Nissan Pathfinder (2009 year). Manual — part 9
DOOR MIRROR REMOTE CONTROL SWITCH
ADP-59
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
Check door mirror remote control switch.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace door mirror remote control switch. Refer to
ADP-161, "Removal and Installation"
MIRROR SWITCH
MIRROR SWITCH : Description
INFOID:0000000003935537
It operates angle of the door mirror face.
It transmits mirror face adjust operation to automatic drive positioner control unit.
MIRROR SWITCH : Component Function Check
INFOID:0000000003935538
1.
CHECK MIRROR SWITCH FUNCTION
Check the operation on “MIR CON SW–UP/DN” and “MIR CON SW–RH/LH” in “DATA MONITOR” mode
with CONSULT-III.
Refer to
ADP-25, "CONSULT-III Function"
.
Is the inspection result normal?
YES
>> Mirror switch function is OK.
NO
>> Refer to
ADP-59, "MIRROR SWITCH : Diagnosis Procedure"
.
MIRROR SWITCH : Diagnosis Procedure
INFOID:0000000003935539
1.
CHECK MIRROR SWITCH FUNCTION
1.
Turn ignition switch ON.
2.
Check voltage between automatic drive positioner control unit
connector and ground.
Is the inspection result normal?
YES
>> GO TO 6
NO
>> GO TO 2
2.
CHECK HARNESS CONTINUITY
Terminal
Change over switch
condition
Continuity
Door mirror remote control switch
2
13
LEFT
Yes
Other than above
No
3
RIGHT
Yes
Other than above
No
LIIA2052E
Terminals
Mirror switch
Condition
Voltage (V)
(Approx.)
(+)
(–)
Automatic drive
positioner control
unit connector
Terminal
M33
3
Ground
UP
0
Other than above
5
4
LEFT
0
Other than above
5
19
DOWN
0
Other than above
5
20
RIGHT
0
Other than above
5
PIIA4771E
2009 Pathfinder
ADP-60
< COMPONENT DIAGNOSIS >
DOOR MIRROR REMOTE CONTROL SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit and door mir-
ror remote control switch.
3.
Check continuity between automatic drive positioner control unit
connector and door mirror remote control switch connector.
4.
Check continuity between automatic drive positioner control unit connector and ground.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Repair or replace harness.
3.
CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT
Check continuity between door mirror remote control switch connec-
tor and ground.
Is the inspection result normal?
YES
>> GO TO 4
NO
>> Repair or replace harness.
4.
CHECK AUTOMATIC DRIVE POSITIONER CONTROL UNIT OUTPUT SIGNAL
1.
Connect automatic drive positioner control unit.
2.
Turn ignition switch ON.
3.
Check voltage between automatic drive positioner control unit
and ground.
Is the inspection result normal?
Automatic drive
positioner control
unit connector
Terminal
Door mirror remote
control switch con-
nector
Terminal
Continuity
M33
3
M163
6
Yes
4
5
19
14
20
4
Automatic drive positioner
control unit connector
Terminal
Ground
Continuity
M33
3
No
4
19
20
LIIA1823E
Door mirror remote control
switch connector
Terminal
Ground
Continuity
M163
13
Yes
LIIA1825E
Terminals
Voltage (V)
(Approx.)
(+)
(-)
Automatic drive positioner
control unit connector
Terminal
M33
3
Ground
5
4
19
20
PIIA4771E
2009 Pathfinder
DOOR MIRROR REMOTE CONTROL SWITCH
ADP-61
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
YES
>> GO TO 5
NO
>> Replace automatic drive positioner control unit. Refer to
ADP-159, "Removal and Installation"
.
5.
CHECK MIRROR SWITCH
Check mirror switch.
Refer to
ADP-61, "MIRROR SWITCH : Component Inspection"
.
Is the inspection result normal?
YES
>> Refer to
GI-49, "Intermittent Incident"
.
NO
>> Replace door mirror remote control switch. Refer to
ADP-161, "Removal and Installation"
6.
CHECK INTERMITTENT INCIDENT
Check intermittent incident.
Refer to
GI-49, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> Replace automatic drive positioner control unit. Refer to
ADP-159, "Removal and Installation"
.
NO
>> Repair or replace the malfunctioning parts.
MIRROR SWITCH : Component Inspection
INFOID:0000000003935540
1.
CHECK MIRROR SWITCH
Check door mirror remote control switch.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace door mirror remote control switch. Refer to
ADP-161, "Removal and Installation"
Terminal
Mirror switch condition
Continuity
Door mirror remote
control switch
4
13
RIGHT
Yes
Other than above
No
5
LEFT
Yes
Other than above
No
6
UP
Yes
Other than above
No
14
DOWN
Yes
Other than above
No
LIIA2053E
2009 Pathfinder
ADP-62
< COMPONENT DIAGNOSIS >
POWER SEAT SWITCH GROUND CIRCUIT
POWER SEAT SWITCH GROUND CIRCUIT
Diagnosis Procedure
INFOID:0000000003935541
1.
CHECK POWER SEAT SWITCH LH GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect power seat switch LH.
3.
Check continuity between power seat switch LH connector and
ground.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
NO
>> Repair or replace harness.
Power seat switch LH
connector
Terminal
Ground
Continuity
B208
7
Yes
ALJIA0316ZZ
2009 Pathfinder
DETENTION SWITCH
ADP-63
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
DETENTION SWITCH
Description
INFOID:0000000003935542
Park position switch is installed on A/T device. It is turned OFF when the A/T selector lever is in P position.
The driver seat control unit judges that the A/T selector lever is in P position if continuity does not exist in this
circuit.
Component Function Check
INFOID:0000000003935543
1.
CHECK FUNCTION
1.
Select “DETENT SW” signal in “Data monitor” mode with CONSULT-III.
2.
Check park position switch signal under the following conditions.
Is the indication normal?
YES
>> Inspection End.
NO
>> Perform diagnosis procedure. Refer to
Diagnosis Procedure
INFOID:0000000003935544
1.
CHECK DTC WITH “BCM”
Check “Self Diagnostic Result” for BCM with CONSULT-lll.
Is any other DTC detected?
YES
>> Check the DTC.
NO
>> GO TO 2
2.
CHECK PARK POSITION SWITCH INPUT SIGNAL
1.
Turn ignition switch ON.
2.
Mechanical key must be removed from the key switch.
3.
Check voltage between driver seat control unit harness connec-
tor and ground.
Is the inspection result normal?
YES
>> GO TO 4
NO
>> GO TO 3
3.
CHECK PARK POSITION SWITCH CIRCUIT
Monitor item
Condition
Status
DETENT SW
A/T selector lever
P position
OFF
Other than
above
ON
Driver seat
control unit
connector
Terminal
Condition
Voltage (V)
(Approx.)
(+)
(-)
B202
21
Ground
A/T selec-
tor lever
P position
Battery volt-
age
Other than
above
0V
LIIA2238E
2009 Pathfinder
ADP-64
< COMPONENT DIAGNOSIS >
DETENTION SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect driver seat control unit and A/T device.
3.
Check continuity between driver seat control unit harness con-
nector and A/T device harness connector.
4.
Check continuity between A/T device harness connector and
ground.
Is the inspection result normal?
YES
>> GO TO 4
NO
>> Repair or replace harness.
4.
CHECK INTERMITTENT INCIDENT
GI-49, "Intermittent Incident"
Is the inspection result normal?
YES
>> Replace driver seat control unit. Refer to
NO
>> Repair or replace the malfunctioning part.
Driver seat control unit
A/T device
Continuity
Connector
Terminal
Connector
Terminal
B202
21
M158
4
Yes
A/T device
Ground
Continuity
Connector
Terminal
M158
4
No
LIIA1774E
2009 Pathfinder
FRONT DOOR SWITCH (DRIVER SIDE)
ADP-65
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
FRONT DOOR SWITCH (DRIVER SIDE)
Description
INFOID:0000000003935545
Detects front door LH open/close condition.
Component Function Check
INFOID:0000000003935546
1.
CHECK FUNCTION
1.
Select “DOOR SW-DR” in “Data monitor” mode with CONSULT-III.
2.
Check the front door switch LH signal under the following conditions.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Perform diagnosis procedure. Refer to
.
Diagnosis Procedure
INFOID:0000000003935547
1.
CHECK FRONT DOOR SWITCH LH CIRCUIT
1.
Disconnect BCM.
2.
Check continuity between BCM connector and front door switch
LH connector.
3.
Check continuity between BCM connector and ground.
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Repair or replace harness.
2.
CHECK FRONT DOOR SWITCH LH
ADP-65, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Replace front door switch LH.
3.
CHECK INTERMITTENT INCIDENT
GI-49, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-59, "Removal and Installation"
NO
>> Repair or replace the malfunctioning part.
Component Inspection
INFOID:0000000003935548
1.
CHECK FRONT DOOR SWITCH LH
Monitor item
Condition
Status
DOOR SW-DR
Front door switch LH
Open
ON
Close
OFF
BCM connector
Terminal
Front door switch
LH connector
Terminal
Continuity
M19
47
B8
2
Yes
BCM connector
Terminal
Ground
Continuity
M19
47
No
LIIA1027E
2009 Pathfinder
ADP-66
< COMPONENT DIAGNOSIS >
FRONT DOOR SWITCH (DRIVER SIDE)
1.
Turn ignition switch OFF.
2.
Disconnect front door switch LH.
3.
Check continuity between front door switch LH terminals.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace front door switch LH.
Terminal
Condition
Continuity
Front door switch LH
2
Ground part of
door switch
Front door switch
LH
Pushed
No
Released
Yes
LIIA2377E
2009 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст