Nissan Juke (2012 year). Service Repair Manual — part 55
INSIDE KEY ANTENNA
DLK-163
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
LUGGAGE ROOM : Exploded View
INFOID:0000000007578955
LUGGAGE ROOM : Removal and Installation
INFOID:0000000007578956
REMOVAL
1.
Remove the luggage floor finisher. Refer to
.
2.
Remove the inside key antenna (luggage room) (1) mounting
clip RH (A).
3.
Disengage inside key antenna (luggage room) fixing clip using a
flat-bladed screwdriver (A), and then pull out forward the inside
key antenna (luggage room).
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Visually check the clips for deformation and damage during installation.
Replace with new ones if necessary.
1.
Inside key antenna (luggage room)
2.
Clip
: Do not reuse
JMKIA5576ZZ
JMKIA5577ZZ
JMKIA5578ZZ
Revision: 2011 October
2012 JUKE
DLK-164
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
OUTSIDE KEY ANTENNA
OUTSIDE KEY ANTENNA
DRIVER SIDE
DRIVER SIDE : Removal and Installation
INFOID:0000000007578957
REMOVAL
Remove the driver side outside handle. Refer to
DLK-150, "OUTSIDE HANDLE : Removal and Installation"
.
INSTALLATION
Install in the reverse order of removal.
PASSENGER SIDE
PASSENGER SIDE : Removal and Installation
INFOID:0000000007578958
REMOVAL
Remove the passenger side outside handle. Refer to
DLK-150, "OUTSIDE HANDLE : Removal and Installa-
.
INSTALLATION
Install in the reverse order of removal.
REAR BUMPER
REAR BUMPER : Removal and Installation
INFOID:0000000007578959
REMOVAL
1.
Remove the rear bumper fascia. Refer to
EXT-15, "Removal and Installation"
2.
Remove the outside key antenna (rear bumper) (1) mounting
clip (A), then remove outside key antenna (rear bumper).
INSTALLATION
Install in the reverse order of removal.
JMKIA5580ZZ
Revision: 2011 October
2012 JUKE
INTELLIGENT KEY WARNING BUZZER
DLK-165
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INTELLIGENT KEY WARNING BUZZER
Removal and Installation
INFOID:0000000007578960
REMOVAL
1.
Remove the Intelligent Key warning buzzer (1) mounting bolt
(A), and then remove the Intelligent Key warning buzzer.
INSTALLATION
Install in the reverse order of removal.
JMKIA5571ZZ
Revision: 2011 October
2012 JUKE
DLK-166
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
REMOTE KEYLESS ENTRY RECEIVER
REMOTE KEYLESS ENTRY RECEIVER
Removal and Installation
INFOID:0000000007578961
REMOVAL
1.
Remove the glove box assembly. Refer to
IP-12, "Removal and Installation"
2.
Remove the remote keyless entry receiver (1) mounting bolt (A),
and then remove remote keyless entry receiver.
INSTALLATION
Install in the reverse order of removal.
JMKIA6084ZZ
Revision: 2011 October
2012 JUKE
INTELLIGENT KEY BATTERY
DLK-167
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INTELLIGENT KEY BATTERY
Removal and Installation
INFOID:0000000007578962
1.
Release the lock knob at the back of the Intelligent Key and remove the mechanical key.
2.
Insert a remover tool (A) wrapped with a cloth into the slit of the
corner and twist it to separate the upper part from the lower part.
CAUTION:
• Do not touch the circuit board or battery terminal.
• The key fob is water-resistant. However, if it does get wet,
immediately wipe it dry.
3.
Replace the battery with new one.
4.
Align the tips of the upper and lower parts, and then push them
together until it is securely closed.
CAUTION:
• When replacing battery, keep dirt, grease, and other for-
eign materials off the electrode contact area.
• After replacing the battery, check that all Intelligent Key
functions work normally.
PIIB6221E
Battery replacement
:Coin-type lithium battery
(CR2025)
PIIB6222E
Revision: 2011 October
2012 JUKE
DLK-168
< PRECAUTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000007578963
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution for Procedure without Cowl Top Cover
INFOID:0000000007578965
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.
Work
INFOID:0000000007578966
• After removing and installing the opening/closing parts, be sure to carry out fitting adjustments to check their
operational.
• Check the lubrication level, damage, and wear of each part. If necessary, grease or replace it.
PIIB3706J
Revision: 2011 October
2012 JUKE
PREPARATION
DLK-169
< PREPARATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000007578967
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
INFOID:0000000007578968
Tool number
(Kent-Moore No.)
Tool name
Description
(J-39570)
Chassis ear
Locating the noise
(J-43980)
NISSAN Squeak and Rat-
tle Kit
Repairing the cause of noise
SIIA0993E
SIIA0994E
Tool name
Description
Engine ear
Locating the noise
Remover tool
Remove the clips, pawls, and metal clips
Power tool
SIIA0995E
PIIB7923J
PIIB1407E
Revision: 2011 October
2012 JUKE
DLK-170
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location
INFOID:0000000007578969
Component Description
INFOID:0000000007578970
1.
IPDM E/R
Refer to
2.
TCM
Refer to
SYSTEM : Component Parts Loca-
tion"
3.
Combination meter
4.
Key switch
5.
BCM
Refer to
SYSTEM : Component Parts Loca-
tion"
6.
Power window main switch
(door lock/unlock switch)
7.
Front door switch (driver side)
8.
Front door lock assembly (driver
side)
9.
Back door opener assembly
10. Back door opener switch
11.
Remote keyless entry receiver
A.
View with the glove box assembly re-
moved
JMKIA6160ZZ
Item
Function
Back door opener actuator
Opens the back door with the back door open signal from BCM.
Back door opener switch
Inputs back door opener switch operation signal to BCM.
BCM
Controls the door lock system.
Revision: 2011 October
2012 JUKE
COMPONENT PARTS
DLK-171
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Combination meter
• Performs operation method guide and warning with buzzer.
• Transmits vehicle seep signal to CAN communication line.
Door lock actuator
• Inputs locks/unlocks signal from BCM and locks/unlocks each door.
• Integrated in each door lock assembly.
Door lock and unlock switch
Transmits door lock/unlock operation to BCM.
Door switch
Detects door open/close condition.
IPDM E/R
Sounds horn via CAN communication between BCM.
Keyfob
Transmits button operation to remote keyless entry receiver.
Key switch
Key switch detects that ignition key is inserted into the ignition key cylinder, and
then transmits the signal to BCM.
Remote keyless entry receiver
Receives keyfob operation and transmits to BCM.
TCM
Transmits shift position signal to BCM via CAN communication line.
Item
Function
Revision: 2011 October
2012 JUKE
DLK-172
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
POWER DOOR LOCK SYSTEM
POWER DOOR LOCK SYSTEM
System Diagram
INFOID:0000000007578971
System Description
INFOID:0000000007578972
DOOR LOCK FUNCTION
• The door lock and unlock switch (driver side) is build into power window main switch.
• Interlocked with the locking operation of door lock and unlock switch, door lock actuators of all doors are
locked.
• Interlocked with the unlocking operation of door lock and unlock switch, door lock actuators of all doors and
are unlocked.
Door Key Cylinder
• With the door key inserted in the door key cylinder on driver side, turning it to “LOCK”, will lock door lock
actuator of all doors.
• With the door key inserted in the door key cylinder on driver side, turning it to “UNLOCK” once unlocks the
driver side door lock actuator; turning it to “UNLOCK” again within 5 seconds after the first unlock operation
unlocks all of the other doors. (SELECTIVE UNLOCK OPERATION)
KEY REMINDER FUNCTION
When door lock and unlock switch are operated while key is inserted into key switch and any door is open,
door locks once but immediately unlocks. This operation prevents keyfob from being left in the vehicle.
AUTOMATIC DOOR LOCK/UNLOCK FUNCTION (LOCK OPERATION)
The interlock door lock function is the function that locks all doors linked with the vehicle speed or shift posi-
tion. It has 2 types as follows.
Vehicle Speed Sensing Auto Door Lock
All doors are locked when the vehicle speed reaches 24 km/h (15 MPH) or more.
BCM outputs the lock signal to all door lock actuators when it detects that the ignition switch is turned ON, all
doors are closed and the vehicle speed received from the combination meter via CAN communication
becomes 24 km/h (15 MPH) or more.
P Range Interlock Door Lock*
All doors are locked when shifting the selector lever from the P position to any position other than P.
BCM outputs the lock signal to all door lock actuators when it detects that the ignition switch is in the ON posi-
tion and the shift signal received from the TCM via CAN communication is shifted from the P position to any
position other than P.
Setting change of Automatic Door Lock/Unlock Function
The lock operation setting of the automatic door lock/unlock function can be changed.
With CONSULT
The ON/OFF switching of the automatic door lock function and the type selection of the automatic door lock/
unlock function can be performed at the WORK SUPPORT setting of CONSULT.
Without CONSULT
JMKIA6161GB
Revision: 2011 October
2012 JUKE
POWER DOOR LOCK SYSTEM
DLK-173
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
The automatic door lock function ON/OFF can be switched by performing the following operation.
1.
Close all doors (door switch OFF)
2.
Turn ignition switch ON
3.
Press and hold the door lock and unlock switch for 5 seconds or more in the lock direction within 20 sec-
onds after turning the ignition switch ON.
4.
The switching is completed when the hazard warning lamp blinks.
AUTOMATIC DOOR LOCK/UNLOCK FUNCTION (UNLOCK OPERATION)
The automatic door lock/unlock function is the function that unlocks all doors linked with the key position or
shift position. It has 3 types as follows.
IGN OFF Interlock Door Unlock
All doors are unlocked when the power supply position is changed from ON to OFF.
BCM outputs the unlock signal to all door lock actuators when it detects that the power supply position is
changed from ignition switch ON to OFF.
Key out Interlock Door Unlock
When ignition key is removed from ignition knob switch, all doors unlock.
When BCM detects that ignition key is removed from ignition knob switch, BCM transmits unlock signal to all
door lock actuators.
P Range Interlock Door Unlock*
All doors are unlocked when shifting the selector lever from any position other than the P to P position.
BCM outputs the unlock signal to all door lock actuators when it detects that the ignition switch is in the ON
position and the shift signal received from TCM via CAN communication is shifted from any position other than
the P to P position.
Setting change of Automatic Door Lock/Unlock Function
The unlock operation setting of the automatic door lock/unlock function can be changed.
With CONSULT
The ON/OFF switching of the automatic door lock/unlock function and the type selection of the automatic door
lock/unlock function can be performed at the WORK SUPPORT setting of CONSULT.
Without CONSULT
The automatic door lock/unlock function ON/OFF can be switched by performing the following operation.
1.
Close all doors below (door switch OFF)
2.
Turn ignition switch ON
3.
Press and hold the door lock and unlock switch for 5 seconds or more in the unlock direction within 20
seconds after turning the power supply position ON.
4.
The switching is completed when the hazard warning lamp blinks.
*: This function does not operate on M/T models.
OFF
→
ON
: 2 blinks
ON
→
OFF
: 1 blink
OFF
→
ON
: 2 blinks
ON
→
OFF
: 1 blink
Revision: 2011 October
2012 JUKE
DLK-174
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
REMOTE KEYLESS ENTRY SYSTEM
REMOTE KEYLESS ENTRY SYSTEM
System Diagram
INFOID:0000000007578973
System Description
INFOID:0000000007578974
DOOR LOCK AND UNLOCK OPERATION
• When door lock and unlock button of keyfob is pressed, door lock and unlock signal transmits from keyfob to
BCM via remote keyless entry receiver.
• When BCM receives the door lock and unlock signal, it operates door lock actuator, blinks the hazard lamp
at the same time as a reminder.
OPERATION CONDITION
If the following conditions are satisfied, door lock/unlock operation is performed if the keyfob is operated.
OPERATION AREA
To ensure that the keyfob works effectively, use within 1 m (3 ft) range of each door, however the operable
range may differ according to surroundings.
SELECTIVE UNLOCK FUNCTION
• When an LOCK signal is transmitted from keyfob, all doors are locked.
• When an UNLOCK signal is transmitted from keyfob once, driver side door is unlocked.
• Then, if an UNLOCK signal is transmitted from keyfob again, all other doors are unlocked.
How to change selective unlock mode.
With CONSULT
Selective unlock mode can be set to ON or OFF using CONSULT.
Refer to
DLK-177, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
Without CONSULT
• ON/OFF can be switched when keyfob lock button and unlock button are pressed simultaneously for 5 sec-
onds or more while steering lock is locked.
• When mode is switched, hazard warning lamp blinks.
HAZARD AND HORN REMINDER FUNCTION
When doors are locked or unlocked by keyfob, BCM blinks hazard warning lamps as a reminder and transmits
horn chirp signal to IPDM E/R. IPDM E/R sounds horn as a reminder.
The hazard and horn reminder has a horn chirp mode (C mode) and a non-horn chirp mode (S mode).
Operating Function of Hazard and Horn Reminder
JMKIA6162GB
Remote controller operation
Operation condition
Lock/unlock
Ignition key is removed from ignition key cylinder
OFF
→
ON
: 3 blinks
ON
→
OFF
: 1 blink
Revision: 2011 October
2012 JUKE
REMOTE KEYLESS ENTRY SYSTEM
DLK-175
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Hazard and horn reminder does not operate if ignition switch ON position.
How to change hazard and horn reminder mode
With CONSULT
DLK-177, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
Without CONSULT
When LOCK and UNLOCK signals are sent from the Intelligent Key for more than 2 seconds at the same time,
the hazard and horn reminder mode is changed and hazard warning lamp blinks and horn sounds as per the
following items:
AUTO DOOR LOCK FUNCTION
After door is unlocked by keyfob button operation and if 1 minute or more passes without performing the fol-
lowing operation, all doors are automatically locked. However, operation check function does not activate.
Auto door lock mode can be changed by the “AUTO LOCK SET” mode in “WORK SUPPORT”. Refer to
177, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
PANIC ALARM FUNCTION
When key switch in the OFF position, BCM transmits horn reminder signal to IPDM E/R. Then, IPDM E/R
turns on and off horn intermittently. Refer to
SEC-123, "VEHICLE SECURITY SYSTEM : System Description"
.
INTERIOR ROOM LAMP CONTROL FUNCTION
Interior room lamp is controlled according to door lock/unlock state, refer to
CONTROL SYSTEM : System Description"
C mode
S mode
Keyfob operation
Lock
Unlock
Back door
open
Lock
Unlock
Back door
open
Hazard warning lamp blinks
Twice
Once
—
Twice
—
—
Horn sound
Once
—
—
—
—
—
JMKIA6362GB
Operating condition
• Door switch is ON (door is open)
• Door is locked
• Key switch is ON
Revision: 2011 October
2012 JUKE
DLK-176
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
BACK DOOR OPENER SYSTEM
BACK DOOR OPENER SYSTEM
System Diagram
INFOID:0000000007578975
System Description
INFOID:0000000007578976
BACK DOOR OPENER OPERATION
When back door opener switch is pressed, BCM operates back door opener actuator.
NOTE:
Back door opener actuator is not for locking the back door. The function is only to open the back door.
OPERATION CONDITION
If the following conditions are satisfied, back door opener operation is performed.
NOTE:
• When battery terminal is disconnected and reconnected during all doors unlock state, back door may not
open.
• Regardless of door lock actuator state, BCM resets recognition of all doors unlock state approximately 30
seconds after battery terminal is disconnected and BCM recognizes that all doors are in lock state.
• When battery terminal is reconnected and back door does not open, have BCM recognize that all doors are
in unlock state.
JMKIA6011GB
Back door opener switch operation
Operation condition
Back door open
• When back door is unlocked using back door opener request switch (selective unlock
mode), or after BCM outputs all doors unlock signal
• Vehicle speed is less than 5 km/h (3 MPH)
Revision: 2011 October
2012 JUKE
DIAGNOSIS SYSTEM (BCM)
DLK-177
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000007818190
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
DOOR LOCK
DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)
INFOID:0000000007578978
WORK SUPPORT
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp control
INT LAMP
×
×
×
Remote keyless entry system
MULTI REMOTE ENT
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
Air conditioning system
AIR CONDITONER
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
NATS
IMMU
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Back door open
TRUNK
×
Theft warning alarm
THEFT ALM
×
×
×
RAP system
RETAINED PWR
×
×
Signal buffer system
SIGNAL BUFFER
×
×
Panic alarm
PANIC ALARM
×
TPMS
AIR PRESSUE MONITOR
×
×
×
Revision: 2011 October
2012 JUKE
DLK-178
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
*: P range interlock door lock/unlock can be selected for M/T models, but automatic door lock/unlock function does not operate.
DATA MONITOR
ACTIVE TEST
Monitor item
Description
DOOR LOCK-UNLOCK SET
Anti-hijack function can be changed to operate with this mode
• On: Operate
• Off: Non-operation
AUTOMATIC DOOR LOCK SE-
LECT
Automatic door lock function can be selected from the following in this mode
• VH SPD: All doors are locked when vehicle speed more than 24km/h (15MPH)
• P RANGE*: All doors are locked when shifting the selector lever from P position to other
than the P position
AUTOMATIC DOOR UNLOCK
SELECT
Automatic door unlock function can be selected from the following in the mode
• MODE 1: All doors are unlocked when the power supply position is changed from ON to
OFF
• MODE 2*: All doors are unlocked when shifting the selector lever from any position other
than the P to P position
• MODE 3: Driver side door is unlocked when the power supply position is changed from ON
to OFF
• MODE 4*: Driver side door is unlocked when shifting the selector lever from any position
other than the P to P position
• MODE 5: Driver side door is unlocked when key out of key switch
• MODE 6: All doors are unlocked when key out of key switch
AUTOMATIC LOCK/UNLOCK
SET
Automatic door lock/unlock function can be selected from the following in this mode
• Off: Non-operation
• Unlock Only: Door unlock operation only
• Lock Only: Door lock operation only
• Lock/Unlock: Door lock and unlock operation
Monitor Item
Contents
IGN ON SW
Indicated [On/Off] condition of ignition switch in ON position
KEY ON SW
Indicated [On/Off] condition of key switch
CDL LOCK SW
Indicated [On/Off] condition of lock signal from door lock unlock switch
CDL UNLOCK SW
Indicated [On/Off] condition of unlock signal from door lock unlock switch
DOOR SW-DR
Indicated [On/Off] condition of front door switch (driver side)
DOOR SW-AS
Indicated [On/Off] condition of front door switch (passenger side)
DOOR SW-RR
Indicated [On/Off] condition of rear door switch RH
DOOR SW-RL
Indicated [On/Off] condition of rear door switch LH
BACK DOOR SW
Indicated [On/Off] condition of back door switch
LOCK STATUS
Indicated [On/Off] condition of front door driver side
ACC ON SW
Indicated [On/Off] condition of ignition switch in ACC position
KEYLESS LOCK
Indicated [On/Off] condition of lock signal from key fob
KEYLESS UNLOCK
Indicated [On/Off] condition of unlock signal from key fob
KEY CYL LK-SW
Indicated [On/Off] condition of lock signal from door key cylinder
KEY CYL UN-SW
Indicated [On/Off] condition of unlock signal from door key cylinder
VEHICLE SPEED
Display the vehicle speed signal received from combination meter by numer-
ical value [Km/h]
Revision: 2011 October
2012 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст