EVAP
control system does not operate prop-
erly.
• Incorrect fuel tank vacuum relief valve
• Incorrect fuel filler cap used
• Fuel filler cap remains open or fails to close.
• Foreign matter caught in fuel filler cap.
• Leak is in line between intake manifold and EVAP
canister purge volume control solenoid valve.
• Foreign matter caught in EVAP canister vent con-
trol valve.
• EVAP canister or fuel tank leaks
• EVAP purge line (pipe and rubber tube) leaks
• EVAP purge line rubber tube bent
• Loose or disconnected rubber tube
• EVAP canister vent control valve and the circuit
• EVAP canister purge volume control solenoid
valve and the circuit
• Fuel tank temperature sensor
• O-ring of EVAP canister vent control valve is
missing or damaged
• Drain filter
• EVAP canister is saturated with water
• EVAP control system pressure sensor
• Fuel level sensor and the circuit
• Refueling EVAP vapor cut valve
• ORVR system leaks
PBIB3640E
2009 Pathfinder
EC-232
< COMPONENT DIAGNOSIS >
[VQ40DE]
P0442 EVAP CONTROL SYSTEM
DTC Confirmation Procedure
INFOID:0000000004297421
NOTE:
If DTC Confirmation Procedure has been previously conducted, always perform the following before conduct-
ing the next step.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
• Perform “DTC WORK SUPPORT” when the fuel level is between 1/4 and 3/4 full, and vehicle is placed
on flat level surface.
• Always perform test at a temperature of 0 to 30
°
C (32 to 86
°
F).
WITH CONSULT-III
1.
Turn ignition switch ON.
2.
Turn ignition switch OFF and wait at least 10 seconds.
3.
Turn ignition switch ON and select “DATA MONITOR” mode with CONSULT-III.
4.
Make sure that the following conditions are met.
COOLAN TEMP/S: 0 - 70
°
C (32 - 158
°
F)
INT/A TEMP SE: 0 - 30
°
C (32 - 86
°
F)
5.
Select “EVP SML LEAK P0442/P1442” of “EVAPORATIVE SYSTEM” in “DTC WORK SUPPORT” mode
with CONSULT-III.
Follow the instructions displayed.
NOTE:
If the engine speed cannot be maintained within the range displayed on the CONSULT-III screen, go to
6.
Make sure that “OK” is displayed.
If “NG” is displayed, refer to
.
NOTE:
Make sure that EVAP hoses are connected to EVAP canister purge volume control solenoid valve
properly.
WITH GST
NOTE:
Be sure to read the explanation of Driving Pattern ON
1.
Start engine.
2.
Drive vehicle according to Driving Pattern,
3.
Stop vehicle.
4.
Turn ignition switch OFF, wait at least 10 seconds.
5.
Turn ignition switch ON.
6.
Turn ignition switch OFF, wait at least 10 seconds and then turn ON.
7.
Select Service $07 with GST.
-
If P0442 is displayed on the screen, go to
.
-
If P0441 is displayed on the screen, go to
.
Diagnosis Procedure
INFOID:0000000004297422
1.
CHECK FUEL FILLER CAP DESIGN
1.
Turn ignition switch OFF.
2.
Check for genuine NISSAN fuel filler cap design.
OK or NG
OK
>> GO TO 2.
NG
>> Replace with genuine NISSAN fuel filler cap.
SEF915U
2009 Pathfinder
P0442 EVAP CONTROL SYSTEM
EC-233
< COMPONENT DIAGNOSIS >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
2.
CHECK FUEL FILLER CAP INSTALLATION
Check that the cap is tightened properly by rotating the cap clockwise.
OK or NG
OK
>> GO TO 3.
NG
>> 1.
Open fuel filler cap, then clean cap and fuel filler neck threads using air blower.
2.
Retighten until ratcheting sound is heard.
3.
CHECK FUEL FILLER CAP FUNCTION
Check for air releasing sound while opening the fuel filler cap.
OK or NG
OK
>> GO TO 5.
NG
>> GO TO 4.
4.
CHECK FUEL TANK VACUUM RELIEF VALVE
EC-237, "Component Inspection"
OK or NG
OK
>> GO TO 5.
NG
>> Replace fuel filler cap with a genuine one.
5.
INSTALL THE PRESSURE PUMP
To locate the EVAP leak, install EVAP service port adapter and pres-
sure pump to EVAP service port securely. For the location of EVAP
service port, refer to
.
NOTE:
Improper installation of the EVAP service port adapter to the EVAP service port may cause leaking.
With CONSULT-III>>GO TO 6.
Without CONSULT-III>>GO TO 7.
6.
CHECK FOR EVAP LEAK
With CONSULT-III
1.
Turn ignition switch ON.
2.
Select “EVAP SYSTEM CLOSE” of “WORK SUPPORT” mode with CONSULT-III.
3.
Touch “START” and apply pressure into the EVAP line until the pressure indicator reaches the middle of
the bar graph.
CAUTION:
BBIA0550E
SEF916U
2009 Pathfinder
EC-234
< COMPONENT DIAGNOSIS >
[VQ40DE]
P0442 EVAP CONTROL SYSTEM
• Never use compressed air or a high pressure pump.
• Never exceed 4.12 kPa (0.042 kg/cm
2
, 0.6 psi) of pressure in the system.
4.
Using EVAP leak detector, locate the EVAP leak. For the leak
detector, refer to the instruction manual for more details.
Refer to
.
OK or NG
OK
>> GO TO 8.
NG
>> Repair or replace.
7.
CHECK FOR EVAP LEAK
Without CONSULT-III
1.
Turn ignition switch OFF.
2.
Apply 12 volts DC to EVAP canister vent control valve (3). The
valve will close. (Continue to apply 12 volts until the end of test.)
-
Fuel filler pipe (top of frame view) (1)
-
EVAP control system pressure sensor (2)
-
EVAP canister (4)
-
Drain filter (5)
-
: Vehicle front
3.
Pressurize the EVAP line using pressure pump with 1.3 to 2.7
kPa (10 to 20 mmHg, 0.39 to 0.79 inHg), then remove pump and
EVAP service port adapter.
CAUTION:
• Never use compressed air or a high pressure pump.
• Never exceed 4.12 kPa (0.042 kg/cm
2
, 0.6 psi) of pressure in the system.
4.
Using EVAP leak detector, locate the EVAP leak. For the leak
detector, refer to the instruction manual for more details. Refer
to
.
OK or NG
OK
>> GO TO 8.
NG
>> Repair or replace.
8.
CHECK DRAIN FILTER
Refer to .
OK or NG
OK
>> GO TO 9.
NG
>> Replace drain filter.
9.
CHECK EVAP CANISTER VENT CONTROL VALVE
Check the following.
• EVAP canister vent control valve is installed properly.
EC-487, "Removal and Installation"
.
• EVAP canister vent control valve.
EC-248, "Component Inspection"
.
OK or NG
OK
>> GO TO 10.
SEF200U
AWBIA0134ZZ
SEF200U
2009 Pathfinder
P0442 EVAP CONTROL SYSTEM
EC-235
< COMPONENT DIAGNOSIS >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
NG
>> Repair or replace EVAP canister vent control valve and O-ring.
10.
CHECK IF EVAP CANISTER IS SATURATED WITH WATER
1.
Remove EVAP canister with EVAP canister vent control valve and EVAP control system pressure sensor
attached.
2.
Does water drain from the EVAP canister?
Yes or No
Yes
>> GO TO 11.
No (With CONSULT-III)>>GO TO 13.
No (Without CONSULT-III)>>GO TO 14.
11.
CHECK EVAP CANISTER
Weigh the EVAP canister with the EVAP canister vent control valve and EVAP control system pressure sensor
attached.
The weight should be less than 2.0 kg (4.4 lb).
OK or NG
OK (With CONSULT-III)>>GO TO 13.
OK (Without CONSULT-III)>>GO TO 14.
NG
>> GO TO 12.
12.
DETECT MALFUNCTIONING PART
Check the following.
• EVAP canister for damage
• EVAP hose between EVAP canister and drain filter for clogging or poor connection
>> Repair hose or replace EVAP canister.
13.
CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE OPERATION
With CONSULT-III
1.
Disconnect vacuum hose from EVAP canister purge volume control solenoid valve at EVAP service port.
2.
Start engine.
3.
Perform “PURG VOL CONT/V” in “ACTIVE TEST” mode.
4.
Touch “Qu” on CONSULT-III screen to increase “PURG VOL CONT/V” opening to 100%.
5.
Check vacuum hose for vacuum when revving engine up to 2,000 rpm.
OK or NG
OK
>> GO TO 17.
NG
>> GO TO 15.
14.
CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE OPERATION
Without CONSULT-III
1.
Start engine and warm it up to normal operating temperature.
2.
Stop engine.
3.
Disconnect vacuum hose from EVAP canister purge volume control solenoid valve at EVAP service port.
4.
Start engine and let it idle for at least 80 seconds.
5.
Check vacuum hose for vacuum when revving engine up to 2,000 rpm.
OK or NG
OK
>> GO TO 16.
NG
>> GO TO 15.
15.
CHECK VACUUM HOSE
BBIA0558E
Vacuum should exist.
2009 Pathfinder
EC-236
< COMPONENT DIAGNOSIS >
[VQ40DE]
P0442 EVAP CONTROL SYSTEM
Check vacuum hoses for clogging or disconnection. Refer to
.
OK or NG
OK
>> GO TO 16.
NG
>> Repair or reconnect the hose.
16.
CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
EC-245, "Component Inspection"
OK or NG
OK
>> GO TO 17.
NG
>> Replace EVAP canister purge volume control solenoid valve.
17.
CHECK FUEL TANK TEMPERATURE SENSOR
EC-195, "Component Inspection"
OK or NG
OK
>> GO TO 18.
NG
>> Replace fuel level sensor unit.
18.
CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR
EC-261, "Component Inspection"
OK or NG
OK
>> GO TO 19.
NG
>> Replace EVAP control system pressure sensor.
19.
CHECK EVAP PURGE LINE
Check EVAP purge line (pipe, rubber tube, fuel tank and EVAP canister) for cracks or improper connection.
Refer to
.
OK or NG
OK
>> GO TO 20.
NG
>> Repair or reconnect the hose.
20.
CLEAN EVAP PURGE LINE
Clean EVAP purge line (pipe and rubber tube) using air blower.
>> GO TO 21.
21.
CHECK EVAP/ORVR LINE
Check EVAP/ORVR line between EVAP canister and fuel tank for clogging, kinks, looseness and improper
connection. For location, refer to
.
OK or NG
OK
>> GO TO 22.
NG
>> Repair or replace hoses and tubes.
22.
CHECK RECIRCULATION LINE
Check recirculation line between filler neck tube and fuel tank for clogging, kinks, cracks, looseness and
improper connection.
OK or NG
OK
>> GO TO 23.
NG
>> Repair or replace hose, tube or filler neck tube.
23.
CHECK REFUELING EVAP VAPOR CUT VALVE
EC-410, "Component Inspection"
OK or NG
OK
>> GO TO 24.
NG
>> Replace refueling EVAP vapor cut valve with fuel tank.
24.
CHECK FUEL LEVEL SENSOR
MWI-33, "Component Inspection"
.
2009 Pathfinder
P0442 EVAP CONTROL SYSTEM
EC-237
< COMPONENT DIAGNOSIS >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
OK or NG
OK
>> GO TO 25.
NG
>> Replace fuel level sensor unit.
25.
CHECK INTERMITTENT INCIDENT
GI-49, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000004297423
FUEL TANK VACUUM RELIEF VALVE (BUILT INTO FUEL FILLER CAP)
1.
Wipe clean valve housing.
2.
Check valve opening pressure and vacuum.
3.
If out of specification, replace fuel filler cap as an assembly.
CAUTION:
Use only a genuine fuel filler cap as a replacement. If an incor-
rect fuel filler cap is used, the MIL may illuminate.
DRAIN FILTER
1.
Check visually for insect nests in the drain filter air inlet.
2.
Check visually for cracks or flaws in the appearance.
3.
Check visually for cracks or flaws in the hose.
4.
Blow air into port A and check that it flows freely out of port B.
5.
Block port B.
6.
Blow air into port A and check that there is no leakage.
7.
If NG, replace drain filter.
SEF445Y
Pressure:
15.3 - 20.0 kPa (0.156 - 0.204 kg/cm
2
, 2.22 -
2.90 psi)
Vacuum:
−
6.0 to
−
3.3 kPa (
−
0.061 to
−
0.034 kg/cm
2
,
−
0.87 to
−
0.48 psi)
SEF943S
PBIB3641E
2009 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст