Murano Cross Cabriolet Z51 (2013 year). Manual — part 54
IP-8
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000008462958
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Service Procedure Precautions for Models with a Pop-up Roll Bar
INFOID:0000000008462959
WARNING:
Always observe the following items for preventing accidental activation.
• Risk of passenger injury or death may increase if the pop-up roll bar does not deploy during a roll
over collision. In order to reduce the chance of an incident where the pop-up roll bar is inoperative,
all maintenance must be performed by a NISSAN or INFINITI dealer.
• Before removing and installing the pop-up roll bar component parts and harness, always turn the
ignition switch OFF, disconnect the battery negative terminal, and wait for 3 minutes or more. (The
purpose of this operation is to discharge electricity that is accumulated in the auxiliary power supply
circuit in the air bag diagnosis sensor unit.)
• When repairing, removing, and installing a pop-up roll bar, always refer to SRS AIR BAG and SRS
AIR BAG CONTROL warnings in the Service Manual.
Precaution
INFOID:0000000008462960
• Disconnect battery negative terminal in advance.
• Disconnect air bag system line in advance.
• Never tamper with or force air bag lid open, as this may adversely affect air bag performance.
• Be careful not to scratch pad and other parts.
• When removing or disassembling any part, be careful not to damage or deform it. Protect parts, which may
get in the way with a shop cloth.
• When removing parts with a screwdriver or other tool, cover the tool surface by vinyl tape to protect parts.
• Keep removed parts protected with a shop cloth.
• If a clip is deformed or damaged, replace it.
Revision: 2012 October
2013 Murano CrossCabriolet
PRECAUTIONS
IP-9
< PRECAUTION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
• If an unreusable part is removed, replace it with a new one.
• Tighten bolts and nuts firmly to the specified torque.
• After reassembly has been completed, make sure each part functions correctly.
• Remove stains in the following way.
Water-soluble stains:
Dip a soft cloth in warm water, and then squeeze it tightly. After wiping the stain, wipe with a soft dry cloth.
Oil stain:
Dissolve a synthetic detergent in warm water (density of 2 to 3%), dip the cloth, then clean off the stain with
the cloth. Next, dip the cloth in fresh water and squeeze it tightly. Then clean off the detergent completely.
Then wipe the area with a soft dry cloth.
• Never use any organic solvent, such as thinner or benzine.
Revision: 2012 October
2013 Murano CrossCabriolet
IP-10
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000008462961
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
INFOID:0000000008462962
Tool number
(Kent-Moore No.)
Tool name
Description
(J-39570)
Chassis ear
Locates the noise
(J-43980)
NISSAN Squeak and Rattle
Kit
Repairs the cause of noise
SIIA0993E
SIIA0994E
Tool name
Description
Engine ear
Locates the noise
Remover tool
Removes clips, pawls, and metal clips
SIIA0995E
JMKIA3050ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
CLIP LIST
IP-11
< PREPARATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
CLIP LIST
Clip List
INFOID:0000000008462963
JMJIA3734GB
Revision: 2012 October
2013 Murano CrossCabriolet
IP-12
< REMOVAL AND INSTALLATION >
INSTRUMENT PANEL ASSEMBLY
REMOVAL AND INSTALLATION
INSTRUMENT PANEL ASSEMBLY
Exploded View
INFOID:0000000008462964
JMJIA4610GB
Revision: 2012 October
2013 Murano CrossCabriolet
INSTRUMENT PANEL ASSEMBLY
IP-13
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
Removal and Installation
INFOID:0000000008462965
WORK STEP
When removing instrument panel assembly, combination meter, AV control unit (or audio unit), and front dis-
play unit take steps in the order shown by the number below.
1.
Speaker grille RH
2.
Center speaker grille
3.
Speaker grille LH
4.
Front squawker LH
5.
Instrument side finisher LH
6.
Switch bracket
7.
Instrument lower panel LH
8.
Fuse block lid
9.
Steering column lower cover
10. Cluster lid C
11.
Cluster lid C (lower)
12. Illumination lamp
13. Socket and bulb
14. Glove box striker RH
15. Instrument lower panel RH
16. Socket and bulb
17. Glove box lamp
18. Glove box dumper
19. Instrument side finisher RH
20. Instrument panel assembly
21. Front squawker RH
22. Optical sensor
23. Center speaker
24. Sunload sensor
25. Security indicator
26. Combination meter
27. Cluster lid A
28. Steering column upper cover
29. Instrument stay cover LH
30. Instrument stay cover RH
31. Glove box lid
32. Passenger air bag module
33. Display unit
34. AV control unit
35. Cluster lid D
36. Glove box striker LH
37. Center ventilator assembly
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
PARTS
INSTRUMENT
PANEL ASSEMBLY
COMBINATION
METER
AV CONTROL
UNIT
(or AUDIO UNIT)
DISPLAY UNIT (or
AUDIO DISPLAY
UNIT)
Instrument side finisher LH
[1]
[1]
Front body side welt LH
[2]
Front pillar garnish LH
[3]
Speaker grille LH
[4]
Front squawker LH
[5]
Vehicle security indicator
[6]
Sunload sensor
[7]
Instrument lower panel LH
[8]
[2]
Driver air bag module
[9]
Steering wheel
[10]
Steering column cover
[11]
[3]
Combination switch
[12]
Spiral cable
[13]
Cluster lid A
[14]
[4]
Combination meter
[15]
[5]
Cluster lid C (lower)
[16]
Instrument stay cover LH
[17]
[1]
[1]
Instrument stay cover RH
[18]
[2]
[2]
Cluster lid D
[19]
[3]
[3]
Cluster lid C
[20]
[4]
[4]
AV control unit
[21]
[5]
[5]
Center ventilator assembly
[22]
[6]
Display unit
[23]
[7]
Revision: 2012 October
2013 Murano CrossCabriolet
IP-14
< REMOVAL AND INSTALLATION >
INSTRUMENT PANEL ASSEMBLY
[ ]: Number indicates step in removal procedures.
WARNING:
Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes or
more.
CAUTION:
When removing, always use a remover tool that is made of plastic.
REMOVAL
1.
Remove instrument side finisher LH.
1.
Insert a remover tool (A) into lower space.
2.
Pull the instrument side finisher LH (1) crosswise.
2.
Remove front body side welt LH. Refer to
INT-21, "BODY SIDE WELT : Removal and Installation"
3.
Remove front pillar garnish LH. Refer to
INT-18, "FRONT PILLAR GARNISH : Removal and Installation"
.
4.
Remove speaker grille LH.
1.
Pull up speaker grille LH (1) to disengage pawls.
2.
Remove speaker grille LH.
5.
Remove front squawker LH. Refer to
AV-106, "Removal and Installation"
.
6.
Remove vehicle security indicator. Refer to
SEC-111, "Removal and Installation"
7.
Remove sunload sensor. Refer to
HAC-82, "Removal and Installation"
Center speaker grille
[24]
Center speaker (BOSE audio with NAVI mod-
els)
[25]
Instrument side finisher RH
[26]
Front body side welt RH
[27]
Front pillar garnish RH
[28]
Speaker grille RH
[29]
Front squawker RH
[30]
Optical sensor (XENON headlamp models)
[31]
Instrument lower panel RH
[32]
Passenger air bag module harness connector
[33]
Passenger air bag module mounting bolt
[34]
Instrument panel assembly
[35]
: Pawl
JMJIA1314ZZ
: Pawl
JMJIA1315ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
INSTRUMENT PANEL ASSEMBLY
IP-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
8.
Remove instrument lower panel LH.
1.
Remove hood opener lever fixing bolts (A).
2.
Pull back instrument lower panel LH (1).
3.
Release data link connector (pawl) then remove it from
instrument lower panel LH.
4.
Disconnect harness connectors and aspirator duct.
9.
Remove driver air bag module. Refer to
SR-11, "Removal and Installation"
.
10. Remove steering wheel. Refer to
ST-30, "Removal and Installation"
.
11. Remove steering column covers.
1.
Remove steering column cover fixing screws (A).
2.
Pull up steering column upper cover (1), and then remove
steering column upper cover.
3.
Pull down steering column lower cover (2), and then remove
steering column lower cover.
12. Remove combination switch. Refer to
BCS-78, "Removal and Installation"
13. Remove spiral cable. Refer to
SR-14, "Removal and Installation"
.
14. Remove cluster lid A.
1.
Pull back cluster lid A (1), and disengage clips and pawl.
2.
Remove cluster lid A.
15. Remove combination meter. Refer to
MWI-70, "Removal and Installation"
: Clip
: Metal clip
JMJIA1316ZZ
: Pawl
JMJIA1317ZZ
: Clip
: Pawl
JMJIA1318ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
IP-16
< REMOVAL AND INSTALLATION >
INSTRUMENT PANEL ASSEMBLY
16. Remove cluster lid C (lower).
1.
Disengage cluster lid C (lower) (1) fixing clips and pawls
with remover tool (A).
2.
Pull down cluster lid C (lower).
3.
Disconnect illumination lamp harness connector.
17. Remove instrument stay cover LH.
1.
Remove instrument stay cover LH (1) fixing screw (A).
2.
Disengage instrument stay cover LH fixing clips and pawls
with remover tool.
3.
Pull back and pull up instrument stay cover LH.
4.
Disconnect push button ignition switch harness connector
18. Remove instrument stay cover RH.
1.
Remove instrument stay cover RH (1) fixing screw (A).
2.
Disengage instrument stay cover RH fixing clips and pawls
with remover tool.
3.
Pull back and pull up instrument stay cover RH.
4.
Disconnect hazard switch harness connector.
19. Remove cluster lid D.
1.
Remove cluster lid D (1) fixing screws (A).
2.
Pull back cluster lid D.
3.
Disconnect harness connector.
20. Remove cluster lid C.
1.
Remove cluster lid C (1) fixing screws (A).
2.
Pull back cluster lid C.
3.
Disconnect harness connectors.
: Clip
: Pawl
JMJIA1319ZZ
: Clip
: Pawl
JMJIA1320ZZ
: Clip
: Pawl
JMJIA1321ZZ
: Pawl
JMJIA1322ZZ
JMJIA1323ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
INSTRUMENT PANEL ASSEMBLY
IP-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
21. Remove AV control unit. Refer to
AV-102, "Removal and Installation"
22. Remove center ventilator assembly.
1.
Remove center ventilator assembly (1) fixing screws (A).
2.
Pull back center ventilator assembly.
23. Remove display unit. Refer to
AV-104, "Removal and Installation"
.
24. Remove center speaker grille.
1.
Disengage center speaker grille (1) fixing clips with remover
tool (A).
2.
Pull up center speaker grille.
25. Remove center speaker (BOSE audio with NAVI models). Refer to
AV-242, "Removal and Installation"
26. Remove instrument side finisher RH.
1.
Insert a remover tool (A) into lower space.
2.
Pull the instrument side finisher RH (1) crosswise.
27. Remove front body side welt RH. Refer to
INT-21, "BODY SIDE WELT : Removal and Installation"
.
28. Remove front pillar garnish RH. Refer to
INT-18, "FRONT PILLAR GARNISH : Removal and Installation"
29. Remove speaker grille RH.
Pull up speaker grille RH (1).
30. Remove front squawker RH. Refer to
AV-106, "Removal and Installation"
31. Remove optical sensor (XENON headlamp models). Refer to
EXL-75, "Removal and Installation"
.
: Clip
: Pawl
JMJIA1325ZZ
: Clip
JMJIA1327ZZ
: Pawl
JMJIA1328ZZ
: Pawl
JMJIA1329ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
IP-18
< REMOVAL AND INSTALLATION >
INSTRUMENT PANEL ASSEMBLY
32. Remove instrument lower panel RH.
1.
Remove instrument lower panel RH (1) fixing screws (A).
2.
Open the glove box lid (2).
3.
Remove instrument lower panel RH fixing screws (B).
4.
Pull back instrument lower panel RH.
5.
Disconnect harness connector.
33. Disconnect front passenger air bag module connector. Refer to
SR-17, "Removal and Installation"
34. Remove front passenger air bag module fixing bolt. Refer to
35. Remove instrument panel assembly (1) mounting screws (A) and bolt (B).
36. Remove instrument panel assembly.
CAUTION:
• Cover center console upper surface with a shop cloth to prevent it from being damaged.
• When removing instrument panel assembly, 2 workers are required so as to prevent it from drop-
ping.
37. Remove the following parts after removing instrument panel assembly.
• Passenger air bag module. Refer to
SR-17, "Removal and Installation"
.
• Ventilator duct. Refer to
VTL-10, "SIDE VENTILATOR GRILLE : Removal and Installation"
• Upper ventilator duct. Refer to
VTL-11, "UPPER VENTILATOR DUCT : Removal and Installation"
.
• Defroster nozzle and side defroster nozzle LH/RH. Refer to
VTL-11, "DEFROSTER NOZZLE AND SIDE
DEFROSTER NOZZLE : Removal and Installation"
.
• Side defroster grille LH/RH. Refer to
VTL-10, "SIDE DEFROSTER GRILLE : Removal and Installation"
• Side ventilator grille LH/RH. Refer to
VTL-10, "SIDE VENTILATOR GRILLE : Removal and Installation"
• Antenna feeder
: Pawl
: Metal clip
JMJIA1330ZZ
JMJIA1331ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
INSTRUMENT PANEL ASSEMBLY
IP-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
- BOSE audio without navigation: Refer to
- BOSE audio with navigation: Refer to
.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Never use the steering wheel mounting nut after removal, replace with the new nut.
• Never use the driver air bag mounting bolts after removal, replace with the new bolts.
• Never use the passenger air bag mounting bolt after removal, replace with the new bolt.
Revision: 2012 October
2013 Murano CrossCabriolet
IP-20
< REMOVAL AND INSTALLATION >
CENTER CONSOLE ASSEMBLY
CENTER CONSOLE ASSEMBLY
Exploded View
INFOID:0000000008462966
1.
Instrument lower cover RH
2.
Instrument lower cover LH
3.
Instrument stay
4.
Front console bracket
5.
Console reinforcement
6.
Lower console finisher LH
7.
Console harness
8.
Inside key antenna
9.
Console rear finisher
10. Center console assembly
11.
Socket and bulb
12. Console finisher assembly
13. Cup holder assembly
14. Console pocket
15. Socket knob
16. Socket inner case
17. Console mat
18. Console switch finisher
19. Front console pocket
20. Lower console finisher RH
21. USB connector
22. Socket knob
23. Socket ring
24. Socket inner case
25. Lower console assembly
26. Auxiliary input jack
: Pawl
: Clip
: Metal clip
JMJIA6324ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
CENTER CONSOLE ASSEMBLY
IP-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
Removal and Installation
INFOID:0000000008462967
CAUTION:
When removing, always use a remover tool that is made of plastic.
REMOVAL
1.
Remove selector lever knob. Refer to
TM-145, "Removal and Installation"
.
2.
Remove console finisher assembly.
1.
Open the console lid.
2.
Remove console finisher assembly (1) fixing pawls and
metal clips with remover tool (A).
3.
Pull up console finisher assembly.
4.
Disconnect harness connectors.
3.
Remove front console pocket.
1.
Remove front console pocket (1) fixing screw (A).
2.
Pull up front console pocket, and then disengage metal
clips.
3.
Disconnect harness connectors.
4.
Remove console rear finisher.
1.
Pull back console rear finisher.
2.
Disconnect harness connector.
5.
Remove center console assembly.
1.
Remove center console assembly (1) fixing screws (A).
2.
Lift up back side and pull back.
: Pawl
: Metal clip
JMJIA1334ZZ
: Metal clip
JMJIA1335ZZ
: Metal clip
JMJIA6325ZZ
JMJIA1338ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
IP-22
< REMOVAL AND INSTALLATION >
CENTER CONSOLE ASSEMBLY
6.
Remove instrument lower cover LH and RH.
1.
Disengage instrument lower cover LH (1) fixing pawls and
clips.
2.
Pull back instrument lower cover LH.
3.
Disengage instrument lower cover RH (2) fixing pawls and
clips.
4.
Pull the instrument lower cover RH crosswise.
7.
Remove lower console finisher LH and RH.
1.
Remove lower console finisher LH (1) fixing screws (A).
2.
Remove lower console finisher LH fixing clip (B).
3.
Remove lower console finisher LH fixing clip (C).
4.
Pull the console finisher LH crosswise.
5.
Remove lower console finisher RH (2) fixing screws (D).
6.
Remove lower console finisher RH fixing clip (E).
7.
Remove lower console finisher RH fixing clip (F).
8.
Pull the console finisher RH crosswise.
8.
Remove lower console assembly.
1.
Remove lower console assembly (1) fixing screws (A).
2.
Remove lower console assembly mounting bolts (B).
3.
Disconnect harness connectors.
NOTE:
Remove following parts after removing lower console assembly.
• USB connector: Refer to
AV-114, "Removal and Installation"
.
• Auxiliary input jacks: Refer to
AV-113, "Removal and Installation"
.
• Console power socket: Refer to
PWO-4, "CONSOLE POWER SOCKET : Removal and Installation"
9.
Remove CVT shift selector. Refer to
TM-145, "Removal and Installation"
.
10. Remove console reinforcement.
1.
Remove console reinforcement (1) mounting nut (A).
2.
Remove console reinforcement mounting bolts (B).
3.
Remove harness clips.
11. Remove instrument stay mounting nuts, and then remove instrument stay.
12. Remove front console bracket mounting bolt and nut, and then remove front console bracket.
INSTALLATION
Install in the reverse order of removal.
: Clip
: Pawl
JMJIA1339ZZ
: Clip
JMJIA1340ZZ
JMJIA1341ZZ
: Clip
JMJIA1342ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
LAN
LAN-1
ELECTRICAL & POWER CONTROL
C
D
E
F
G
H
I
J
K
L
B
SECTION
LAN
A
O
P
N
CONTENTS
LAN SYSTEM
CAN FUNDAMENTAL
HOW TO USE THIS MANUAL . . . . . ..
HOW TO USE THIS SECTION . . . . . . .
Information . . . . . . . . . . . . . . . ....
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precautions for Trouble Diagnosis . . . . . . ....
Precautions for Harness Repair . . . . . . . ....
SYSTEM DESCRIPTION . . . . . . . ..
SYSTEM . . . . . . . . . . . . . . . ..
CAN COMMUNICATION SYSTEM . . . . . . .....
CAN COMMUNICATION SYSTEM : System De-
scription . . . . . . . . . . . . . . . . .....
DIAG ON CAN . . . . . . . . . . . . . . .....
DIAG ON CAN : System Description . . . . . ....
TROUBLE DIAGNOSIS . . . . . . . . . ..
Component Description . . . . . . . . . . .....
Condition of Error Detection . . . . . . . . . ..
Symptom When Error Occurs in CAN Communi-
cation System . . . . . . . . . . . . . . ....
CAN Diagnosis with CONSULT . . . . . . . ..
Self-Diagnosis . . . . . . . . . . . . . . .
CAN Diagnostic Support Monitor . . . . . . .
How to Use CAN Communication Signal Chart . ..
BASIC INSPECTION . . . . . . . . ...
DIAGNOSIS AND REPAIR WORKFLOW . . .
Trouble Diagnosis Flow Chart . . . . . . . . .
Trouble Diagnosis Procedure . . . . . . . . ..
CAN
HOW TO USE THIS MANUAL . . . . . .
HOW TO USE THIS SECTION . . . . . . .
Information . . . . . . . . . . . . . . . ...
Abbreviation List . . . . . . . . . . . . . ..
PRECAUTION . . . . . . . . . . . ..
PRECAUTIONS . . . . . . . . . . . . .
Service Procedure Precautions for Models with a
Pop-up Roll Bar . . . . . . . . . . . . . ...
Precaution for Battery Service . . . . . . . . .
Precautions for Trouble Diagnosis . . . . . . ..
Precautions for Harness Repair . . . . . . . ..
SYSTEM DESCRIPTION . . . . . . . .
COMPONENT PARTS . . . . . . . . . ..
Component Parts Location . . . . . . . . . ..
SYSTEM . . . . . . . . . . . . . . .
CAN COMMUNICATION SYSTEM . . . . . . .
CAN COMMUNICATION SYSTEM : System De-
scription . . . . . . . . . . . . . . . . ...
CAN COMMUNICATION SYSTEM : CAN Com-
munication Control Circuit . . . . . . . . . ...
CAN COMMUNICATION SYSTEM : CAN System
Specification Chart . . . . . . . . . . . . ..
CAN COMMUNICATION SYSTEM : CAN Com-
munication Signal Chart . . . . . . . . . . ..
WIRING DIAGRAM . . . . . . . . . ..
CAN SYSTEM . . . . . . . . . . . . ...
Wiring Diagram . . . . . . . . . . . . . .
BASIC INSPECTION . . . . . . . . ...
DIAGNOSIS AND REPAIR WORKFLOW . .
Interview Sheet . . . . . . . . . . . . . .
Revision: 2012 October
2013 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст