Murano Cross Cabriolet Z51 (2013 year). Manual — part 13
BCS
CONFIGURATION (BCM)
BCS-63
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
CONFIGURATION (BCM)
Description
INFOID:0000000008460436
Vehicle specification needs to be written with CONSULT because it is not written after replacing BCM.
Configuration has three functions as follows.
NOTE:
Manual setting item: Items which need selection by vehicle specifications
Automatic setting item: Items which are written in automatically (Setting can not be changed)
For some models and specifications, the automatic setting item may not be displayed.
CAUTION:
When replacing BCM, always perform “WRITE CONFIGURATION” with CONSULT. Or not doing so,
BCM control function does not operate normally.
• Complete the procedure of “WRITE CONFIGURATION” in order.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
• Never perform “WRITE CONFIGURATION” except for new BCM.
• If you set incorrect “WRITE CONFIGURATION”, incidents might occur.
Work Procedure
INFOID:0000000008460437
1.
WRITING MODE SELECTION
CONSULT Configuration
Select “CONFIGURATION” of BCM.
When writing saved data>>GO TO 2.
When writing manually>>GO TO 3.
2.
PERFORM “WRITE CONFIGURATION - CONFIG FILE”
CONSULT Configuration
Perform “WRITE CONFIGURATION - Config file”.
>> WORK END
3.
PERFORM “WRITE CONFIGURATION - MANUAL SELECTION”
CONSULT Configuration
1.
Select "WRITE CONFIGURATION - Manual selection".
2.
Identify the correct model and configuration list. Refer to
.
3.
Confirm and/or change setting value for each item.
CAUTION:
Thoroughly read and understand the vehicle specification. ECU control may not operate normally
if the setting is not correct.
NOTE:
If items are not displayed, touch “SETTING”. Refer to
for written items and
setting value.
4.
Select "SETTING".
CAUTION:
Make sure to select “SETTING” even if the indicated configuration of brand new BCM is same as
the desirable configuration. If not, configuration which is set automatically by selecting vehicle
model can not be memorized.
5.
When "COMMAND FINISHED", select "END".
Function
Description
READ CONFIGURATION
• Reads the vehicle configuration of current BCM.
• Saves the read vehicle configuration.
WRITE CONFIGURATION - Manual selection
Writes the vehicle configuration with manual selection.
WRITE CONFIGURATION - Config file
Writes the vehicle configuration with saved data.
Revision: 2012 October
2013 Murano CrossCabriolet
BCS-64
< BASIC INSPECTION >
CONFIGURATION (BCM)
>> GO TO 4.
4.
OPERATION CHECK
Confirm that each function controlled by BCM operates normally.
>> WORK END
Configuration list
INFOID:0000000008460438
CAUTION:
Thoroughly read and understand the vehicle specification. ECU control may not operate normally if
the setting is not correct.
MANUAL SETTING ITEM
NOTE
Items
Setting value
HANDLE
LHD
—
AUTO SETTING ITEM
NOTE
Items
Setting value
ROOF FUNCTION
W/ REQ SW
—
CONNECTION RECEIVER SET
MODE2
—
BATTERY SAVER FUNCTION
MODE3
—
TRANSIT MODE
WITH
—
ACC BAT SAVE FUNC
MODE2
—
DI LMP VARIAT
MODE4
—
LIGHT RECOG
MODE7
—
TRANSMISSION
AT with ABS
—
RAIN SENSOR CONFIG
WITHOUT
—
HAZARD SW TYPE
MODE1
—
BCM AC CONTROL
MODE1
—
TIRE PRESSURE
230kPa
—
Revision: 2012 October
2013 Murano CrossCabriolet
BCS
SHIPPING MODE CANCEL OPERATION
BCS-65
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
SHIPPING MODE CANCEL OPERATION
Description
INFOID:0000000008973700
SYSTEM DIAGRAM
DESCRIPTION
• The combination meter transmits meter CAN signal*
1
to BCM via CAN communication, when the extended
storage fuse switch is ON.
• BCM switches the status (shipping mode or normal mode) by itself according to the meter CAN signal*
1
from
combination meter, and transmits shipping mode status signal to combination meter via CAN communica-
tion.
• The combination meter displays extended storage fuse warning message*
2
on the information display, and
turns the turn signal indicator lamp (LH/RH) ON, when BCM is in shipping mode.
• BCM control function is limited in shipping mode. Refer to
.
*1: Odometer signal, wake up signal and each signal.
*2: When shipping mode function operates, “SHIPPING MODE ON PUSH STORAGE FUSE” is displayed.
Work Procedure
INFOID:0000000008973701
1.
SHIPPING MODE CANCEL OPERATION
1.
Turn ignition switch OFF.
2.
Push in (switch on) the extended storage fuse switch. Refer to
3.
Turn ignition switch ON.
4.
Turn ignition switch OFF and wait at least 2 seconds.
>> GO TO 2.
2.
SHIPPING MODE CANCEL CHECK
1.
Turn ignition switch ON.
2.
Check that extended storage fuse warning message is not displays on information display.
>> WORK END
JMMIA1345GB
Revision: 2012 October
2013 Murano CrossCabriolet
BCS-66
< DTC/CIRCUIT DIAGNOSIS >
U1000 CAN COMM
DTC/CIRCUIT DIAGNOSIS
U1000 CAN COMM
Description
INFOID:0000000008460441
CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Modern
vehicle is equipped with many electronic control unit, and each control unit shares information and links with
other control units during operation (not independent). In CAN communication, control units are connected
with 2 communication lines (CAN H-line, CAN L-line) allowing a high rate of information transmission with less
wiring. Each control unit transmits/receives data but selectively reads required data only.
CAN Communication Signal Chart. Refer to
LAN-28, "CAN COMMUNICATION SYSTEM : CAN Communica-
DTC Logic
INFOID:0000000008460442
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000008460443
1.
PERFORM SELF DIAGNOSTIC
1.
Turn ignition switch ON and wait for 2 seconds or more.
2.
Check “Self Diagnostic Result”.
Is DTC “U1000” displayed?
YES
>> Refer to
LAN-15, "Trouble Diagnosis Flow Chart"
NO
>> Refer to
GI-40, "Intermittent Incident"
.
DTC
CONSULT display de-
scription
DTC Detection Condition
Possible cause
U1000
CAN COMM
When BCM cannot communicate CAN com-
munication signal continuously for 2 seconds
or more.
CAN communication system
Revision: 2012 October
2013 Murano CrossCabriolet
BCS
U1010 CONTROL UNIT (CAN)
BCS-67
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
U1010 CONTROL UNIT (CAN)
DTC Logic
INFOID:0000000008460444
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000008460445
1.
REPLACE BCM
When DTC “U1010” is detected, replace BCM.
>> Replace BCM. Refer to
BCS-77, "Removal and Installation"
DTC
CONSULT display de-
scription
DTC Detection Condition
Possible cause
U1010
CONTROL UNIT(CAN)
BCM detected internal CAN communication circuit malfunction.
BCM
Revision: 2012 October
2013 Murano CrossCabriolet
BCS-68
< DTC/CIRCUIT DIAGNOSIS >
U0415 VEHICLE SPEED
U0415 VEHICLE SPEED
Description
INFOID:0000000008460446
U0415 is displayed if any unusual condition is present in the reception status of the vehicle speed signal from
the ABS actuator and electric unit (control unit).
DTC Logic
INFOID:0000000008460447
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
DTC CONFIRMATION
1.
Erase the DTC.
2.
Turn ignition switch OFF.
3.
Perform the “Self Diagnostic Result” of CONSULT, when passed 2 seconds or more after the ignition
switch is turned ON.
Is any DTC detected?
YES
>> Refer to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000008460448
1.
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAG RESULTS
Perform “Self-Diagnostic Result” of ABS actuator and electric unit (control unit) with CONSULT. Refer to
.
Is any DTC detected?
YES
>> Repair or replace the malfunctioning part.
NO
>> Replace BCM. Refer to
BCS-77, "Removal and Installation"
DTC
CONSULT display de-
scription
DTC Detection Condition
Probable cause
U0415
VEHICLE SPEED
When the vehicle speed signal received from
the ABS actuator and electric unit (control
unit) remains abnormal for 2 seconds or more.
• ABS actuator and electric unit (control unit)
• BCM
Revision: 2012 October
2013 Murano CrossCabriolet
BCS
B2562 LOW VOLTAGE
BCS-69
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
B2562 LOW VOLTAGE
DTC Logic
INFOID:0000000008460449
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
DTC CONFIRMATION
1.
Erase DTC.
2.
Turn ignition switch OFF.
3.
Perform the “Self Diagnostic Result” of CONSULT, when passed 120 seconds or more after the ignition
switch is turned ON.
Is any DTC detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000008460450
1.
CHECK POWER SUPPLY CIRCUIT
Check BCM power supply circuit. Refer to
Is the circuit normal?
YES
>> Replace BCM. Refer to
BCS-77, "Removal and Installation"
NO
>> Repair the malfunctioning part.
DTC
CONSULT display de-
scription
DTC Detection Condition
Possible cause
B2562
LOW VOLTAGE
When the power supply voltage to BCM remains less
than 8.8 V for 120 seconds or more
Harness or connector (power supply
circuit)
Revision: 2012 October
2013 Murano CrossCabriolet
BCS-70
< DTC/CIRCUIT DIAGNOSIS >
POWER SUPPLY AND GROUND CIRCUIT
POWER SUPPLY AND GROUND CIRCUIT
Diagnosis Procedure
INFOID:0000000008460451
1.
CHECK FUSE AND FUSIBLE LINK
Check that the following fuse and fusible link are not blown.
Is the fuse fusing?
YES
>> Replace the blown fuse or fusible link after repairing the affected circuit if a fuse or fusible link is
blown.
NO
>> GO TO 2.
2.
CHECK POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connectors.
3.
Check voltage between BCM harness connector and ground.
Is the measurement value normal?
YES
>> GO TO 3.
NO
>> Repair harness or connector.
3.
CHECK GROUND CIRCUIT
Check continuity between BCM harness connector and ground.
Does continuity exist?
YES
>> INSPECTION END
NO
>> Repair harness or connector.
Signal name
Fuse and fusible link No.
Battery power supply
L
10
Terminals
Voltage
(Approx.)
(+)
(
−
)
BCM
Ground
Connector
Terminal
M118
1
Battery voltage
M119
11
BCM
Ground
Continuity
Connector
Terminal
M119
13
Existed
Revision: 2012 October
2013 Murano CrossCabriolet
BCS
COMBINATION SWITCH INPUT CIRCUIT
BCS-71
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
COMBINATION SWITCH INPUT CIRCUIT
Diagnosis Procedure
INFOID:0000000008460452
1.
CHECK INPUT 1 - 5 SYSTEM CIRCUIT FOR OPEN
1.
Turn the ignition switch OFF.
2.
Disconnect the BCM and combination switch connectors.
3.
Check continuity between BCM harness connector and combination switch harness connector.
Does continuity exist?
YES
>> GO TO 2.
NO
>> Repair the harnesses or connectors.
2.
CHECK INPUT 1 - 5 SYSTEM CIRCUIT FOR SHORT
Check for continuity between BCM harness connector and ground.
Does continuity exist?
YES
>> Repair the harnesses or connectors.
NO
>> GO TO 3.
3.
CHECK BCM OUTPUT VOLTAGE
1.
Connect the BCM connector.
2.
Check voltage between BCM harness connector and ground.
Is the measurement value normal?
YES
>> GO TO 4.
NO
>> Replace BCM. Refer to
BCS-77, "Removal and Installation"
System
BCM
Combination switch
Continuity
Connector
Terminal
Connector
Terminal
INPUT 1
M122
107
M103
11
Existed
INPUT 2
109
9
INPUT 3
88
7
INPUT 4
108
10
INPUT 5
87
13
System
BCM
Ground
Continuity
Connector
Terminal
INPUT 1
M122
107
Not existed
INPUT 2
109
INPUT 3
88
INPUT 4
108
INPUT 5
87
System
Terminals
Voltage
(Approx.)
(+)
(
−
)
BCM
Ground
Connector
Terminal
INPUT 1
M122
107
Refer to
.
INPUT 2
109
INPUT 3
88
INPUT 4
108
INPUT 5
87
Revision: 2012 October
2013 Murano CrossCabriolet
BCS-72
< DTC/CIRCUIT DIAGNOSIS >
COMBINATION SWITCH INPUT CIRCUIT
4.
CHECK BCM INPUT SIGNAL
1.
Connect the combination switch connector.
2.
Turn ON any switch in the system that is malfunctioning.
3.
Check voltage between BCM harness connector and ground.
Is the measurement value normal when any of the switches is turned ON?
YES
>> Replace BCM. Refer to
BCS-77, "Removal and Installation"
NO
>> Replace the combination switch.
System
Terminals
Voltage
(Approx.)
(+)
(
−
)
BCM
Ground
Connector
Terminal
INPUT 1
M122
107
Refer to
INPUT 2
109
INPUT 3
88
INPUT 4
108
INPUT 5
87
Revision: 2012 October
2013 Murano CrossCabriolet
BCS
COMBINATION SWITCH OUTPUT CIRCUIT
BCS-73
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
COMBINATION SWITCH OUTPUT CIRCUIT
Diagnosis Procedure
INFOID:0000000008460453
1.
CHECK OUTPUT 1 - 5 SYSTEM CIRCUIT FOR OPEN
1.
Turn the ignition switch OFF.
2.
Disconnect the BCM and combination switch connectors.
NOTE:
BCM connector disconnects M123 only.
3.
Check continuity between BCM harness connector and combination switch harness connector.
Does continuity exist?
YES
>> GO TO 2.
NO
>> Repair the harnesses or connectors.
2.
CHECK OUTPUT 1 - 5 SYSTEM CIRCUIT FOR SHORT
Check for continuity between BCM harness connector and ground.
Does continuity exist?
YES
>> Repair the harnesses or connectors.
NO
>> GO TO 3.
3.
CHECK COMBINATION SWITCH INTERNAL CIRCUIT
1.
Connect the combination switch connector.
2.
Turn ON any switch in the system that is malfunctioning.
3.
Check voltage between combination switch harness connector and ground.
NOTE:
Check that the combination switch outputs a signal from combination switch input system.
System
BCM
Combination switch
Continuity
Connector
Terminal
Connector
Terminal
OUTPUT 1
M123
143
M103
12
Existed
OUTPUT 2
144
14
OUTPUT 3
145
5
OUTPUT 4
146
2
OUTPUT 5
142
8
System
BCM
Ground
Continuity
Connector
Terminal
OUTPUT 1
M123
143
Not existed
OUTPUT 2
144
OUTPUT 3
145
OUTPUT 4
146
OUTPUT 5
142
Revision: 2012 October
2013 Murano CrossCabriolet
BCS-74
< DTC/CIRCUIT DIAGNOSIS >
COMBINATION SWITCH OUTPUT CIRCUIT
Is the measurement value normal when any of the switches is turned ON?
YES
>> Replace BCM. Refer to
BCS-77, "Removal and Installation"
NO
>> Replace the combination switch.
System
Terminals
Value (Approx.)
(+)
(
−
)
Combination switch
Ground
Connector
Terminal
OUTPUT 1
M103
12
1.4 V
OUTPUT 2
14
OUTPUT 3
5
OUTPUT 4
2
OUTPUT 5
8
JPMIA0041GB
Revision: 2012 October
2013 Murano CrossCabriolet
BCS
COMBINATION SWITCH SYSTEM SYMPTOMS
BCS-75
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
SYMPTOM DIAGNOSIS
COMBINATION SWITCH SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000008460454
1.
Perform “Data Monitor” of CONSULT to check for any malfunctioning item.
2.
Check the malfunction combinations.
Malfunction item:
×
3.
Identify the malfunctioning part from the agreed combination and repair or replace the part.
Malfunction
combination
Data monitor item
FR WI
PER HI
FR WIP
ER LOW
F
R
W
A
SH
ER
S
W
FR WI
PER INT
INT VOL
U
ME
TURN SIG
NAL R
TURN SIGNAL L
T
A
IL
LA
MP
SW
H
I BEAM SW
HEAD LAMP SW
1
HEAD LAMP SW
2
P
ASSI
N
G
SW
AU
T
O
LI
GH
T
S
W
FR F
O
G
SW
A
×
×
×
×
B
×
×
×
×
C
×
×
×
D
×
×
×
E
×
×
F
×
×
G
×
×
H
×
×
×
I
×
×
×
×
J
×
×
×
×
K
All Items
L
If only one item is detected or the item is not applicable to the combinations A to K
Malfunction
combination
Malfunctioning part
Repair or replace
A
Combination switch INPUT 1 circuit
Inspect the combination switch input circuit applicable to the malfunctioning
part. Refer to
.
B
Combination switch INPUT 2 circuit
C
Combination switch INPUT 3 circuit
D
Combination switch INPUT 4 circuit
E
Combination switch INPUT 5 circuit
F
Combination switch OUTPUT 1 circuit
Inspect the combination switch output circuit applicable to the malfunction-
ing part. Refer to
.
G
Combination switch OUTPUT 2 circuit
H
Combination switch OUTPUT 3 circuit
I
Combination switch OUTPUT 4 circuit
J
Combination switch OUTPUT 5 circuit
K
BCM
BCS-77, "Removal and Installation"
L
Combination switch
Replace the combination switch.
Revision: 2012 October
2013 Murano CrossCabriolet
BCS-76
< SYMPTOM DIAGNOSIS >
NORMAL OPERATING CONDITION
NORMAL OPERATING CONDITION
Description
INFOID:0000000008973702
SHIPPING MODE
• Shipping mode inhibits battery power consumption during transportation or storage of the vehicle. Vehicle is
set to shipping mode before being shipped from the factory.
• When ignition switch is OFF, BCM operates shipping mode.
• BCM control function is limited in shipping mode. Remote keyless entry function is not operated during the
shipping mode.
• For shipping mode cancel operation, refer to
NOTE:
Do not cancel shipping mode during storage of the vehicle. Always cancel shipping mode before delivery of
the vehicle to customer.
Revision: 2012 October
2013 Murano CrossCabriolet
BCS
BCM (BODY CONTROL MODULE)
BCS-77
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
REMOVAL AND INSTALLATION
BCM (BODY CONTROL MODULE)
Removal and Installation
INFOID:0000000008460456
NOTE:
Before replacing BCM, perform “READ CONFIGURATION” to save or print current vehicle specification. Refer
to
.
REMOVAL
1.
Remove combination meter. Refer to
MWI-70, "Removal and Installation"
2.
Remove screws.
3.
Remove BCM and disconnect the connector.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Be sure to perform “WRITE CONFIGURATION” when replacing BCM. Or not doing so, BCM control
function does not operate normally.
NOTE:
Be sure to perform the system initialization (NATS) when replacing BCM. Refer to
.
Revision: 2012 October
2013 Murano CrossCabriolet
BCS-78
< REMOVAL AND INSTALLATION >
COMBINATION SWITCH
COMBINATION SWITCH
Exploded View
INFOID:0000000008460457
Removal and Installation
INFOID:0000000008460458
REMOVAL
1.
Remove steering column cover. Refer to
.
2.
Remove screws.
3.
Disconnect the connector.
4.
Pull up the combination switch to remove it.
INSTALLATION
Install in the reverse order of removal.
1.
Combination switch
2.
Combination switch connector
JPMIA0896ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст