Nissan Pathfinder (2009 year). Manual — part 370
SPARK PLUG
EM-17
< ON-VEHICLE MAINTENANCE >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Checking and adjusting spark plug gap is not required between
change intervals.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Do not drop or shock spark plug.
Cleaner air pressure
: Less than 588 kPa (5.9 bar, 6 kg/cm
2
, 85 psi)
Cleaning time
: Less than 20 seconds
SMA806CA
Application
United States and Canada
Mexico
Make
NGK
Standard type
DILFR5A-11
PLFR5A-11
Gap (nominal)
1.1 mm ().043 in)
2009 Pathfinder
EM-18
< ON-VEHICLE MAINTENANCE >
[VQ40DE]
CAMSHAFT VALVE CLEARANCE
CAMSHAFT VALVE CLEARANCE
Valve Clearance
INFOID:0000000003939482
INSPECTION
NOTE:
Perform the following inspection after removal, installation or replacement of camshaft or valve-related parts,
or if there are unusual engine conditions due to changes in valve clearance over time (starting, idling, and/or
noise).
1.
Remove the engine room cover. Refer to
EM-24, "Removal and Installation"
2.
Remove the air cleaner and air duct assembly. Refer to
3.
Remove rocker covers (RH and LH banks). Refer to
EM-41, "Removal and Installation"
4.
Measure the valve clearance as follows:
a.
Set No. 1 cylinder at TDC of its compression stroke.
• Rotate crankshaft pulley clockwise to align timing mark (A)
(grooved line without color) with timing indicator (B).
• Make sure that intake and exhaust cam noses on No. 1 cylin-
der (engine front side of RH bank) are located as shown.
• If not, rotate crankshaft one revolution (360
°
) and align as
shown.
b.
Use feeler gauge, measure the clearance between valve lifter
and camshaft.
Valve clearance:
Unit: mm (in)
*: Approximately 80
°
C (176
°
F)
AWBIA0719ZZ
SEM418G
SEM139D
Cold
Hot * (reference data)
Intake
0.26 - 0.34 (0.010 - 0.013)
0.304 - 0.416 (0.012 - 0.016)
Exhaust
0.29 - 0.37 (0.011 - 0.015)
0.308 - 0.432 (0.012 - 0.017)
2009 Pathfinder
CAMSHAFT VALVE CLEARANCE
EM-19
< ON-VEHICLE MAINTENANCE >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Measure the valve clearances at locations marked “
×
” as
shown in the table below (locations indicated in the illustration)
with feeler gauge.
• No. 1 cylinder at compression TDC
c.
Rotate crankshaft by 240
°
clockwise (when viewed from engine
front) to align No. 3 cylinder at TDC of its compression stroke.
NOTE:
Crankshaft pulley bolt flange has a stamped line every 60
°
. They
can be used as a guide to rotation angle.
• Measure the valve clearances at locations marked “
×
” as
shown in the table below (locations indicated in the illustration)
with feeler gauge.
• No. 3 cylinder at compression TDC
Measuring position (RH bank)
No. 1 CYL.
No. 3 CYL.
No. 5 CYL.
No. 1 cylinder at
compression TDC
EXH
×
INT
×
Measuring position (LH bank)
No. 2 CYL.
No. 4 CYL.
No. 6 CYL.
No. 1 cylinder at
compression TDC
INT
×
EXH
×
PBIC2054E
PBIC2916E
Measuring position (RH bank)
No. 1 CYL.
No. 3 CYL.
No. 5 CYL.
No. 3 cylinder at
compression TDC
EXH
×
INT
×
Measuring position (LH bank)
No. 2 CYL.
No. 4 CYL.
No. 6 CYL.
No. 3 cylinder at
compression TDC
INT
×
EXH
×
PBIC2055E
2009 Pathfinder
EM-20
< ON-VEHICLE MAINTENANCE >
[VQ40DE]
CAMSHAFT VALVE CLEARANCE
d.
Rotate crankshaft by 240
°
clockwise (when viewed from engine
front) to align No. 5 cylinder at TDC of compression stroke.
• Measure the valve clearances at locations marked “
×
” as
shown in the table below (locations indicated in the illustration)
with feeler gauge.
• No. 5 cylinder at compression TDC
5.
For the measured value out of the standard, perform adjustment.
ADJUSTMENT
• Perform adjustment depending on selected head thickness of valve lifter.
1.
Measure the valve clearance.
2.
Remove camshaft. Refer to
EM-81, "Removal and Installation"
.
3.
Remove valve lifters at the locations that are out of the standard.
4.
Measure the center thickness of removed valve lifters with
micrometer.
5.
Use the equation below to calculate valve lifter thickness for replacement.
PBIC2916E
Measuring position (RH bank)
No. 1 CYL.
No. 3 CYL.
No. 5 CYL.
No. 5 cylinder at
compression TDC
EXH
×
INT
×
Measuring position (LH bank)
No. 2 CYL.
No. 4 CYL.
No. 6 CYL.
No. 5 cylinder at
compression TDC
INT
×
EXH
×
PBIC2056E
KBIA0057E
2009 Pathfinder
CAMSHAFT VALVE CLEARANCE
EM-21
< ON-VEHICLE MAINTENANCE >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Thickness of new valve lifter can be identified by stamp marks
on the reverse side (inside the cylinder).
Intake
Available thickness of valve lifter: 27 sizes with range 7.88 to 8.40 mm (0.3102 to 0.3307 in) in steps of
0.02 mm (0.0008 in) (when manufactured at factory). Refer to
.
Exhaust
Available thickness of valve lifter: 25 sizes with range 7.88 to 8.36 mm (0.3102 to 0.3291 in) in steps of
0.02 mm (0.0008 in) (when manufactured at factory). Refer to
.
CAUTION:
Install identification letter at the end and top, “U” and “N”, at each of proper positions. (Be care-
ful of mis-installation between intake and exhaust.)
6.
Install selected valve lifter.
7.
Install camshaft. Refer to
EM-81, "Removal and Installation"
.
8.
Manually turn crankshaft pulley a few turns.
9.
Make sure that the valve clearances for cold engine are within the specifications by referring to the speci-
fied values.
10. Installation of the remaining components is in the reverse order of removal.
11. Start the engine, and check for unusual noise and vibration.
Valve lifter thickness calculation:
t = t
1
+ (C
1
– C
2
)
t
= Valve lifter thickness to be replaced
t
1
= Removed valve lifter thickness
C
1
= Measured valve clearance
C
2
= Standard valve clearance:
Intake
: 0.26 - 0.34 mm (0.010 - 0.013 in)*
Exhaust
: 0.29 - 0.37 mm (0.011 - 0.015 in)*
*: Approximately 20
°
C (68
°
F)
KBIA0119E
Stamp mark
Thickness
788U
7.88 mm (0.3102 in)
790U
7.90 mm (0.3110 in)
·
·
·
·
840U
8.40 mm (0.3307 in)
Stamp mark
Thickness
N788
7.88 mm (0.3102 in)
N790
7.90 mm (0.3110 in)
·
·
·
·
N836
8.36 mm (0.3291 in)
2009 Pathfinder
EM-22
< ON-VEHICLE MAINTENANCE >
[VQ40DE]
COMPRESSION PRESSURE
COMPRESSION PRESSURE
Compression Pressure
INFOID:0000000003939483
CHECKING COMPRESSION PRESSURE
1.
Warm up engine thoroughly.
2.
Release fuel pressure. Refer to
.
3.
Disconnect fuel pump fuse to avoid fuel injection during mea-
surement.
4.
Remove intake manifold collector. Refer to
EM-26, "Removal and Installation"
5.
Remove spark plug from each cylinder. Refer to
EM-16, "Removal and Installation"
6.
Connect engine tachometer (not required in use of CONSULT-III).
7.
Install compression tester with adapter onto spark plug hole.
• Use compression gauge whose pick up end inserted to spark
plug hole is smaller than 20 mm (0.79 in) in diameter. Other-
wise, it may be caught by cylinder head during removal.
8.
Turn ignition switch to “START” for cranking. When the gauge pointer stabilizes, read the compression
pressure and engine rpm. Perform these steps to check each cylinder.
Compression pressure:
Unit: kPa (kg/cm
2
, psi) /rpm
CAUTION:
Always use a fully charged battery to obtain specified engine speed.
• If the engine speed is out of the specified range, check the battery liquid for proper gravity. Check the
engine speed again with normal battery gravity.
BBIA0534E
PBIC0900E
SBIA0533E
Standard
Minimum
Differential limit between cylinders
1,275 (13.0, 185) / 300
981 (10.0, 142) / 300
98 (1.0, 14) / 300
2009 Pathfinder
COMPRESSION PRESSURE
EM-23
< ON-VEHICLE MAINTENANCE >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• If the compression pressure is below the minimum value, check the valve clearances and parts associ-
ated with the combustion chamber (valve, valve seat, piston, piston ring, cylinder bore, cylinder head,
cylinder head gasket). After checking, measure the compression pressure again.
• If some cylinders have low compression pressure, pour a small amount of engine oil into the spark plug
hole of the cylinder to re-check it for compression.
• If the added engine oil improves the compression, piston rings may be worn out or damaged. Check the
piston rings and replace if necessary.
• If the compression pressure remains at low level despite the addition of engine oil, the valves may be
malfunctioning. Check the valves for damage. Replace the valve or valve seat accordingly.
• If two adjacent cylinders have respectively low compression pressure and their compression remains
low even after the addition of engine oil, cylinder head gaskets may be leaking, or a valve in adjacent
cylinders may be damaged. Inspect and repair as required.
9.
Install the components in the reverse order of removal.
10. Start the engine, and confirm that it runs smoothly.
11. Perform trouble diagnosis. If DTC appears, erase it. Refer to
.
2009 Pathfinder
EM-24
< ON-VEHICLE REPAIR >
[VQ40DE]
ENGINE ROOM COVER
ON-VEHICLE REPAIR
ENGINE ROOM COVER
Removal and Installation
INFOID:0000000003939484
CAUTION:
Do not damage or scratch cover when installing or removing.
REMOVAL
1.
Remove the engine room cover bolts using power tool.
2.
Lift up on engine cover firmly to dislodge snap fit mounts.
INSTALLATION
Installation is in the reverse order of removal.
WBIA0622E
2009 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст