Nissan Pathfinder (2009 year). Manual — part 221
DLN-250
< SYMPTOM DIAGNOSIS >
[TRANSFER: TX15B]
4WD WARNING LAMP DOES NOT TURN ON
4.
CHECK INDICATOR LAMP CIRCUIT
1.
Turn ignition switch “OFF”. (Stay for at least 5 seconds.)
2.
Connect combination meter harness connector.
3.
Disconnect transfer control unit harness connector.
4.
Turn ignition switch "ON". (Do not start engine.)
5.
Ground the following terminal using suitable wiring.
-
Transfer control unit harness connector M166 terminal 38 and
ground.
Does the indicator lamp turn on?
YES
>> GO TO 5.
NO
>> Replace the combination meter. Refer to
.
5.
SYMPTOM CHECK
Check again.
Does the symptom still occur?
YES
>> GO TO 6.
NO
>> Inspection End.
6.
CHECK TRANSFER CONTROL UNIT
Check transfer control unit input/output signal. Refer to
Are the inspection results normal?
YES
>> Inspection End.
NO
>> Check transfer control unit pin terminals for damage or loose connection with harness connector.
If any items are damaged, repair or replace damaged parts.
SDIA3452E
2009 Pathfinder
4WD SHIFT INDICATOR LAMP AND 4LO INDICATOR LAMP DO NOT TURN ON
DLN-251
< SYMPTOM DIAGNOSIS >
[TRANSFER: TX15B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
4WD SHIFT INDICATOR LAMP AND 4LO INDICATOR LAMP DO NOT
TURN ON
Description
INFOID:0000000003937370
4WD shift indicator lamp and 4LO indicator lamp do not turn ON for approx. 1 second when turning ignition
switch to ON.
Diagnosis Procedure
INFOID:0000000003937371
1.
CHECK TRANSFER CONTROL UNIT POWER SUPPLY AND GROUND CIRCUITS
DLN-202, "Diagnosis Procedure"
Are the inspection results normal?
YES
>> GO TO 2.
NO
>> Perform repairs as necessary.
2.
CHECK COMBINATION METER POWER SUPPLY CIRCUIT
1.
Turn ignition switch “OFF”. (Stay for at least 5 seconds.)
2.
Disconnect combination meter harness connector.
3.
Check voltage between combination meter harness connector
terminals and ground.
4.
Turn ignition switch “ON”. (Do not start engine.)
5.
Check voltage between combination meter harness connector
terminals and ground.
Are the inspection results normal?
YES
>> GO TO 3.
NO
>>
Check the following. If any items are damaged, repair
or replace damaged parts.
• 10A fuse [No. 14, located in the fuse block (J/B) or]
ignition switch.
• Harness for short or open between ignition switch and combination meter harness connector
terminal 16
3.
CHECK HARNESS BETWEEN TRANSFER CONTROL UNIT AND COMBINATION METER
1.
Turn ignition switch “OFF”. (Stay for at least 5 seconds.)
Connector
Terminal
Voltage (Approx.)
M24
16 - Ground
0V
WDIA0178E
Connector
Terminal
Voltage (Approx.)
M24
16 - Ground
Battery voltage
WDIA0179E
2009 Pathfinder
DLN-252
< SYMPTOM DIAGNOSIS >
[TRANSFER: TX15B]
4WD SHIFT INDICATOR LAMP AND 4LO INDICATOR LAMP DO NOT TURN ON
2.
Check continuity between the following terminals.
-
Transfer control unit harness connector M166 terminal 35 and
combination meter harness connector M24 terminal 30.
-
Transfer control unit harness connector M166 terminal 36 and
combination meter harness connector M24 terminal 27.
-
Transfer control unit harness connector M166 terminal 37 and
combination meter harness connector M24 terminal 29.
Also check harness for short to ground and short to power.
Does continuity exist?
YES
>> GO TO 4.
NO
>> Repair or replace damaged parts.
4.
CHECK INDICATOR LAMP CIRCUIT
1.
Turn ignition switch “OFF”. (Stay for at least 5 seconds.)
2.
Connect combination meter harness connector.
3.
Disconnect transfer control unit harness connector.
4.
Turn ignition switch "ON". (Do not start engine.)
5.
Ground the following terminals using suitable wiring.
-
Transfer control unit harness connector M166 terminal 35 and
ground.
-
Transfer control unit harness connector M166 terminal 36 and
ground.
-
Transfer control unit harness connector M166 terminal 37 and
ground.
Do indicator lamps turn on?
YES
>> GO TO 5.
NO
>> Replace the combination meter. Refer to
.
5.
SYMPTOM CHECK
Check again.
Does the symptom still occur?
YES
>> GO TO 6.
NO
>> Inspection End.
6.
CHECK TRANSFER CONTROL UNIT
Check transfer control unit input/output signal. Refer to
Are the inspection results normal?
YES
>> Inspection End.
NO
>> Check transfer control unit pin terminals for damage or loose connection with harness connector.
If any items are damaged, repair or replace damaged parts.
Continuity should exist.
SDIA2823E
SDIA3451E
2009 Pathfinder
4WD SHIFT INDICATOR LAMP OR 4LO INDICATOR LAMP DO NOT CHANGE
DLN-253
< SYMPTOM DIAGNOSIS >
[TRANSFER: TX15B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
4WD SHIFT INDICATOR LAMP OR 4LO INDICATOR LAMP DO NOT
CHANGE
Description
INFOID:0000000003937372
4WD shift indicator lamp or 4LO indicator lamp do not change when switching the 4WD shift switch.
Diagnosis Procedure
INFOID:0000000003937373
1.
CONFIRM THE SYMPTOM
Confirm 4WD shift indicator lamp and 4LO indicator lamp when ignition switch is turned to ON.
Do 4WD shift indicator lamp and 4LO indicator lamp turn on?
YES
>> GO TO 2.
NO
>> Go to
DLN-251, "Diagnosis Procedure"
.
2.
CHECK SYSTEM FOR 4WD SHIFT SWITCH
Perform trouble diagnosis for 4WD shift switch system. Refer to
DLN-212, "Diagnosis Procedure"
.
Are the inspection results normal?
YES
>> GO TO 3.
NO
>> Repair or replace damaged parts.
3.
CHECK SYSTEM FOR WAIT DETECTION SWITCH
Perform trouble diagnosis for wait detection switch system. Refer to
DLN-215, "Diagnosis Procedure"
Are the inspection results normal?
YES
>> GO TO 4.
NO
>> Repair or replace damaged parts.
4.
CHECK SYSTEM FOR 4LO SWITCH
Perform trouble diagnosis for 4LO switch system. Refer to
DLN-209, "Diagnosis Procedure"
.
Are the inspection results normal?
YES
>> GO TO 5.
NO
>> Repair or replace damaged parts.
5.
CHECK SYSTEM FOR ATP SWITCH
Perform trouble diagnosis for ATP switch system. Refer to
DLN-259, "Diagnosis Procedure"
Are the inspection results normal?
YES
>> GO TO 6.
NO
>> Repair or replace damaged parts.
6.
SYMPTOM CHECK
Check again.
Does the symptom still occur?
YES
>> GO TO 7.
NO
>> Inspection End
7.
CHECK TRANSFER CONTROL UNIT
Check transfer control unit input/output signal. Refer to
Are the inspection results normal?
YES
>> GO TO 8.
NO
>> Check transfer control unit pin terminals for damage or loose connection with harness connector.
If any items are damaged, repair or replace damaged parts.
8.
CHECK TRANSFER INNER PARTS
1.
Disassemble transfer assembly. Refer to
DLN-281, "Disassembly and Assembly"
2.
Check transfer inner parts.
Are the inspection results normal?
2009 Pathfinder
DLN-254
< SYMPTOM DIAGNOSIS >
[TRANSFER: TX15B]
4WD SHIFT INDICATOR LAMP OR 4LO INDICATOR LAMP DO NOT CHANGE
YES
>> Inspection End.
NO
>> Repair or replace damaged parts.
2009 Pathfinder
ATP WARNING LAMP DOES NOT TURN ON
DLN-255
< SYMPTOM DIAGNOSIS >
[TRANSFER: TX15B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
ATP WARNING LAMP DOES NOT TURN ON
Description
INFOID:0000000003937374
ATP warning lamp does not turn ON when the transfer case is switched in or out of 4LO with the A/T selector
lever in N position.
Diagnosis Procedure
INFOID:0000000003937375
1.
CHECK SYSTEM FOR CAN COMMUNICATION LINE
Perform self-diagnosis. Refer to
DLN-198, "CONSULT-III Function (ALL MODE AWD/4WD)"
Do the self-diagnostic results indicate CAN communication?
YES
>> Perform trouble diagnosis for CAN communication line. Refer to
.
NO
>> GO TO 2.
2.
CHECK SYSTEM FOR 4WD SHIFT SWITCH
Perform trouble diagnosis for 4WD shift switch system. Refer to
DLN-212, "Diagnosis Procedure"
.
Are the inspection results normal?
YES
>> GO TO 3.
NO
>> Repair or replace damaged parts.
3.
CHECK SYSTEM FOR PNP SWITCH SIGNAL
Perform trouble diagnosis for PNP switch signal system. Refer to
DLN-218, "Diagnosis Procedure"
.
Are the inspection results normal?
YES
>> GO TO 4.
NO
>> Repair or replace damaged parts.
4.
CHECK SYSTEM FOR ATP SWITCH
Perform trouble diagnosis for ATP switch system. Refer to
DLN-259, "Diagnosis Procedure"
Are the inspection results normal?
YES
>> GO TO 5.
NO
>> Repair or replace damaged parts.
5.
CHECK ATP WARNING LAMP CIRCUIT
1.
Disconnect ATP switch harness connector.
2.
Turn ignition switch “ON”. (Do not start engine.)
3.
Ground terminal 8 on ATP switch connector F71 using suitable
wiring.
4.
Turn ignition switch “OFF”. (Stay for at least 5 seconds.)
Does ATP warning lamp turn on?
YES
>> GO TO 9.
NO
>> GO TO 6.
6.
CHECK HARNESS BETWEEN TRANSFER CONTROL UNIT AND COMBINATION METER
1.
Turn ignition switch “OFF”. (Stay for at least 5 seconds.)
2.
Disconnect transfer control unit harness connector and combination meter harness connector.
SDIA2832E
2009 Pathfinder
DLN-256
< SYMPTOM DIAGNOSIS >
[TRANSFER: TX15B]
ATP WARNING LAMP DOES NOT TURN ON
3.
Check continuity between transfer control unit harness connec-
tor M166 terminal 39 and combination meter harness connector
M24 terminal 21.
Also check harness for short to ground and short to power.
Does continuity exist?
YES
>> GO TO 7.
NO
>> Repair or replace damaged parts.
7.
CHECK HARNESS BETWEEN COMBINATION METER AND ATP SWITCH
1.
Turn ignition switch “OFF”. (Stay for at least 5 seconds.)
2.
Disconnect ATP switch harness connector.
3.
Check continuity between combination meter harness connector
M24 terminal 1 and ATP switch harness connector F71 terminal
8.
Also check harness for short to ground and short to power.
Does continuity exist?
YES
>> GO TO 8.
NO
>> Repair or replace damaged parts.
8.
SYMPTOM CHECK
Check again.
Does the symptom still occur?
YES
>> GO TO 9.
NO
>> Inspection End.
9.
CHECK TRANSFER CONTROL UNIT
Check transfer control unit input/output signal. Refer to
Are the inspection results normal?
YES
>> GO TO 10.
NO
>> Check transfer control unit pin terminals for damage or loose connection with harness connector.
If any items are damaged, repair or replace damaged parts.
10.
CHECK TRANSFER INNER PARTS
1.
Disassemble transfer assembly. Refer to
DLN-281, "Disassembly and Assembly"
2.
Check transfer inner parts.
Are the inspection results normal?
YES
>> Inspection End.
NO
>> Repair or replace damaged parts.
Continuity should exist.
SDIA2825E
Continuity should exist.
SDIA2833E
2009 Pathfinder
4WD SHIFT INDICATOR LAMP KEEPS FLASHING
DLN-257
< SYMPTOM DIAGNOSIS >
[TRANSFER: TX15B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
4WD SHIFT INDICATOR LAMP KEEPS FLASHING
Description
INFOID:0000000003937376
The 4WD shift indicator lamp keeps flashing.
Diagnosis Procedure
INFOID:0000000003937377
1.
CONFIRM THE SYMPTOM
1.
Set 4WD shift switch to “2WD”.
2.
Drive the vehicle straight forward and backward keeping speed under 20 km/h (12 MPH).
Does 4WD shift indicator lamp keep flashing?
YES
>> GO TO 2.
NO
>> Inspection End.
2.
CHECK SYSTEM FOR WAIT DETECTION SWITCH
Perform trouble diagnosis for wait detection switch system. Refer to
DLN-215, "Diagnosis Procedure"
Are the inspection results normal?
YES
>> GO TO 3.
NO
>> Repair or replace damaged parts.
3.
CHECK SYSTEM FOR 4LO SWITCH
Perform trouble diagnosis for 4LO switch. Refer to
DLN-209, "Diagnosis Procedure"
.
Are the inspection results normal?
YES
>> GO TO 4.
NO
>> Repair or replace damaged parts.
4.
SYMPTOM CHECK
Check again.
Does the symptom still occur?
YES
>> GO TO 5.
NO
>> Inspection End.
5.
CHECK TRANSFER CONTROL UNIT
Check transfer control unit input/output signal. Refer to
Are the inspection results normal?
YES
>> GO TO 6.
NO
>> Check transfer control unit pin terminals for damage or loose connection with harness connector.
If any items are damaged, repair or replace damaged parts.
6.
CHECK TRANSFER INNER PARTS
1.
Disassemble transfer assembly. Refer to
DLN-281, "Disassembly and Assembly"
2.
Check transfer inner parts.
Are the inspection results normal?
YES
>> Inspection End.
NO
>> Repair or replace damaged parts.
2009 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст