Murano Cross Cabriolet Z51 (2013 year). Manual — part 80
B210F SHIFT POSITION/CLUTCH INTERLOCK SWITCH
SEC-89
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B210F SHIFT POSITION/CLUTCH INTERLOCK SWITCH
DTC Logic
INFOID:0000000008460570
DTC DETECTION LOGIC
NOTE:
If DTC B210F is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON and wait 1 second or more.
2.
Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000008460571
1.
CHECK DTC OF BCM
Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK P/N POSITION SIGNAL
1.
Turn ignition switch ON.
2.
Check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
.
NO
>> GO TO 3.
3.
CHECK P/N POSITION SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect TCM connector and IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and TCM harness connector.
4.
Check continuity between IPDM E/R harness connector and ground.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B210F
INTRLCK/PNP SW ON
IPDM E/R detects a mismatch between the sig-
nals below for 1 second or more.
• P/N position signal from TCM
• Shift position signal from BCM (CAN)
• Harness or connectors
(The CAN communication line is
open or shorted.)
• Harness or connectors
(TCM circuit is open or shorted.)
• TCM
(+)
(–)
Condition
Voltage (V)
(Approx.)
IPDM E/R
Connector
Terminal
E10
30
Ground
Selector lever
P or N
Battery voltage
Other than above
0
IPDM E/R
TCM
Continuity
Connector
Terminal
Connector
Terminal
F12
72
F23
20
Existed
Revision: 2012 October
2013 Murano CrossCabriolet
SEC-90
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B210F SHIFT POSITION/CLUTCH INTERLOCK SWITCH
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
NO
>> Repair or replace harness or connector.
IPDM E/R
Ground
Continuity
Connector
Terminal
F12
72
Not existed
Revision: 2012 October
2013 Murano CrossCabriolet
B2110 SHIFT POSITION/CLUTCH INTERLOCK SWITCH
SEC-91
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B2110 SHIFT POSITION/CLUTCH INTERLOCK SWITCH
DTC Logic
INFOID:0000000008460572
DTC DETECTION LOGIC
NOTE:
If DTC B2110 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn the ignition switch ON and wait 1 second or more.
2.
Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000008460573
1.
CHECK DTC OF TCM
Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK P/N POSITION SIGNAL
1.
Turn ignition switch ON.
2.
Check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
.
NO
>> GO TO 3.
3.
CHECK P/N POSITION SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect TCM connector and IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and TCM harness connector.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B2110
INTRLCK/PNP SW OFF
IPDM E/R detects mismatch between the following
signals for 1 second or more.
• P/N position signal from TCM
• Shift position signal from BCM (CAN)
• Harness or connectors
(The CAN communication line is open
or shorted.)
• Harness or connectors
(TCM circuit is open or shorted.)
• TCM
• IPDM E/R
• BCM
(+)
(–)
Condition
Voltage (V)
(Approx.)
IPDM E/R
Connector
Terminal
E10
30
Ground
Selector lever
P or N
Battery voltage
Other than above
0
Revision: 2012 October
2013 Murano CrossCabriolet
SEC-92
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2110 SHIFT POSITION/CLUTCH INTERLOCK SWITCH
4.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
NO
>> Repair or replace harness or connector.
IPDM E/R
TCM
Continuity
Connector
Terminal
Connector
Terminal
F12
72
F23
20
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
F12
72
Not existed
Revision: 2012 October
2013 Murano CrossCabriolet
HEADLAMP FUNCTION
SEC-93
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
HEADLAMP FUNCTION
Component Function Check
INFOID:0000000008460574
1.
CHECK FUNCTION
1.
Perform “HEAD LAMP(HI)” in “ACTIVE TEST” mode of “THEFT ALM” of “BCM” using CONSULT.
2.
Check headlamps operation.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
Diagnosis Procedure
INFOID:0000000008460575
1.
CHECK HEADLAMP FUNCTION
EXL-37, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK INTERMITTENT INCIDENT
GI-40, "Intermittent Incident"
.
>> INSPECTION END
Test item
Description
HEAD LAMP (HI)
ON
Headlamps (Hi)
Light
OFF
Do not light
Revision: 2012 October
2013 Murano CrossCabriolet
SEC-94
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
HORN FUNCTION
HORN FUNCTION
Component Function Check
INFOID:0000000008460576
1.
CHECK FUNCTION
1.
Perform “VEHICLE SECURITY HORN” in “ACTIVE TEST” mode of “THEFT ALM” of “BCM” using CON-
SULT.
2.
Check the horn operation.
Is the operation normal?
YES
>> INSPECTION END
NO
>> Go to
.
Diagnosis Procedure
INFOID:0000000008460577
1.
CHECK HORN FUNCTION
Check that horns function properly using horn switch.
Does horn sound?
YES
>> GO TO 2.
NO
>> Check horn circuit. Refer to
2.
CHECK HORN CONTROL CIRCUIT
1.
Disconnect horn relay.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and horn relay harness connector.
4.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
NO
>> Repair or replace harness.
Test item
Description
VEHICLE SECURITY HORN
ON
Horn
Sounds (for 0.5 sec)
IPDM E/R
Horn relay
Continuity
Connector
Terminal
Connector
Terminal
E11
44
E5
1
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
E11
44
Not existed
Revision: 2012 October
2013 Murano CrossCabriolet
KEY WARNING LAMP
SEC-95
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
KEY WARNING LAMP
Component Function Check
INFOID:0000000008460578
1.
CHECK FUNCTION
Check the operation with “INDICATOR” in “Active Test” mode with CONSULT.
Is the inspection result normal?
YES
>> Key warning lamp in combination meter is OK.
NO
>> Refer to
Diagnosis Procedure
INFOID:0000000008460579
1.
CHECK KEY WARNING LAMP
SEC-95, "Component Function Check"
Is the inspection result normal?
Yes
>> GO TO 2.
No
>> Repair or replace key warning lamp circuit.
2.
CHECK INTERMITTENT INCIDENT
GI-40, "Intermittent Incident"
.
>> INSPECTION END
Test item
Condition
INDICATOR
KEY ON
Key warning lamp illuminates
KEY IND
Key warning lamp flashes
Revision: 2012 October
2013 Murano CrossCabriolet
SEC-96
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
SECURITY INDICATOR LAMP
SECURITY INDICATOR LAMP
Component Function Check
INFOID:0000000008460580
1.
CHECK FUNCTION
1.
Perform “THEFT IND” in the “ACTIVE TEST” mode with CONSULT.
2.
Check security indicator lamp operation.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Go to
Diagnosis Procedure
INFOID:0000000008460581
1.
CHECK SECURITY INDICATOR LAMP POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect security indicator lamp connector.
3.
Check voltage between security indicator lamp harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO-1
>> Check 10 A fuse [No. 6, located in the fuse block (J/B)].
NO-2
>> Check harness for open or short between security indicator lamp and fuse.
2.
CHECK SECURITY INDICATOR LAMP SIGNAL
1.
Connect security indicator lamp connector.
2.
Disconnect BCM connector.
3.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-77, "Removal and Installation"
NO
>> GO TO 3.
3.
CHECK SECURITY INDICATOR LAMP SIGNAL CIRCUIT
1.
Disconnect security indicator lamp connector.
2.
Check continuity between security indicator lamp harness connector and BCM harness connector.
3.
Check continuity between security indicator lamp harness connector and ground.
Test item
Description
THEFT IND
ON
Security indicator lamp
Illuminate
OFF
Not illuminate
(+)
(–)
Voltage (V)
(Approx.)
Security indicator lamp
Connector
Terminal
M100
1
Ground
Battery voltage
(+)
(–)
Voltage (V)
(Approx.)
BCM
Connector
Terminal
M123
141
Ground
Battery voltage
Security indicator lamp
BCM
Continuity
Connector
Terminal
Connector
Terminal
M100
2
M123
141
Existed
Revision: 2012 October
2013 Murano CrossCabriolet
SECURITY INDICATOR LAMP
SEC-97
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
Is the inspection result normal?
YES
>> Replace security indicator lamp. Refer to
SEC-111, "Removal and Installation"
.
NO
>> Repair or replace harness.
Security indicator lamp
Ground
Continuity
Connector
Terminal
M100
2
Not existed
Revision: 2012 October
2013 Murano CrossCabriolet
SEC-98
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
TRUNK KEY CYLINDER SWITCH
TRUNK KEY CYLINDER SWITCH
Component Function Check
INFOID:0000000008460582
1.
CHECK FUNCTION
1.
Select “KEY CYL SW-TR” in “Data Monitor” mode of “THEFT ALM” of “BCM” using CONSULT.
2.
Check the indication under the following conditions.
Is the inspection result normal?
YES
>> Trunk key cylinder switch is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000008460583
1.
CHECK TRUNK KEY CYLINDER SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect trunk key cylinder switch connector.
3.
Check voltage between trunk key cylinder switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 2.
2.
CHECK TRUNK KEY CYLINDER SWITCH SIGNAL CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and trunk key cylinder switch harness connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-77, "Removal and Installation"
.
2.
Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.
>> INSPECTION END
Monitor item
Condition
Indication
KEY CYL SW-TR
Trunk key cylinder switch
Off position
Off
On (Trunk lid open) position
On
(+)
(–)
Voltage
(Approx.)
Trunk key cylinder switch
Connector
Terminal
T11
1
Ground
12 V
BCM
Trunk key cylinder switch
Continuity
Connector
Terminal
Connector
Terminal
M121
49
T11
1
Existed
BCM
Ground
Continuity
Connector
Terminal
M121
49
Not existed
Revision: 2012 October
2013 Murano CrossCabriolet
TRUNK KEY CYLINDER SWITCH
SEC-99
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
4.
CHECK TRUNK KEY CYLINDER SWITCH GROUND CIRCUIT
Check continuity between trunk key cylinder switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
CHECK TRUNK KEY CYLINDER SWITCH
SEC-99, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace trunk key cylinder switch.
6.
CHECK INTERMITTENT INCIDENT
GI-40, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000008460584
1.
CHECK TRUNK KEY CYLINDER SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect trunk key cylinder switch connector.
3.
Check continuity between trunk key cylinder switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace trunk key cylinder switch.
Trunk key cylinder switch
Ground
Continuity
Connector
Terminal
T11
2
Existed
Trunk key cylinder switch
Condition
Continuity
Terminal
1
2
Trunk lid key cylinder
Off position
Not existed
On (trunk lid open) position
Existed
Revision: 2012 October
2013 Murano CrossCabriolet
SEC-100
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
ENGINE DOES NOT START WHEN INTELLIGENT KEY IS INSIDE OF VEHICLE
SYMPTOM DIAGNOSIS
ENGINE DOES NOT START WHEN INTELLIGENT KEY IS INSIDE OF VE-
HICLE
Description
INFOID:0000000008460585
Engine does not start when push-button ignition switch is pressed while carrying Intelligent Key.
NOTE:
• Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and
check each symptom.
• The engine start function, door lock function, power distribution system, and NATS-IVIS/NVIS in the Intelli-
gent Key system are closely related to each other regarding control. The vehicle security function can oper-
ate only when the door lock and power distribution system are operating normally.
Conditions of Vehicle (Operating Conditions)
• “ENGINE START BY I-KEY” setting: ON
Check the setting of “ENGINE START BY I-KEY” in “Work Support” mode of “INTELLIGENT KEY” of “BCM”
using CONSULT.
• Intelligent Key is not inserted into key slot.
• One or more of Intelligent Keys with registered Intelligent Key ID is in the vehicle.
Diagnosis Procedure
INFOID:0000000008460586
1.
PERFORM WORK SUPPORT
Perform “INSIDE ANT DIAGNOSIS” in “Work Support” mode of “INTELLIGENT KEY” of “BCM” using CON-
SULT.
Refer to
SEC-21, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSTIC RESULT
Select “Self Diagnostic Result” mode of “BCM”, and check whether or not DTC of inside key antenna is
detected.
Is DTC detected?
YES
>> Refer to
(trunk room).
NO
>> GO TO 3.
3.
CHECK PUSH-BUTTON IGNITION SWITCH
Check push-button ignition switch.
Refer to
PCS-65, "Component Function Check"
Is the operation normal?
YES
>> GO TO 4.
NO
>> Repair or replace malfunctioning parts.
4.
CONFIRM THE OPERATION
Confirm the operation again.
Is the inspection normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2012 October
2013 Murano CrossCabriolet
SECURITY INDICATOR LAMP DOES NOT TURN ON OR BLINK
SEC-101
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
SECURITY INDICATOR LAMP DOES NOT TURN ON OR BLINK
Description
INFOID:0000000008460587
Security indicator lamp does not blink when ignition switch is in a position other than ON.
NOTE:
• Before performing the diagnosis in the following table, check “Work Flow”. Refer to
• Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and
check each symptom.
Conditions of Vehicle (Operating Conditions)
• Intelligent Key is not inserted in key slot.
• Ignition switch position is not in the ON position.
Diagnosis Procedure
INFOID:0000000008460588
1.
CHECK SECURITY INDICATOR LAMP
Check security indicator lamp.
Refer to
SEC-96, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2012 October
2013 Murano CrossCabriolet
SEC-102
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
VEHICLE SECURITY SYSTEM CANNOT BE SET
VEHICLE SECURITY SYSTEM CANNOT BE SET
INTELLIGENT KEY
INTELLIGENT KEY : Description
INFOID:0000000008460589
ARMED phase is not activated when all doors are locked using Intelligent Key.
NOTE:
Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and check
each symptom.
CONDITION OF VEHICLE (OPERATING CONDITION)
• “ENGINE START BY I-KEY” setting: ON
Check the setting of “ENGINE START BY I-KEY” in “Work Support” mode of “INTELLIGENT KEY” of “BCM”
using CONSULT.
INTELLIGENT KEY : Diagnosis Procedure
INFOID:0000000008460590
1.
CHECK INTELLIGENT KEY SYSTEM (REMOTE KEYLESS ENTRY FUNCTION)
Lock/unlock door with Intelligent Key.
Refer to
DLK-20, "REMOTE KEYLESS ENTRY FUNCTION : System Description"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check Intelligent Key system (remote keyless entry function). Refer to
2.
CHECK DOOR SWITCH
Check door switch circuit.
Refer to
DLK-55, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace malfunctioning parts. Refer to
3.
CHECK TRUNK ROOM LAMP SWITCH
Check trunk room lamp switch circuit.
Refer to
DLK-69, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace malfunctioning parts. Refer to
4.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
DOOR REQUEST SWITCH
DOOR REQUEST SWITCH : Description
INFOID:0000000008460591
ARMED phase is not activated when all doors are locked using door request switch.
NOTE:
Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and check
each symptom.
CONDITION OF VEHICLE (OPERATING CONDITION)
• “ENGINE START BY I-KEY” setting: ON
Check the setting of “ENGINE START BY I-KEY” in “Work Support” mode of “INTELLIGENT KEY” of “BCM”
using CONSULT.
Revision: 2012 October
2013 Murano CrossCabriolet
VEHICLE SECURITY SYSTEM CANNOT BE SET
SEC-103
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
DOOR REQUEST SWITCH : Diagnosis Procedure
INFOID:0000000008460592
1.
CHECK INTELLIGENT KEY SYSTEM (DOOR LOCK FUNCTION)
Lock/unlock door with door request switch.
Refer to
DLK-16, "DOOR LOCK FUNCTION : System Description"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check Intelligent Key system (door lock function). Refer to
DLK-102, "ALL DOOR : Diagnosis Pro-
2.
CHECK DOOR SWITCH
Check door switch circuit.
Refer to
DLK-55, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace malfunctioning parts.
3.
CHECK TRUNK ROOM LAMP SWITCH
Check trunk room lamp switch circuit.
Refer to
DLK-69, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace malfunctioning parts.
4.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
DOOR KEY CYLINDER
DOOR KEY CYLINDER : Description
INFOID:0000000008460593
ARMED phase is not activated when all doors are locked using mechanical key.
DOOR KEY CYLINDER : Diagnosis Procedure
INFOID:0000000008460594
1.
CHECK POWER DOOR LOCK SYSTEM
Lock/unlock door with mechanical key.
Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check power door lock system. Refer to
DLK-101, "Diagnosis Procedure"
.
2.
CHECK DOOR SWITCH
Check door switch circuit.
Refer to
DLK-55, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace malfunctioning parts.
3.
CHECK TRUNK ROOM LAMP SWITCH
Check trunk room lamp switch circuit.
Refer to
DLK-69, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 4.
Revision: 2012 October
2013 Murano CrossCabriolet
SEC-104
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
VEHICLE SECURITY SYSTEM CANNOT BE SET
NO
>> Repair or replace malfunctioning parts.
4.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
DOOR LOCK AND UNLOCK SWITCH
DOOR LOCK AND UNLOCK SWITCH : Description
INFOID:0000000008460595
Armed phase is not activated when all doors are locked by door lock and unlock switch.
NOTE:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-
TIONS)” before starting diagnosis, and check each symptom.
CONDITION OF VEHICLE (OPERATING CONDITIONS)
“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using
CONSULT.
DOOR LOCK AND UNLOCK SWITCH : Diagnosis Procedure
INFOID:0000000008460596
1.
CHECK DTC OF SOFT TOP CONTROL UNIT
Check DTC in “Self Diagnostic Result” mode of “CONVERTIBLE ROOF” using CONSULT.
Is DTC detected?
YES
>> Perform the trouble diagnosis regarding to the detected DTC. Refer to
NO
>> GO TO 2.
2.
CHECK DOOR LOCK FUNCTION
Lock/unlock door using door lock and unlock switches (Driver side and passenger side).
Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Check power door lock system. Refer to
DLK-99, "ALL DOOR : Diagnosis Procedure"
.
3.
CHECK DOOR SWITCH
Check door switch circuit.
Refer to
DLK-55, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace malfunctioning parts.
4.
CHECK TRUNK ROOM LAMP SWITCH
Check trunk room lamp switch circuit.
Refer to
DLK-69, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace malfunctioning parts.
5.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2012 October
2013 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст