Nissan Juke (2012 year). Service Repair Manual — part 88
P0130 A/F SENSOR 1
EC-225
< DTC/CIRCUIT DIAGNOSIS >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
If “TESTING” is not displayed after 20 seconds, retry from step 2.
CAUTION:
Always drive vehicle at a safe speed.
Is “TESTING” displayed on CONSULT screen?
YES
>> GO TO 5.
NO
>> Check A/F sensor 1 function again. GO TO 3.
5.
PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION B-II
Release accelerator pedal fully.
NOTE:
Never apply brake during releasing the accelerator pedal.
Which does “TESTING” change to?
COMPLETED>>GO TO 6.
OUT OF CONDITION>>Retry DTC CONFIRMATION PROCEDURE. GO TO 4.
6.
PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION B-III
Touch “SELF-DIAG RESULT”
Which is displayed on CONSULT screen?
YES
>> INSPECTION END
NO
>> Proceed to
.
7.
PERFORM COMPONENT FUNCTION CHECK FOR MALFUNCTION B
Perform Component Function Check. Refer to
EC-225, "Component Function Check"
NOTE:
Use component function check to check the overall function of the A/F sensor 1 circuit. During this check, a
1st trip DTC might not be confirmed.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Proceed to
.
Component Function Check
INFOID:0000000007577098
1.
PERFORM COMPONENT FUNCTION CHECK
With GST
1.
Start engine and warm it up to normal operating temperature.
2.
Drive the vehicle at a speed of 80 km/h (50 MPH) for a few minutes in the suitable gear position.
3.
Shift the selector lever to the D position (CVT) or 5th position (M/T), then release the accelerator pedal
fully until the vehicle speed decreases to 50 km/h (31 MPH).
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
Never apply brake during releasing the accelerator pedal.
4.
Repeat steps 2 to 3 for five times.
5.
Stop the vehicle and turn ignition switch OFF.
6.
Wait at least 10 seconds and restart engine.
7.
Repeat steps 2 to 3 for five times.
8.
Stop the vehicle.
9.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007577099
1.
CHECK AIR FUEL RATIO (A/F) SENSOR 1 POWER SUPPLY
1.
Turn ignition switch OFF.
2.
Disconnect A/F sensor 1 harness connector.
3.
Turn ignition switch ON.
Revision: 2011 October
2012 JUKE
EC-226
< DTC/CIRCUIT DIAGNOSIS >
[MR16DDT ]
P0130 A/F SENSOR 1
4.
Check the voltage between A/F sensor 1 harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK AIR FUEL RATIO (A/F) SENSOR 1 POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R harness connector.
3.
Check the continuity between A/F sensor 1 harness connector and IPDM E/R harness connector.
4.
Also check harness for short to ground.
Is the inspection result normal?
YES
>> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
3.
CHECK A/F SENSOR 1 INPUT SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check the continuity between A/F sensor 1 harness connector and ECM harness connector.
4.
Check the continuity between A/F sensor 1 harness connector and ground, or ECM harness connector
and ground.
5.
Also check harness for short to power.
Is the inspection result normal?
+
−
Voltage
A/F sensor 1
Connector
Terminal
F70
4
Ground
Battery voltage
+
−
Continuity
A/F sensor 1
IPDM E/R
Connector
Terminal
Connector
Terminal
F70
4
E14
36
Existed
+
−
Continuity
A/F sensor 1
ECM
Connector
Terminal
Connector
Terminal
F70
1
F25
21
Existed
2
25
+
−
Continuity
A/F sensor 1
Connector
Terminal
F70
1
Ground
Not existed
2
+
−
Continuity
ECM
Connector
Terminal
F25
21
Ground
Not existed
25
Revision: 2011 October
2012 JUKE
P0130 A/F SENSOR 1
EC-227
< DTC/CIRCUIT DIAGNOSIS >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
YES
>> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.
CHECK INTERMITTENT INCIDENT
Perform
GI-43, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace error-detected parts.
5.
REPLACE AIR FUEL RATIO (A/F) SENSOR 1
Replace air fuel ratio (A/F) sensor 1. Refer to
CAUTION:
• Discard any sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a hard
surface such as a concrete floor; use a new one.
• Before installing new sensor, clean exhaust system threads using Oxygen Sensor Thread Cleaner
[commercial service tool (J-43897-18 or J43897-12)] and approved Anti-seize Lubricant (commercial
service tool).
>> INSPECTION END
Revision: 2011 October
2012 JUKE
EC-228
< DTC/CIRCUIT DIAGNOSIS >
[MR16DDT ]
P0131 A/F SENSOR 1
P0131 A/F SENSOR 1
DTC Logic
INFOID:0000000007577100
DTC DETECTION LOGIC
To judge the malfunction, the diagnosis checks that the A/F signal computed by ECM from the A/F sensor 1
signal is not inordinately low.
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 10.5 V at idle.
>> GO TO 2.
2.
CHECK A/F SENSOR FUNCTION
With CONSULT
1.
Start engine and warm it up to normal operating temperature.
2.
Select “A/F SEN1 (B1)” in “DATA MONITOR” mode of “ENGINE” using CONSULT.
3.
Check “A/F SEN1 (B1)” indication.
With GST
Follow the procedure “With CONSULT” above.
Is the indication constantly approx. 0 V?
YES
>> Proceed to
.
NO
>> GO TO 3.
3.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1.
Turn ignition switch OFF, wait at least 10 seconds and then restart engine.
2.
Drive and accelerate vehicle to more than 40 km/h (25 MPH) within 20 seconds after restarting engine.
CAUTION:
Always drive vehicle at a safe speed.
3.
Maintain the following conditions for about 20 consecutive seconds.
NOTE:
• Keep the accelerator pedal as steady as possible during the cruising.
• If this procedure is not completed within 1 minute after restarting engine at step 1, return to step
1.
4.
Check 1st trip DTC.
With GST
DTC No.
Trouble diagnosis name
(Trouble diagnosis content)
DTC detecting condition
Possible Cause
P0131
A/F SENSOR1 (B1)
[Air fuel ratio (A/F) sensor 1
circuit low voltage]
The A/F signal computed by ECM from the A/F
sensor 1 signal is constantly approx. 0 V.
• Harness or connectors
(A/F sensor 1 circuit is open or
shorted.)
• A/F sensor 1
ENG SPEED
1,000 - 3,200 rpm
VHCL SPEED SE
More than 40 km/h (25 mph)
B/FUEL SCHDL
1.5 - 9.0 msec
Selector lever
Suitable position
Revision: 2011 October
2012 JUKE
P0131 A/F SENSOR 1
EC-229
< DTC/CIRCUIT DIAGNOSIS >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Follow the procedure “With CONSULT” above.
Is 1st trip DTC detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007577101
1.
CHECK AIR FUEL RATIO (A/F) SENSOR 1 POWER SUPPLY
1.
Turn ignition switch OFF.
2.
Disconnect A/F sensor 1 harness connector.
3.
Turn ignition switch ON.
4.
Check the voltage between A/F sensor 1 harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK AIR FUEL RATIO (A/F) SENSOR 1 POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R harness connector.
3.
Check the continuity between A/F sensor 1 harness connector and IPDM E/R harness connector.
4.
Also check harness for short to ground.
Is the inspection result normal?
YES
>> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
3.
CHECK A/F SENSOR 1 INPUT SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check the continuity between A/F sensor 1 harness connector and ECM harness connector.
4.
Check the continuity between A/F sensor 1 harness connector and ground, or ECM harness connector
and ground.
+
−
Voltage
A/F sensor 1
Connector
Terminal
F70
4
Ground
Battery voltage
+
−
Continuity
A/F sensor 1
IPDM E/R
Connector
Terminal
Connector
Terminal
F70
4
E14
36
Existed
+
−
Continuity
A/F sensor 1
ECM
Connector
Terminal
Connector
Terminal
F70
1
F25
21
Existed
2
25
Revision: 2011 October
2012 JUKE
EC-230
< DTC/CIRCUIT DIAGNOSIS >
[MR16DDT ]
P0131 A/F SENSOR 1
5.
Also check harness for short to power.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.
CHECK INTERMITTENT INCIDENT
Perform
GI-43, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace error-detected parts.
5.
REPLACE AIR FUEL RATIO (A/F) SENSOR 1
Replace air fuel ratio (A/F) sensor 1. Refer to
CAUTION:
• Discard any sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a hard
surface such as a concrete floor; use a new one.
• Before installing new sensor, clean exhaust system threads using Oxygen Sensor Thread Cleaner
[commercial service tool (J-43897-18 or J43897-12)] and approved Anti-seize Lubricant (commercial
service tool).
>> INSPECTION END
+
−
Continuity
A/F sensor 1
Connector
Terminal
F70
1
Ground
Not existed
2
+
−
Continuity
ECM
Connector
Terminal
F25
21
Ground
Not existed
25
Revision: 2011 October
2012 JUKE
P0132 A/F SENSOR 1
EC-231
< DTC/CIRCUIT DIAGNOSIS >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P0132 A/F SENSOR 1
DTC Logic
INFOID:0000000007577102
DTC DETECTION LOGIC
To judge the malfunction, the diagnosis checks that the A/F signal computed by ECM from the A/F sensor 1
signal is not inordinately high.
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 10.5 V at idle.
>> GO TO 2.
2.
CHECK A/F SENSOR FUNCTION
With CONSULT
1.
Start engine and warm it up to normal operating temperature.
2.
Select “A/F SEN1 (B1)” in “DATA MONITOR” mode of “ENGINE” using CONSULT.
3.
Check “A/F SEN1 (B1)” indication.
With GST
Follow the procedure “With CONSULT” above.
Is the indication constantly approx. 5 V?
YES
>> Proceed to
.
NO
>> GO TO 3.
3.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1.
Turn ignition switch OFF, wait at least 10 seconds and then restart engine.
2.
Drive and accelerate vehicle to more than 40 km/h (25 MPH) within 20 seconds after restarting engine.
CAUTION:
Always drive vehicle at a safe speed.
3.
Maintain the following conditions for about 20 consecutive seconds.
NOTE:
• Keep the accelerator pedal as steady as possible during the cruising.
• If this procedure is not completed within 1 minute after restarting engine at step 1, return to step
1.
4.
Check 1st trip DTC.
With GST
DTC No.
Trouble diagnosis name
(Trouble diagnosis content)
DTC detecting condition
Possible Cause
P0132
A/F SENSOR1 (B1)
[Air fuel ratio (A/F) sensor 1
circuit high voltage]
The A/F signal computed by ECM from the A/F
sensor 1 signal is constantly approx. 5 V.
• Harness or connectors
(A/F sensor 1 circuit is open or short-
ed.)
• A/F sensor 1
ENG SPEED
1,000 - 3,200 rpm
VHCL SPEED SE
More than 40 km/h (25 mph)
B/FUEL SCHDL
1.5 - 9.0 msec
Selector lever
Suitable position
Revision: 2011 October
2012 JUKE
EC-232
< DTC/CIRCUIT DIAGNOSIS >
[MR16DDT ]
P0132 A/F SENSOR 1
Follow the procedure “With CONSULT” above.
Is 1st trip DTC is detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007577103
1.
CHECK AIR FUEL RATIO (A/F) SENSOR 1 POWER SUPPLY
1.
Turn ignition switch OFF.
2.
Disconnect A/F sensor 1 harness connector.
3.
Turn ignition switch ON.
4.
Check the voltage between A/F sensor 1 harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK AIR FUEL RATIO (A/F) SENSOR 1 POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R harness connector.
3.
Check the continuity between A/F sensor 1 harness connector and IPDM E/R harness connector.
4.
Also check harness for short to ground.
Is the inspection result normal?
YES
>> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
3.
CHECK A/F SENSOR 1 INPUT SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check the continuity between A/F sensor 1 harness connector and ECM harness connector.
4.
Check the continuity between A/F sensor 1 harness connector and ground, or ECM harness connector
and ground.
+
−
Voltage
A/F sensor 1
Connector
Terminal
F70
4
Ground
Battery voltage
+
−
Continuity
A/F sensor 1
IPDM E/R
Connector
Terminal
Connector
Terminal
F70
4
E14
36
Existed
+
−
Continuity
A/F sensor 1
ECM
Connector
Terminal
Connector
Terminal
F70
1
F25
21
Existed
2
25
Revision: 2011 October
2012 JUKE
P0132 A/F SENSOR 1
EC-233
< DTC/CIRCUIT DIAGNOSIS >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
5.
Also check harness for short to power.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.
CHECK INTERMITTENT INCIDENT
Perform
GI-43, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace error-detected parts.
5.
REPLACE AIR FUEL RATIO (A/F) SENSOR 1
Replace air fuel ratio (A/F) sensor 1. Refer to
CAUTION:
• Discard any sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a hard
surface such as a concrete floor; use a new one.
• Before installing new sensor, clean exhaust system threads using Oxygen Sensor Thread Cleaner
[commercial service tool (J-43897-18 or J43897-12)] and approved Anti-seize Lubricant (commercial
service tool).
>> INSPECTION END
+
−
Continuity
A/F sensor 1
Connector
Terminal
F70
1
Ground
Not existed
2
+
−
Continuity
ECM
Connector
Terminal
F25
21
Ground
Not existed
25
Revision: 2011 October
2012 JUKE
EC-234
< DTC/CIRCUIT DIAGNOSIS >
[MR16DDT ]
P0133 A/F SENSOR 1
P0133 A/F SENSOR 1
DTC Logic
INFOID:0000000007577104
DTC DETECTION LOGIC
To judge the malfunction of A/F sensor 1, this diagnosis measures response time of the A/F signal computed
by ECM from the A/F sensor 1 signal. The time is compensated by engine operating (speed and load), fuel
feedback control constant, and the A/F sensor 1 temperature index. Judgment is based on whether the com-
pensated time (the A/F signal cycling time index) is inordinately long or not.
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.
Do you have CONSULT?
YES
>> GO TO 2.
NO
>> GO TO 5.
2.
PERFORM DTC CONFIRMATION PROCEDURE-I
With CONSULT
1.
Start engine and warm it up to normal operating temperature.
2.
Turn ignition switch OFF and wait at least 10 seconds.
3.
Restart engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1minute under no
load.
4.
Let engine idle for 1 minute.
5.
Select “ENGINE” using CONSULT.
6.
Select “A/F SEN1(B1) P1278/P1279” (for DTC P0133) of “A/F SEN1” in “DTC WORK SUPPORT” mode.
7.
Touch “START”.
Is “COMPLETED” displayed on CONSULT screen?
YES
>> GO TO 3
NO
>> GO TO 4.
3.
PERFORM DTC CONFIRMATION PROCEDURE-II
Touch “SELF-DIAG RESULT”.
Which is displayed on CONSULT screen?
OK
>> INSPECTION END
NG
>> Proceed to
.
4.
PERFORM DTC CONFIRMATION PROCEDURE-II
1.
After perform the following procedure, “TESTING” will be displayed on the CONSULT screen.
DTC No.
Trouble diagnosis name
(Trouble diagnosis content)
DTC detecting condition
Possible Cause
P0133
A/F SENSOR1 (B1)
[Air fuel ratio (A/F) sensor 1
circuit slow response]
The response of the A/F signal computed by ECM
from A/F sensor 1 signal takes more than the
specified time.
• Harness or connectors
(A/F sensor 1 circuit is open or
shorted.)
• A/F sensor 1
• A/F sensor 1 heater
• Fuel pressure
• Fuel injector
• Intake air leaks
• Exhaust gas leaks
• PCV
• Mass air flow sensor
Revision: 2011 October
2012 JUKE
P0133 A/F SENSOR 1
EC-235
< DTC/CIRCUIT DIAGNOSIS >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
-
Increase the engine speed up to between 4,000 and 5,000 rpm and maintain that speed for 10 seconds.
-
Fully release accelerator pedal and then let engine idle for about 10 seconds.
If “TESTING” is not displayed after 10 seconds, refer to
EC-225, "Component Function Check"
2.
Wait for about 20 seconds at idle as per the condition that “TESTING” is displayed on the CONSULT
screen.
3.
Make sure that “TESTING” changes to “COMPLETED”.
If “TESTING” changed to “OUT OF CONDITION”, refer to
EC-225, "Component Function Check"
4.
Touch “SELF-DIAG RESULT”.
Which is displayed on CONSULT screen?
OK
>> INSPECTION END
NG
>> Proceed to
.
5.
CHECK AIR-FUEL RATIO SELF-LEARNING VALUE
With GST
1.
Start engine and warm it up to normal operating temperature.
2.
Select Service $01 with GST.
3.
Calculate the total value of “Short term fuel trim” and “Long term fuel trim” indications.
Is the total percentage within
±
15%?
YES
>> GO TO 7.
NO
>> GO TO 6.
6.
DETECT MALFUNCTIONING PART
Check the following.
• Intake air leaks
• Exhaust gas leaks
• Incorrect fuel pressure
• Lack of fuel
• Fuel injector
• Incorrect PCV hose connection
• PCV valve
• Mass air flow sensor
>> Repair or replace malfunctioning part.
7.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Restart engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1minute under no
load.
3.
Let engine idle for 1 minute.
4.
Increase the engine speed up to between 4,000 and 5,000 rpm and maintain that speed for 10 seconds.
5.
Fully release accelerator pedal and then let engine idle for about 1 minute.
6.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007577105
1.
RETIGHTEN A/F SENSOR 1
Loosen and retighten the A/F sensor 1. Refer to
>> GO TO 2.
2.
CHECK EXHAUST GAS LEAK
1.
Start engine and run it at idle.
Revision: 2011 October
2012 JUKE
EC-236
< DTC/CIRCUIT DIAGNOSIS >
[MR16DDT ]
P0133 A/F SENSOR 1
2.
Listen for an exhaust gas leak before three way catalyst 1.
Is exhaust gas leak detected?
YES
>> Repair or replace.
NO
>> GO TO 3.
3.
CHECK FOR INTAKE AIR LEAK
Listen for an intake air leak after the mass air flow sensor.
Is intake air leak detected?
YES
>> Repair or replace.
NO
>> GO TO 4.
4.
CLEAR THE MIXTURE RATIO SELF-LEARNING VALUE
1.
Clear the mixture ratio self-learning value. Refer to
.
2.
Run engine for at least 10 minutes at idle speed.
Is the 1st trip DTC P0171 or P0172 detected? Is it difficult to start engine?
YES
>> Perform trouble diagnosis for DTC P0171 or P0172. Refer to
NO
>> GO TO 5.
5.
CHECK AIR FUEL RATIO (A/F) SENSOR 1 POWER SUPPLY
1.
Turn ignition switch OFF.
2.
Disconnect A/F sensor 1 harness connector.
3.
Turn ignition switch ON.
4.
Check the voltage between A/F sensor 1 harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> GO TO 6.
6.
CHECK A/F SENSOR 1 INPUT SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R harness connector.
3.
Check the continuity between A/F sensor 1 harness connector and IPDM E/R harness connector.
4.
Also check harness for short to ground.
Is the inspection result normal?
YES
>> Perform the trouble diagnosis for power supply circuit.
PBIB1216E
+
−
Voltage
A/F sensor 1
Connector
Terminal
F70
4
Ground
Battery voltage
+
-
Continuity
A/F sensor 1
IPDM E/R
Connector
Terminal
Connector
Terminal
F70
4
E14
36
Existed
Revision: 2011 October
2012 JUKE
P0133 A/F SENSOR 1
EC-237
< DTC/CIRCUIT DIAGNOSIS >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
NO
>> Repair or replace error-detected parts.
7.
CHECK A/F SENSOR 1 INPUT SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check the continuity between A/F sensor 1 harness connector and ECM harness connector.
4.
Check the continuity between A/F sensor 1 harness connector and ground or ECM harness connector
and ground.
5.
Also check harness for short to power.
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Repair or replace error-detected parts.
8.
CHECK AIR FUEL RATIO (A/F) SENSOR 1 HEATER
Check the air fuel ratio (A/F) sensor 1 heater. Refer to
EC-172, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> GO TO 12.
9.
CHECK MASS AIR FLOW SENSOR
Check the mass air flow sensor. Refer to
EC-196, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> Replace mass air flow sensor. Refer to
.
10.
CHECK PCV VALVE
Check the PCV valve. Refer to
.
Is the inspection result normal?
YES
>> GO TO 11.
NO
>> Repair or replace PCV valve. Refer to
11.
CHECK INTERMITTENT INCIDENT
Perform
GI-43, "Intermittent Incident"
.
Is the inspection result normal?
+
-
Continuity
A/F sensor 1
ECM
Connector
Terminal
Connector
Terminal
F70
1
F25
21
Existed
2
25
+
−
Continuity
A/F sensor 1
Connector
Terminal
F70
1
Ground
Not existed
2
+
−
Continuity
ECM
Connector
Terminal
F25
21
Ground
Not existed
25
Revision: 2011 October
2012 JUKE
EC-238
< DTC/CIRCUIT DIAGNOSIS >
[MR16DDT ]
P0133 A/F SENSOR 1
YES
>> GO TO 12.
NO
>> Repair or replace error-detected parts.
12.
REPLACE AIR FUEL RATIO (A/F) SENSOR 1
Replace malfunctioning air fuel ratio (A/F) sensor 1. Refer to
.
CAUTION:
• Discard any A/F sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a
hard surface such as a concrete floor; use a new one.
• Before installing new A/F sensor, clean exhaust system threads using Oxygen Sensor Thread
Cleaner (commercial service tool) and approved anti-seize lubricant (commercial service tool).
>> INSPECTION END
Revision: 2011 October
2012 JUKE
P0137 HO2S2
EC-239
< DTC/CIRCUIT DIAGNOSIS >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P0137 HO2S2
DTC Logic
INFOID:0000000007577106
DTC DETECTION LOGIC
The heated oxygen sensor 2 has a much longer switching time
between rich and lean than the air fuel ratio (A/F) sensor 1. The oxy-
gen storage capacity of the three way catalyst (manifold) causes the
longer switching time. To judge the malfunctions of heated oxygen
sensor 2, ECM monitors whether the maximum voltage of the sensor
is sufficiently high during the various driving condition such as fuel-
cut.
DTC CONFIRMATION PROCEDURE
1.
INSPECTION START
Do you have CONSULT?
Do you have CONSULT?
YES
>> GO TO 2.
NO
>> GO TO 5.
2.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
For better results, perform “DTC WORK SUPPORT” at a temperature of 0 to 30
°
C (32 to 86
°
F).
>> GO TO 3.
3.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1.
Turn ignition switch ON and select “DATA MONITOR” mode of “ENGINE” using CONSULT.
2.
Start engine and warm it up to normal operating temperature.
3.
Turn ignition switch OFF and wait at least 10 seconds.
4.
Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no load.
5.
Let engine idle for 1 minute.
6.
Make sure that “COOLAN TEMP/S” indicates more than 70
°
C (158
°
F).
If not, warm up engine and go to next step when “COOLAN TEMP/S” indication reaches 70
°
C (158
°
F).
7.
Open engine hood.
8.
Select “HO2S2 (B1) P1147” of “HO2S2” in “DTC WORK SUPPORT” mode of “ENGINE” using CONSULT.
SEF259VA
DTC No.
Trouble diagnosis name
(Trouble diagnosis con-
tent)
DTC detecting condition
Possible cause
P0137
HO2S2 (B1)
(Heated oxygen sensor
2 circuit low voltage)
The maximum voltage from the heated oxygen
sensor 2 is not reached to the specified voltage.
• Harness or connectors
(Heated oxygen sensor 2 circuit is open
or shorted)
• Heated oxygen sensor 2
• Fuel pressure
• Fuel injector
• Intake air leaks
Revision: 2011 October
2012 JUKE
EC-240
< DTC/CIRCUIT DIAGNOSIS >
[MR16DDT ]
P0137 HO2S2
9.
Follow the instruction of CONSULT.
NOTE:
It will take at most 10 minutes until “COMPLETED” is displayed.
10. Touch “SELF-DIAG RESULT”.
Which is displayed on CONSULT screen?
OK
>> INSPECTION END
NG
>> Proceed to
.
CAN NOT BE DIAGNOSED>>GO TO 4.
4.
PERFORM DTC CONFIRMATION PROCEDURE AGAIN
1.
Turn ignition switch OFF and leave the vehicle in a cool place (soak the vehicle).
2.
Perform DTC CONFIRMATION PROCEDURE again.
>> GO TO 3.
5.
PERFORM COMPONENT FUNCTION CHECK
Perform component function check. Refer to
EC-240, "Component Function Check"
NOTE:
Use component function check to check the overall function of the heated oxygen sensor 2 circuit. During this
check, a 1st trip DTC might not be confirmed.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Proceed to
.
Component Function Check
INFOID:0000000007577107
1.
PERFORM COMPONENT FUNCTION CHECK-I
Without CONSULT
1.
Start engine and warm it up to normal operating temperature.
2.
Turn ignition switch OFF and wait at least 10 seconds.
3.
Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no load.
4.
Let engine idle for 1 minute.
5.
Check the voltage between ECM harness connector and ground as per the following condition.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
PERFORM COMPONENT FUNCTION CHECK-II
Check the voltage between ECM harness connector and ground as per the following condition.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 3.
ECM
Condition
Voltage
Connector
+
−
Terminal
F25
29
33
Revving up to 4,000 rpm under no
load at least 10 times
The voltage should be above 0.68 V
at least once during this procedure.
ECM
Condition
Voltage
Connector
+
−
Terminal
F25
29
33
Keeping engine speed at idle for 10
minutes
The voltage should be above 0.68 V
at least once during this procedure.
Revision: 2011 October
2012 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст