Nissan Pathfinder (2009 year). Manual — part 456
INTAKE DOOR MOTOR
HAC-43
< COMPONENT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
COMPONENT DESCRIPTION
Intake door motor
The intake door motor is attached to the intake unit. It rotates so that
air is drawn from inlets set by the A/C auto amp. Motor rotation is
conveyed to a lever which activates the intake door.
Intake Door Motor Component Function Check
INFOID:0000000003935895
INSPECTION FLOW
1.
CONFIRM SYMPTOM BY PERFORMING OPERATIONAL CHECK - REC (
)
1.
Press the mode switch to vent mode(
).
2.
Press REC (
) switch. The REC (
)indicator should illuminate.
3.
Press REC (
) switch again. The REC (
) indicator should go out.
4.
Listen for intake door position change (you should hear blower sound changes slightly).
Can a symptom be duplicated?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
PERFORM COMPLETE OPERATIONAL CHECK
Perform a complete operational check and check for any symptoms. Refer to
.
Can a symptom be duplicated?
YES
>> Refer to
HAC-124, "How to Perform Trouble Diagnosis For Quick And Accurate Repair"
NO
>> System OK.
3.
CHECK FOR SERVICE BULLETINS
Check for any service bulletins.
>> GO TO 4.
4.
CHECK INTAKE DOOR OPERATION
Check and verify intake door mechanism for smooth operation.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair intake door mechanism.
5.
PERFORM SELF-DIAGNOSIS
Perform self-diagnosis to check for any codes. Refer to
HAC-24, "A/C Auto Amp. Self-Diagnosis"
Are any self-diagnosis codes present?
YES
>> Refer to
HAC-25, "A/C System Self-Diagnosis Code Chart"
.
NO
>> GO TO 6.
6.
RECHECK FOR ANY SYMPTOMS
Perform a complete operational check for any symptoms. Refer to
.
Does another symptom exist?
YES
>> Refer to
HAC-124, "How to Perform Trouble Diagnosis For Quick And Accurate Repair"
NO
>> Replace A/C auto amp. Refer to
VTL-7, "Removal and Installation"
.
WJIA1107E
2009 Pathfinder
HAC-44
< COMPONENT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONER]
INTAKE DOOR MOTOR
Intake Door Motor Diagnosis Procedure
INFOID:0000000003935896
SYMPTOM:
• Intake door does not change.
• Intake door motor does not operate normally.
DIAGNOSTIC PROCEDURE FOR INTAKE DOOR MOTOR
1.
CHECK A/C AUTO AMP. FOR POWER AND GROUND
1.
Turn ignition switch ON.
2.
Check voltage between A/C auto amp. harness connector M49
terminal 21 and terminal 22 while placing the HVAC system into
self-diagnostic mode.
Is the inspection result normal?
OK
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK INTAKE DOOR MOTOR CIRCUITS FOR SHORT TO GROUND
1.
Turn ignition switch OFF.
2.
Disconnect the A/C auto amp. harness connector.
3.
Check continuity between A/C auto amp. harness connector
M49 terminal 21, 22 and ground.
Is the inspection result normal?
OK
>> Replace A/C auto amp. Refer to
NO
>> Repair or replace harness as necessary.
3.
CHECK A/C AUTO AMP. FOR GROUND AND POWER
1.
Press the BACK button to back out of self-diagnostic mode.
2.
Check voltage between A/C auto amp. harness connector M49
terminal 21 and terminal 22 while placing the HVAC system into
self-diagnostic mode.
Is the inspection result normal?
OK
>> GO TO 4.
NO
>> Replace A/C auto amp. Refer to
VTL-7, "Removal and Installation"
4.
CHECK INTAKE DOOR MOTOR AND CIRCUITS FOR OPEN
Connector
Terminals
Condition
Voltage
(Approx.)
(+) (-)
A/C auto amp.:
M49
21
22
Self-diagnostic
mode
Battery volt-
age
AWIIA0146ZZ
21 - Ground
: Continuity should not exist.
22 - Ground
: Continuity should not exist.
AWIIA0147ZZ
Connector
Terminals
Condition
Voltage
(Approx.)
(+) (-)
A/C auto amp.:
M49
22 21
Self-diagnostic
mode
Battery
voltage
AWIIA0148ZZ
2009 Pathfinder
INTAKE DOOR MOTOR
HAC-45
< COMPONENT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
1.
Turn ignition switch OFF.
2.
Disconnect the A/C auto amp. harness connector.
3.
Check continuity between A/C auto amp. harness connector
M49 terminal 21 and terminal 22.
Is the inspection result normal?
OK
>> Replace intake door motor. Refer to
.
NO
>> GO TO 5.
5.
CHECK INTAKE DOOR MOTOR CIRCUITS FOR OPEN
1.
Disconnect the intake door motor harness connector.
2.
Check continuity between A/C auto amp. harness connector
M49 (A) terminal 21, 22 and the intake door motor harness con-
nector M58 (B) terminal 1, 6.
Is the inspection result normal?
YES
>> Replace intake door motor. Refer to
.
NO
>> Repair or replace harness as necessary.
Continuity should exist.
AWIIA0149ZZ
21 - 6
: Continuity should exist.
22 - 1
: Continuity should exist.
AWIIA0234ZZ
2009 Pathfinder
HAC-46
< COMPONENT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONER]
BLOWER MOTOR CONTROL SYSTEM
BLOWER MOTOR CONTROL SYSTEM
System Description
INFOID:0000000003935897
SYSTEM DESCRIPTION
Component Parts
Blower speed control system components are:
• A/C auto amp.
• A/C and AV switch assembly
• Variable blower control
• Front blower motor relay
• Front blower motor
• In-vehicle sensor
• Ambient sensor
• Optical sensor
• Intake sensor
System Operation
Automatic Mode
In the automatic mode, the blower motor speed is calculated by the A/C auto amp. and variable blower control
based on input from the in-vehicle sensor, optical sensor, intake sensor and ambient sensor, and potentio tem-
perature control (PTC).
When the air flow is increased, the blower motor speed is adjusted gradually to prevent a sudden increase in
air flow.
In addition to manual air flow control and the usual automatic air flow control, starting air flow control, low
water temperature starting control and high passenger compartment temperature starting control are avail-
able.
Starting Blower Speed Control
Start up from cold soak condition (Automatic mode).
In a cold start up condition where the engine coolant temperature is below 50
°
C (122
°
F), the blower will not
operate at blower speed 1 for a short period of time (up to 210 seconds). The exact start delay time varies
depending on the ambient and engine coolant temperatures.
In the most extreme case (very low ambient temperature) the blower starting delay will be 210 seconds as
described above. After the coolant temperature reaches 50
°
C (122
°
F), or the 210 seconds has elapsed, the
blower speed will increase to the objective blower speed.
Start up from usual operating or hot soak condition (Automatic mode).
The blower will begin operation momentarily after the AUTO switch is pushed. The blower speed will gradually
rise to the objective speed over a time period of 3 seconds or less (actual time depends on the objective
blower speed).
AWIIA0173GB
2009 Pathfinder
BLOWER MOTOR CONTROL SYSTEM
HAC-47
< COMPONENT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
Blower Speed Compensation - Sunload
When the in-vehicle temperature and the set temperature are very close, the blower will be operating at low
speed. The speed will vary depending on the sunload. During conditions of low or no sunload, the blower
operates at low speed. During high sunload conditions, the A/C auto amp. causes the blower speed to
increase.
Blower Speed Control Specification
COMPONENT DESCRIPTION
Variable Blower Control
The variable blower control is located on the cooling unit. The vari-
able blower control receives a gate voltage from the A/C auto amp.
to steplessly maintain the blower motor voltage in the 0 to 5 volt
range (approx.).
Front Blower Motor Component Function Check
INFOID:0000000003935898
INSPECTION FLOW
1.
CONFIRM SYMPTOM BY PERFORMING OPERATIONAL CHECK - FRONT BLOWER MOTOR
1.
Press the blower (+) switch. Blower should operate.
2.
Rotate the front blower control dial clockwise, and continue checking blower speed and fan symbol until
all speeds are checked.
Can the symptom be duplicated?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK FOR ANY SYMPTOMS
Perform a complete operational check for any symptoms. Refer to
.
Does another symptom exist?
YES
>> Refer to
HAC-124, "How to Perform Trouble Diagnosis For Quick And Accurate Repair"
NO
>> System OK.
3.
CHECK FOR SERVICE BULLETINS
Check for any service bulletins.
>> GO TO 4.
4.
PERFORM A/C AUTO AMP. SELF-DIAGNOSIS
Perform self-diagnosis to check for any codes. Refer to
HAC-24, "A/C Auto Amp. Self-Diagnosis"
Are any self-diagnosis codes present?
WJIA0441E
WJIA1111E
2009 Pathfinder
HAC-48
< COMPONENT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONER]
BLOWER MOTOR CONTROL SYSTEM
YES
>> Refer to
HAC-25, "A/C System Self-Diagnosis Code Chart"
.
NO
>> GO TO 5.
5.
PERFORM A/C AND AV SWITCH ASSEMBLY SELF-DIAGNOSIS
Perform self-diagnosis to check the A/C and AV switch assembly. Refer to
.
Is the inspection results normal?
YES
>> GO TO 6.
NO
>> Replace A/C and AV switch assembly. Refer to
VTL-7, "Removal and Installation"
.
6.
CHECK BLOWER MOTOR OPERATION
Check and verify blower motor operates manually in all speeds.
Does blower motor operate in all speeds?
YES
>> GO TO 7.
NO
>> Refer to
HAC-150, "Front Blower Motor Diagnosis Procedure"
.
7.
CHECK ENGINE COOLANT TEMPERATURE SENSOR CIRCUIT
Check engine coolant temperature sensor circuit. Refer to
EC-128, "Component Description"
(VQ40DE) or
EC-607, "Component Inspection"
(VK56DE).
Is the inspection results normal?
YES
>> GO TO 8.
NO
>> Replace engine coolant temperature sensor.
8.
RECHECK FOR ANY SYMPTOMS
Perform a complete operational check for any symptoms. Refer to
.
Does another symptom exist?
YES
>> Refer to
HAC-124, "How to Perform Trouble Diagnosis For Quick And Accurate Repair"
NO
>> Replace A/C auto amp. Refer to
VTL-7, "Removal and Installation"
Front Blower Motor Diagnosis Procedure
INFOID:0000000003935899
SYMPTOM: Blower motor operation is malfunctioning.
DIAGNOSTIC PROCEDURE FOR BLOWER MOTOR
SYMPTOM: Blower motor operation is malfunctioning under starting
blower speed control.
1.
CHECK FUSES
AWIIA0242ZZ
2009 Pathfinder
BLOWER MOTOR CONTROL SYSTEM
HAC-49
< COMPONENT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
Check 15A fuses [No. 24 and 27 (Located in the fuse and fusible link box)].
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 8.
2.
CHECK FRONT BLOWER MOTOR POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect front blower motor connector.
3.
Turn ignition switch ON.
4.
Press the A/C switch.
5.
Press the front blower control "+" switch to maximum speed.
6.
Check voltage between front blower motor harness connector
M62 terminal 2 and ground.
Is the inspection result normal?
YES
>> GO TO 11.
NO
>> GO TO 3.
3.
CHECK FRONT BLOWER MOTOR RELAY (SWITCH SIDE) POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect front blower motor relay.
3.
Check voltage between front blower motor relay harness con-
nector E22 terminals 5, 7 and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair harness or connector.
4.
CHECK FRONT BLOWER MOTOR RELAY
Turn ignition switch OFF.
Check front blower motor relay. Refer to
HAC-154, "Front Blower Motor Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace front blower motor relay.
5.
CHECK FRONT BLOWER MOTOR RELAY (SWITCH SIDE) CIRCUIT FOR OPEN
Check continuity between front blower motor relay harness connec-
tor E22 terminals 3, 6 and front blower motor harness connector
M62 terminal 2.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair harness or connector.
6.
CHECK VARIABLE BLOWER CONTROL POWER SUPPLY CIRCUIT FOR OPEN
Fuses are good.
2 - Ground
: Battery voltage
WJIA1331E
5 - Ground
: Battery voltage
7 - Ground
: Battery voltage
WJIA1634E
3, 6 - 2
: Continuity should exist.
WJIA1333E
2009 Pathfinder
HAC-50
< COMPONENT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONER]
BLOWER MOTOR CONTROL SYSTEM
1.
Disconnect variable blower control harness connector.
2.
Check continuity between front blower motor relay harness con-
nector E22 (A) terminals 3, 6 and variable blower control har-
ness connector M122 (B) terminal 4.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair harness or connector.
7.
CHECK FRONT BLOWER MOTOR RELAY (COIL SIDE) POWER SUPPLY
1.
Turn ignition switch ON.
2.
Check voltage between front blower motor relay harness con-
nector E22 terminal 1 and ground.
Is the inspection result normal?
YES
>> Repair front blower motor ground circuit or connector.
NO
>> Repair harness or connector.
8.
REPLACE FUSES
Replace fuses.
Does the fuse blow?
YES
>> • If fuse blows without activating the front blower motor, repair short between fuse and front
blower motor relay.
• If fuse blows activating the front blower motor, GO TO 9.
NO
>> Inspection End.
9.
CHECK FRONT BLOWER MOTOR POWER SUPPLY CIRCUIT FOR SHORT
1.
Turn ignition switch OFF.
2.
Disconnect front blower motor connector, front blower motor
relay and variable blower control connector.
3.
Check continuity between variable blower control harness con-
nector M122 terminal 4 and ground.
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> Repair harness or connector.
10.
CHECK FRONT BLOWER MOTOR
Check front blower motor. Refer to
HAC-154, "Front Blower Motor Component Inspection"
.
Is the inspection result normal?
YES
>> Replace variable blower control (front). Refer to
VTL-14, "Removal and Installation"
NO
>> Replace front blower motor. Refer to
VTL-12, "Removal and Installation"
11.
CHECK FRONT BLOWER MOTOR
Check front blower motor. Refer to
HAC-52, "Front Blower Motor Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 12.
NO
>> Replace front blower motor. Refer to
VTL-12, "Removal and Installation"
12.
CHECK BLOWER MOTOR GROUND CIRCUIT
3, 6 - 4
: Continuity should exist.
AWIIA0243ZZ
1 - Ground
: Battery voltage
WJIA0504E
4 - Ground
: Continuity should not exist.
AWIIA0177ZZ
2009 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст