Nissan Pathfinder (2009 year). Manual — part 485
CLIP AND FASTENER
INT-9
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
SIIA0316E
2009 Pathfinder
INT-10
< SYMPTOM DIAGNOSIS >
CLIP AND FASTENER
SIIA0317E
2009 Pathfinder
PRECAUTIONS
INT-11
< PRECAUTION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000003937554
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
Precaution Necessary for Steering Wheel Rotation After Battery Disconnect
INFOID:0000000004412005
NOTE:
• This Procedure is applied only to models with Intelligent Key system and NATS (NISSAN ANTI-THEFT SYS-
TEM).
• Remove and install all control units after disconnecting both battery cables with the ignition knob in the
″
LOCK
″
position.
• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If DTC is detected, perform trouble diagnosis according to self-diagnostic results.
For models equipped with the Intelligent Key system and NATS, an electrically controlled steering lock mech-
anism is adopted on the key cylinder.
For this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock and
steering wheel rotation will become impossible.
If steering wheel rotation is required when battery power is interrupted, follow the procedure below before
starting the repair operation.
OPERATION PROCEDURE
1.
Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2.
Use the Intelligent Key or mechanical key to turn the ignition switch to the
″
ACC
″
position. At this time, the
steering lock will be released.
3.
Disconnect both battery cables. The steering lock will remain released and the steering wheel can be
rotated.
4.
Perform the necessary repair operation.
5.
When the repair work is completed, return the ignition switch to the
″
LOCK
″
position before connecting
the battery cables. (At this time, the steering lock mechanism will engage.)
6.
Perform a self-diagnosis check of all control units using CONSULT-III.
Service Notice
INFOID:0000000003937555
• When removing or installing various parts, place a cloth or padding on the vehicle body to prevent scratches.
• Handle trim, molding, instruments, grille, etc. carefully during removing or installing. Be careful not to soil or
damage them.
2009 Pathfinder
INT-12
< PRECAUTION >
PRECAUTIONS
• Apply sealing compound where necessary when installing parts.
• When applying sealing compound, be careful that the sealing compound does not protrude from parts.
• When replacing any metal parts (for example body outer panel, members, etc.), be sure to take rust preven-
tion measures.
2009 Pathfinder
PREPARATION
INT-13
< PREPARATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000003937556
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tool
INFOID:0000000003937557
Tool number
(Kent-Moore No.)
Tool name
Description
—
(J-39570)
Chassis ear
Locating the noise
—
(J-43980)
NISSAN Squeak and Rattle kit
Repairing the cause of noise
SBT839
SBT840
(Kent-Moore No.)
Tool name
Description
(J-39565)
Engine ear
Locating the noise
SIIA0995E
2009 Pathfinder
INT-14
< ON-VEHICLE REPAIR >
DOOR FINISHER
ON-VEHICLE REPAIR
DOOR FINISHER
Removal and Installation
INFOID:0000000003937558
FRONT DOOR
Removal
1.
Remove the power window switch assembly.
• Disconnect the harness connectors.
2.
Remove the pull handle escutcheon.
3.
Remove the pull handle cover and remove screw.
4.
Lift the armrest upward to release clips and remove armrest.
• Remove the screws behind armrest.
5.
Release the clips and remove the door finisher.
1.
Front door
2.
Mirror bolt cover LH
3.
Pull handle escutcheon
4.
Pull handle/lock lever assembly
5.
Pull handle cover
6.
Front door finisher LH
7.
Seat memory switch (if equipped)
8.
Power window/lock switch assembly 9.
Armrest
10. Front door handle bracket
A.
Clip C101
B.
Clip C205
AWJIA0049GB
2009 Pathfinder
DOOR FINISHER
INT-15
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
• Disconnect lock cable and handle cable from door handle assembly. Refer to
.
6.
Remove the memory seat switch (if equipped).
• Disconnect the harness connector.
7.
Remove the pull handle/lock lever assembly.
Installation
Installation is in the reverse order of removal.
REAR DOOR
Removal
1.
Remove the power window switch assembly.
• Disconnect the harness connector.
2.
Remove the pull handle cover.
• Remove the screw behind the pull handle cover.
3.
Remove the pull handle escutcheon.
4.
Lift upward to release clips and remove the armrest.
• Remove the screws behind armrest.
5.
Release the clips and remove the rear door finisher.
• Disconnect the rear door tweeter connector, then remove the rear door tweeter screws and remove the
rear door tweeter.
Installation
Installation is in the reverse order of removal.
1.
Rear door
2.
Rear door tweeter
3.
Pull handle/lock lever assembly
4.
Pull handle escutcheon
5.
Pull handle cover
6.
Metal clip
7.
Power window switch assembly
8.
Armrest
9.
Rear door finisher (RH shown)
10. Rear door handle bracket
A.
Clip C101
AWJIA0050GB
2009 Pathfinder
INT-16
< ON-VEHICLE REPAIR >
BODY SIDE TRIM
BODY SIDE TRIM
Component
INFOID:0000000003937559
CAUTION:
• Wrap the tip of flat-bladed screwdriver with a cloth when removing metal clips from finishers.
• When removing or installing body side welts, do not allow butyl seal to come in contact with pillar
finisher.
1.
Center pillar upper finisher
2.
Center pillar assist grip
3.
Rear door welt
4.
Rear kick plate
5.
Access cover (RH side only)
6.
Center pillar lower finisher
7.
Front kick plate
8.
Lower dash side finisher
9.
Front door welt
10. Front pillar lower finisher
11.
Front pillar upper finisher
12.
Front pillar assist grip
13. LH side demister grille
14.
Molded plastic clip
15.
Garnish
C.
Clip C101
D.
Clip C111
E.
Metal clip
⇐
Front
AWJIA0051GB
2009 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст