Murano Cross Cabriolet Z51 (2013 year). Manual — part 88
B1082 SEAT BELT PRE-TENSIONER RH
SRC-73
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1082 SEAT BELT PRE-TENSIONER RH
DTC Logic
INFOID:0000000008461828
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000008461829
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE SEAT BELT PRE-TENSIONER
1.
Replace seat belt pre-tensioner RH. Refer to
.
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1082
PRE-TEN FRONT RH
[VB-SHORT]
Seat belt pre-tensioner RH circuit is
shorted to power supply circuit
• Harness or connectors
(The pre-tensioner circuit is shorted.)
• Malfunction in seat belt pre-tensioner RH
• Malfunction in air bag diagnosis sensor unit
Revision: 2012 October
2013 Murano CrossCabriolet
SRC-74
< DTC/CIRCUIT DIAGNOSIS >
B1082 SEAT BELT PRE-TENSIONER RH
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2012 October
2013 Murano CrossCabriolet
B1083 SEAT BELT PRE-TENSIONER RH
SRC-75
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1083 SEAT BELT PRE-TENSIONER RH
DTC Logic
INFOID:0000000008461830
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000008461831
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE SEAT BELT PRE-TENSIONER
1.
Replace seat belt pre-tensioner RH. Refer to
.
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1083
PRE-TEN FRONT RH
[GND-SHORT]
Seat belt pre-tensioner RH circuit is
shorted to ground
• Harness or connectors
(The pre-tensioner circuit is shorted.)
• Malfunction in seat belt pre-tensioner RH
• Malfunction in air bag diagnosis sensor unit
Revision: 2012 October
2013 Murano CrossCabriolet
SRC-76
< DTC/CIRCUIT DIAGNOSIS >
B1083 SEAT BELT PRE-TENSIONER RH
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2012 October
2013 Murano CrossCabriolet
B1084 SEAT BELT PRE-TENSIONER RH
SRC-77
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1084 SEAT BELT PRE-TENSIONER RH
DTC Logic
INFOID:0000000008461832
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000008461833
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE SEAT BELT PRE-TENSIONER
1.
Replace seat belt pre-tensioner RH. Refer to
.
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1084
PRE-TEN FRONT RH
[SHORT]
Seat belt pre-tensioner RH circuits are
shorted to each other
• Harness or connectors
(The pre-tensioner circuit is shorted.)
• Malfunction in seat belt pre-tensioner RH
• Malfunction in air bag diagnosis sensor unit
Revision: 2012 October
2013 Murano CrossCabriolet
SRC-78
< DTC/CIRCUIT DIAGNOSIS >
B1084 SEAT BELT PRE-TENSIONER RH
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2012 October
2013 Murano CrossCabriolet
B1086 SEAT BELT PRE-TENSIONER LH
SRC-79
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1086 SEAT BELT PRE-TENSIONER LH
DTC Logic
INFOID:0000000008461834
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000008461835
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE SEAT BELT PRE-TENSIONER
1.
Replace seat belt pre-tensioner LH. Refer to
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1086
PRE-TEN FRONT LH
[OPEN]
Seat belt pre-tensioner LH circuit is open
• Harness or connectors
(The pre-tensioner circuit is open.)
• Malfunction in seat belt pre-tensioner LH
• Malfunction in air bag diagnosis sensor unit
Revision: 2012 October
2013 Murano CrossCabriolet
SRC-80
< DTC/CIRCUIT DIAGNOSIS >
B1086 SEAT BELT PRE-TENSIONER LH
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2012 October
2013 Murano CrossCabriolet
B1087 SEAT BELT PRE-TENSIONER LH
SRC-81
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1087 SEAT BELT PRE-TENSIONER LH
DTC Logic
INFOID:0000000008461836
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000008461837
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE SEAT BELT PRE-TENSIONER
1.
Replace seat belt pre-tensioner LH. Refer to
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1087
PRE-TEN FRONT LH
[VB-SHORT]
Seat belt pre-tensioner LH circuit is
shorted to power supply circuit
• Harness or connectors
(The pre-tensioner circuit is shorted.)
• Malfunction in seat belt pre-tensioner LH
• Malfunction in air bag diagnosis sensor unit
Revision: 2012 October
2013 Murano CrossCabriolet
SRC-82
< DTC/CIRCUIT DIAGNOSIS >
B1087 SEAT BELT PRE-TENSIONER LH
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2012 October
2013 Murano CrossCabriolet
B1088 SEAT BELT PRE-TENSIONER LH
SRC-83
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1088 SEAT BELT PRE-TENSIONER LH
DTC Logic
INFOID:0000000008461838
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000008461839
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE SEAT BELT PRE-TENSIONER
1.
Replace seat belt pre-tensioner LH. Refer to
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1088
PRE-TEN FRONT LH
[GND-SHORT]
Seat belt pre-tensioner LH circuit is
shorted to ground
• Harness or connectors
(The pre-tensioner circuit is shorted.)
• Malfunction in seat belt pre-tensioner LH
• Malfunction in air bag diagnosis sensor unit
Revision: 2012 October
2013 Murano CrossCabriolet
SRC-84
< DTC/CIRCUIT DIAGNOSIS >
B1088 SEAT BELT PRE-TENSIONER LH
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2012 October
2013 Murano CrossCabriolet
B1089 SEAT BELT PRE-TENSIONER LH
SRC-85
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1089 SEAT BELT PRE-TENSIONER LH
DTC Logic
INFOID:0000000008461840
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000008461841
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE SEAT BELT PRE-TENSIONER
1.
Replace seat belt pre-tensioner LH. Refer to
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1089
PRE-TEN FRONT LH
[SHORT]
Seat belt pre-tensioner LH circuits are
shorted to each other
• Harness or connectors
(The pre-tensioner circuit is shorted.)
• Malfunction in seat belt pre-tensioner LH
• Malfunction in air bag diagnosis sensor unit
Revision: 2012 October
2013 Murano CrossCabriolet
SRC-86
< DTC/CIRCUIT DIAGNOSIS >
B1089 SEAT BELT PRE-TENSIONER LH
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2012 October
2013 Murano CrossCabriolet
B1090, B1091, B1092, B1093, B1094, B1095 DIAGNOSIS SENSOR UNIT
SRC-87
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1090, B1091, B1092, B1093, B1094, B1095 DIAGNOSIS SENSOR UNIT
DTC Logic
INFOID:0000000008461842
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000008461843
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connectors.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1090
B1091
B1092
B1093
B0194
B1095
CONTROL UNIT
Air bag diagnosis sensor unit is malfunctioning
Malfunction in air bag diagnosis sensor unit
Revision: 2012 October
2013 Murano CrossCabriolet
SRC-88
< DTC/CIRCUIT DIAGNOSIS >
B1106, B1107, B1108, B1109, B1110, B1111 DIAGNOSIS SENSOR UNIT
B1106, B1107, B1108, B1109, B1110, B1111 DIAGNOSIS SENSOR UNIT
DTC Logic
INFOID:0000000008461844
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000008461845
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connectors.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1106
B1107
B1108
B1109
B1110
B1111
CONTROL UNIT
Air bag diagnosis sensor unit is malfunctioning
Malfunction in air bag diagnosis sensor unit
Revision: 2012 October
2013 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст