Nissan Pathfinder (2009 year). Manual — part 239
DLN-394
< DISASSEMBLY AND ASSEMBLY >
[FRONT FINAL DRIVE: M205]
FRONT FINAL DRIVE
16. Install the extension tube with a new O-ring.
CAUTION:
• Do not reuse O-ring.
• If the extension tube is being replaced, install a new axle
shaft bearing.
17. Apply 3 mm (0.12 in) bead of sealant to the mating surface of
the carrier cover as shown.
• Use Genuine Silicone RTV or equivalent. Refer to
"Recommended Chemical Products and Sealants"
.
CAUTION:
Remove any old sealant adhering to the mating surfaces.
Also remove any moisture, oil, or foreign material adhering
to the application and mating surfaces.
18. Install the carrier cover to the gear carrier. Tighten the bolts to
the specified torque. Refer to
19. Install side shaft and side flange.
SDIA3205E
SDIA3204E
2009 Pathfinder
SERVICE DATA AND SPECIFICATIONS (SDS)
DLN-395
< SERVICE DATA AND SPECIFICATIONS (SDS)
[FRONT FINAL DRIVE: M205]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specification
INFOID:0000000003937449
Inspection and Adjustment
INFOID:0000000003937450
DRIVE GEAR RUNOUT
Unit: mm (in)
SIDE GEAR CLEARANCE
Unit: mm (in)
PRELOAD TORQUE
Unit: N·m (kg-m, in-lb)
BACKLASH
Unit: mm (in)
COMPANION FLANGE RUNOUT
Unit: mm (in)
SELECTIVE PARTS
Drive Pinion Height Adjusting Washer
Applied model
VK56DE
Final drive model
M205
Gear ratio
2.937
Number of teeth (Drive gear/Drive pinion)
47/16
Differential gear oil capacity (Approx.)
1.6
(3 3/8 US pt, 2 7/8 Imp pt)
Number of pinion gears
2
Drive pinion adjustment spacer type
Collapsible
Item
Runout limit
Drive gear back face
0.08 (0.0031) or less
Item
Specification
Side gear back clearance (Clearance between side gear and dif-
ferential case for adjusting side gear backlash)
0.20 (0.0079) or less
(Each gear should rotate smoothly without excessive resistance
during differential motion.)
Item
Specification
Drive pinion bearing preload torque
2.3 - 3.4 (0.23 - 0.35, 21 - 31)
Total preload torque
(Total preload torque = drive pinion bearing preload torque + side
bearing preload torque).
2.98 - 4.76 (0.31 - 0.48, 27 - 42)
Item
Specification
Drive gear to drive pinion backlash
0.13 - 0.18 (0.0051 - 0.0071)
Item
Runout limit
Companion flange face
0.10 (0.0039) or less
Companion flange inner side
0.13 (0.0051) or less
2009 Pathfinder
DLN-396
< SERVICE DATA AND SPECIFICATIONS (SDS)
[FRONT FINAL DRIVE: M205]
SERVICE DATA AND SPECIFICATIONS (SDS)
Unit: mm (in)
*Always check with the Parts Department for the latest parts information.
Side Gear Thrust Washer
Unit: mm (in)
*: Always check with the Parts Department for the latest parts information.
Thickness
Package part number*
1.22 (0.048)
1.24 (0.049)
1.27 (0.050)
1.30 (0.051)
1.32 (0.052)
38154 8S111
1.35 (0.053)
1.37 (0.054)
1.40 (0.055)
1.42 (0.056)
1.45 (0.057)
38154 8S112
1.47 (0.058)
1.50 (0.059)
1.52 (0.060)
1.55 (0.061)
1.57 (0.062)
38154 8S113
1.60 (0.063)
1.63 (0.064)
1.65 (0.065)
1.68 (0.066)
1.70 (0.067)
38154 8S114
1.73 (0.068)
1.75 (0.069)
1.78 (0.070)
1.80 (0.071)
1.83 (0.072)
38154 8S115
Thickness
Package part number*
0.76 (0.030)
0.79 (0.031)
0.81 (0.032)
0.84 (0.033)
0.87 (0.034)
38424 8S111
0.89 (0.035)
0.91 (0.036)
0.94 (0.037)
0.97 (0.038)
0.99 (0.039)
38424 8S112
2009 Pathfinder
PRECAUTIONS
DLN-397
< PRECAUTION >
[REAR FINAL DRIVE: R200]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Servicing Rear Final Drive
INFOID:0000000003937451
• Before starting diagnosis of the vehicle, understand the symptoms well. Perform correct and systematic
operations.
• Check for the correct installation status prior to removal or disassembly. When matching marks are required,
be certain they do not interfere with the function of the parts they are applied to.
• Overhaul should be done in a clean work area, a dust proof area is recommended.
• Before disassembly, completely remove sand and mud from the exterior of the unit, preventing them from
entering into the unit during disassembly or assembly.
• Always use shop paper for cleaning the inside of components.
• Avoid using cotton gloves or a shop cloth to prevent the entering of lint.
• Check appearance of the disassembled parts for damage, deformation, and abnormal wear. Replace them
with new ones if necessary.
• Gaskets, seals and O-rings should be replaced any time the unit is disassembled.
• Clean and flush the parts sufficiently and blow them dry.
• Be careful not to damage sliding surfaces and mating surfaces.
• When applying sealant, remove the old sealant from the mating surface; then remove any moisture, oil, and
foreign materials from the application and mating surfaces.
• In principle, tighten nuts or bolts gradually in several steps working diagonally from inside to outside. If a
tightening sequence is specified, observe it.
• During assembly, observe the specified tightening torque.
• Add new differential gear oil, petroleum jelly, or multi-purpose grease, as specified.
2009 Pathfinder
DLN-398
< PREPARATION >
[REAR FINAL DRIVE: R200]
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000003937452
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
KV40104000
(
—
)
Flange wrench
Removing and installing drive pinion lock nut
a: 85 mm (3.35 in) dia.
b: 65 mm (2.56 in) dia.
KV381054S0
(J-34286)
Puller
Removing front oil seal
ST30720000
(J-25405)
Drift
• Installing front oil seal
• Installing drive pinion rear bearing outer
race
a: 77 mm (3.03 in) dia.
b: 55.5 mm (2.185 in) dia.
ST36230000
(J-25840-A)
Sliding hammer
Removing side flange
KV40104100
(
—
)
Attachment
Removing side flange
KV38100200
(J-26233)
Drift
Installing side oil seal
a: 65 mm (2.56 in) dia.
b: 49 mm (1.93 in) dia.
NT659
ZZA0601D
ZZA0811D
ZZA0803D
ZZA0804D
ZZA1143D
2009 Pathfinder
PREPARATION
DLN-399
< PREPARATION >
[REAR FINAL DRIVE: R200]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
KV38107900
(J-39352)
Protector
Installing side flange
KV38100800
(J-25604-01)
Attachment
Securing unit assembly
a: 541 mm (21.30 in)
b: 200 mm (7.87 in)
ST3127S000
(J-25765-A)
Preload gauge
1: GG91030000
(J-25765)
Torque wrench
2: HT62940000
(
—
)
Socket adapter (1/2
″
)
3: HT62900000
(
—
)
Socket adapter (3/8
″
)
Measuring drive pinion bearing preload torque
and total preload torque
KV10111100
(J-37228)
Seal cutter
Removing carrier cover
ST3306S001
(
—
)
Differential side bearing puller set
1: ST33051001
(J-22888-20)
Puller
2: ST33061000
(J-8107-2)
Base
Removing and installing side bearing inner
race
a: 28.5 mm (1.122 in) dia.
b: 38 mm (1.50 in) dia.
ST30031000
(J-22912-01)
Puller
Removing drive pinion rear bearing inner race
Tool number
(Kent-Moore No.)
Tool name
Description
S-NT129
SDIA0267E
NT124
S-NT046
NT072
ZZA0700D
2009 Pathfinder
DLN-400
< PREPARATION >
[REAR FINAL DRIVE: R200]
PREPARATION
KV40105230
(
—
)
Drift
Installing drive pinion rear bearing outer race
a: 92 mm (3.62 in) dia.
b: 86 mm (3.39 in) dia.
c: 45 mm (1.77 in) dia.
ST30611000
(J-25742-1)
Drift bar
Installing drive pinion front bearing outer race
(Use with ST30613000)
ST30613000
(J-25742-3)
Drift
Installing drive pinion front bearing outer race
a: 72 mm (2.83 in) dia.
b: 48 mm (1.89 in) dia.
KV38100300
(J-25523)
Drift
Installing side bearing inner race
a: 54 mm (2.13 in) dia.
b: 46 mm (1.81 in) dia.
c: 32 mm (1.26 in) dia.
ST30901000
(J-26010-01)
Drift
Installing drive pinion rear bearing inner race
a: 79 mm (3.11 in) dia.
b: 45 mm (1.77 in) dia.
c: 35.2 mm (1.386 in) dia.
HT72400000
(
—
)
Slide hammer
Removing differential case assembly
—
(J-8129)
Spring gauge
Measuring turning torque
Tool number
(Kent-Moore No.)
Tool name
Description
PDIA0591E
S-NT090
ZZA1000D
ZZA1046D
ZZA0978D
S-NT125
NT127
2009 Pathfinder
PREPARATION
DLN-401
< PREPARATION >
[REAR FINAL DRIVE: R200]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
Commercial Service Tool
INFOID:0000000003937453
—
(J-34309)
Differential shim selector tool
Adjusting drive pinion bearing preload and
drive pinion height
—
(J-25269-4)
Side bearing disc (2 Req'd)
Selecting drive pinion height adjusting washer
KV10112100
(BT-8653-A)
Angle wrench
Tightening bolts for drive gear
Tool number
(Kent-Moore No.)
Tool name
Description
NT134
NT136
NT014
Tool name
Description
Spacer
Installing drive pinion front bearing inner race
a: 60 mm (2.36 in) dia.
b: 36 mm (1.42 in) dia.
c: 30 mm (1.18 in)
Power tool
Loosening nuts and bolts
ZZA1133D
PBIC0190E
2009 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст