Nissan Juke (2012 year). Service Repair Manual — part 13
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-27
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
SELF-DIAG RESULT
DATA MONITOR
ANS BACK I-KEY UNLOCK
Buzzer reminder function (unlock operation) mode by door request switch can be changed to
operation with this mode
• On: Operate
• Off: Non-operation
SHORT CRANKING OUTPUT
Starter motor can operate during the times below
• 70 msec
• 100 msec
• 200 msec
CONFIRM KEY FOB ID
It can be checked whether Intelligent Key ID code is registered or not in this mode
AUTO LOCK SET
Auto door lock operation time can be changed in this mode
• MODE 1: OFF
• MODE 2: 30 sec
• MODE 3: 1 minute
• MODE 4: 2 minutes
• MODE 5: 3 minutes
• MODE 6: 4 minutes
• MODE 7: 5 minutes
Monitor item
Description
Monitor Item
Condition
REQ SW -DR
Indicates [On/Off] condition of door request switch (driver side)
REQ SW -AS
Indicates [On/Off] condition of door request switch (passenger side)
REQ SW -BD/TR
Indicates [On/Off] condition of back door request switch
PUSH SW
Indicates [On/Off] condition of push-button ignition switch
CLUTCH SW*
1
Indicates [On/Off] condition of clutch interlock switch
BRAKE SW 1
Indicates [On/Off]*
2
condition of stop lamp switch power supply
BRAKE SW 2
Indicates [On/Off] condition of stop lamp switch
DETE/CANCL SW
Indicates [On/Off] condition of P position
SFT PN/N SW
Indicates [On/Off] condition of P or N position
UNLK SEN -DR
Indicates [On/Off] condition of driver door UNLOCK status
PUSH SW -IPDM
Indicates [On/Off] condition of push-button ignition switch
IGN RLY1 -F/B
Indicates [On/Off] condition of ignition relay 1
DETE SW -IPDM
Indicates [On/Off] condition of P position
SFT PN -IPDM
Indicates [On/Off] condition of P or N position
SFT P -MET
Indicates [On/Off] condition of P position
SFT N -MET
Indicates [On/Off] condition of N position
ENGINE STATE
Indicates [Stop/Stall/Crank/Run] condition of engine states
S/L LOCK-IPDM
NOTE:
This item is displayed, but cannot be monitored
S/L UNLK-IPDM
NOTE:
This item is displayed, but cannot be monitored
S/L RELAY-REQ
NOTE:
This item is displayed, but cannot be monitored
VEH SPEED 1
Display the vehicle speed signal received from combination meter by numerical value [Km/h]
VEH SPEED 2
Display the vehicle speed signal received from ABS or VDC or TCM by numerical value [Km/h]
DOOR STAT-DR
Indicates [LOCK/READY/UNLK] condition of driver side door status
DOOR STAT-AS
Indicates [LOCK/READY/UNLK] condition of passenger side door status
Revision: 2011 October
2012 JUKE
BCS-28
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
*
1
: It is displayed but does not operate on CVT models.
*
2
: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.
ACTIVE TEST
ID OK FLAG
Indicates [Set/Reset] condition of key ID
PRMT ENG STRT
Indicates [Set/Reset] condition of engine start possibility
PRMT RKE STRT
NOTE:
This item is displayed, but cannot be monitored
TRNK/HAT MNTR
NOTE:
This item is displayed, but cannot be monitored
RKE-LOCK
Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
RKE-PANIC
Indicates [On/Off] condition of PANIC button of Intelligent Key
RKE-MODE CHG
Indicates [On/Off] condition of MODE CHANGE signal from Intelligent Key
RKE OPE COUN1
When remote keyless entry receiver receives the signal transmitted while operating on Intelli-
gent Key, the numerical value start changing
RKE OPE COUN2
NOTE:
This item is displayed, but cannot be monitored
Monitor Item
Condition
Test item
Description
OUTSIDE BUZZER
This test is able to check Intelligent Key warning buzzer operation
• On: Operate
• Off: Non-operation
INSIDE BUZZER
This test is able to check warning chime in combination meter operation
• Take Out: Take away warning chime sounds when CONSULT screen is touched
• Key: Key warning chime sounds when CONSULT screen is touched
• Knob: OFF position warning chime sounds when CONSULT screen is touched
• Off: Non-operation
INDICATOR
This test is able to check warning lamp operation
• KEY ON: “KEY” Warning lamp illuminates when CONSULT screen is touched
• KEY IND: “KEY” Warning lamp blinks when CONSULT screen is touched
• Off: Non-operation
INT LAMP
This test is able to check interior room lamp operation
• On: Operate
• Off: Non-operation
LCD
This test is able to check meter display information
• BP N: Engine start operation indicator lamp indicate when CONSULT screen is touched
• BP I: Engine start operation indicator lamp indicate when CONSULT screen is touched
• ID NG: This item is displayed, but cannot be monitored
• ROTAT: This item is displayed, but cannot be monitored
• SFT P: Shift P warning lamp indicate when CONSULT screen is touched
• INSRT: This item is displayed, but cannot be monitored
• BATT: Key warning lamp indicator when CONSULT screen is touched
• NO KY: Key warning lamp indicator when CONSULT screen is touched
• OUTKEY: Engine start operation indicator lamp indicate when CONSULT screen is touched
• LK WN: Engine start operation indicator lamp indicate when CONSULT screen is touched
FLASHER
This test is able to check security hazard lamp operation
The hazard lamps are activated after “LH/RH/Off” on CONSULT screen is touched
HORN
This test is able to check horn operation
The horn is activated after “ON” on CONSULT screen is touched
P RANGE
This test is able to check CVT shift selector power supply
• On: Operate
• Off: Non-operation
Revision: 2011 October
2012 JUKE
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-29
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
COMB SW
COMB SW : CONSULT Function (BCM - COMB SW)
INFOID:0000000007576654
DATA MONITOR
BCM
BCM : CONSULT Function (BCM - BCM)
INFOID:0000000007576655
WORK SUPPORT
IMMU
ENGINE SW ILLUMI
This test is able to check push-ignition switch illumination operation
Push-ignition switch illumination illuminates when “ON” on CONSULT screen is touched
PUSH SWITCH INDICATOR
This test is able to check LOCK indicator in push-ignition switch operation
LOCK indicator in push-ignition switch illuminates when “ON” on CONSULT screen is touched
BATTERY SAVER
This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT screen is touched.
TRUNK/BACK DOOR
This test is able to check back door opener actuator open operation.
This actuator opens when “Open” on CONSULT screen is touched.
Test item
Description
Monitor item [UNIT]
Description
FR WIPER HI
[Off/On]
Displays the status of the FR WIPER HI switch in combination switch judged by BCM with the combination
switch reading function.
FR WIPER LOW
[Off/On]
Displays the status of the FR WIPER LOW switch in combination switch judged by BCM with the combination
switch reading function.
FR WASHER SW
[Off/On]
Displays the status of the FR WASHER switch in combination switch judged by BCM with the combination
switch reading function.
FR WIPER INT
[Off/On]
Displays the status of the FR WIPER INT switch in combination switch judged by BCM with the combination
switch reading function.
INT VOLUME
[1 - 7]
Displays the status of wiper volume dial position judged by BCM with the combination switch reading function.
TURN SIGNAL R
[Off/On]
Displays the status of the TURN RH switch in combination switch judged by BCM with the combination switch
reading function.
TURN SIGNAL L
[Off/On]
Displays the status of the TURN LH switch in combination switch judged by BCM with the combination switch
reading function.
TAIL LAMP SW
[Off/On]
Displays the status of the TAIL LAMP switch in combination switch judged by BCM with the combination
switch reading function.
HI BEAM SW
[Off/On]
Displays the status of the HI BEAM switch in combination switch judged by BCM with the combination switch
reading function.
HEAD LAMP SW 1
[Off/On]
Displays the status of the HEADLAMP 1 switch in combination switch judged by BCM with the combination
switch reading function.
HEAD LAMP SW 2
[Off/On]
Displays the status of the HEADLAMP 2 switch in combination switch judged by BCM with the combination
switch reading function.
PASSING SW
[Off/On]
Displays the status of the PASSING switch in combination switch judged by BCM with the combination switch
reading function.
AUTO LIGHT SW
[Off/On]
Displays the status of the AUTO LIGHT switch in combination switch judged by BCM with the combination
switch reading function.
FR FOG SW
[Off/On]
Displays the status of the FR FOG switch in combination switch judged by BCM with the combination switch
reading function.
Item
Description
RESET SETTING VALUE
Return a value set with Work Support of each system to a default value in factory shipment.
Revision: 2011 October
2012 JUKE
BCS-30
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
IMMU : CONSULT Function (BCM - IMMU)
INFOID:0000000007829419
WORK SUPPORT
DATA MONITOR
ACTIVE TEST
BATTERY SAVER
BATTERY SAVER : CONSULT Function (BCM - BATTERY SAVER)
INFOID:0000000007829431
WORK SUPPORT
*:Factory setting
DATA MONITOR
Service item
Description
CONFIRM DONGLE ID
It is possible to check that dongle unit is applied to the vehicle.
Monitor item
Content
CONFRM ID ALL
Indicates [YET] at all time.
Switches to [DONE] when a registered Intelligent Key backside is contacted to push-button igni-
tion switch.
CONFIRM ID4
CONFIRM ID3
CONFIRM ID2
CONFIRM ID1
NOT REGISTERED
Indicates [ID OK] when key ID that is registered is received or is not yet received.
Indicates [ID NG] when key ID that is not registered is received.
TP 4
Indicates the number of IDs that are registered.
TP 3
TP 2
TP 1
PUSH SW
Indicates [ON/OFF] condition of push-button ignition switch.
Test item
Description
THEFT IND
This test is able to check security indicator lamp operation.
Security indicator lamp is turned on when “ON” on CONSULT screen is touched.
Service item
Setting item
Setting
ROOM LAMP TIMER SET
MODE 1
30 min.
Sets the interior room lamp battery saver timer operating
time.
MODE 2
60 min.
MODE 3
*
15 min.
BATTERY SAVER SET
On
*
With the exterior lamp battery saver function
Off
Without the exterior lamp battery saver function
ROOM LAMP BAT SAV SET
On
*
With the interior room lamp battery saver function
Off
Without the interior room lamp battery saver function
Revision: 2011 October
2012 JUKE
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-31
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ACTIVE TEST
*: Each lamp switch is in ON position.
TRUNK
TRUNK : CONSULT Function (BCM - TRUNK)
INFOID:0000000007829417
DATA MONITOR
Monitor item
[Unit]
Description
REQ SW-DR
[On/Off]
The switch status input from request switch (driver side)
REQ SW-AS
[On/Off]
The switch status input from request switch (passenger side)
REQ SW-RR
[On/Off]
NOTE:
The item is indicated, but not monitored.
REQ SW-RL
[On/Off]
PUSH SW
[On/Off]
Push switch status received from Intelligent Key unit by CAN communication
UNLK SEN -DR
[On/Off]
NOTE:
The item is indicated, but not monitored
DOOR SW-DR
[On/Off]
The switch status input from front door switch (driver side)
DOOR SW-AS
[On/Off]
The switch status input from front door switch (passenger side)
DOOR SW-RR
[On/Off]
The switch status input from rear door switch RH
DOOR SW- RL
[On/Off]
The switch status input from rear door switch LH
DOOR SW- BK
[On/Off]
The switch status input from back door switch
CDL LOCK SW
[On/Off]
Lock switch status input from door lock and unlock switch
CDL UNLOCK SW
[On/Off]
Unlock switch status input from door lock and unlock switch
TRNK/HAT MNTR
[On/Off]
NOTE:
The item is indicated, but not monitored
KEY CYL LK-SW
[On/Off]
Lock switch status received from key cylinder switch
KEY CYL UN-SW
[On/Off]
Unlock switch status received from key cylinder switch
RKE-LOCK
[On/Off]
Lock signal status received from remote keyless entry receiver
RKE-UNLOCK
[On/Off]
Unlock signal status received from remote keyless entry receiver
Test item
Operation
Description
BATTERY SAVER
Off
Cuts the interior room lamp power supply to turn interior room lamps OFF.
On
Outputs the interior room lamp power supply to turn interior room lamps ON.*
Revision: 2011 October
2012 JUKE
BCS-32
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
THEFT ALM
THEFT ALM : CONSULT Function (BCM - THEFT)
INFOID:0000000007829418
WORK SUPPORT
DATA MONITOR
Monitor Item
Contents
PUSH SW
Indicates [On/Off] condition of push switch
UNLK SEN -DR
Indicates [On/Off] condition of unlock sensor
VEH SPEED 1
Indicates [Km/h] condition of vehicle speed signal from combination meter
TR/BD OPEN SW
Indicates [ON/OFF] condition of back door opener switch.
TRNK/HAT MNTR
NOTE:
This item is displayed, but cannot be monitored
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
Service Item
Description
SECURITY ALARM SET
This mode is able to confirm and change security alarm ON-OFF setting.
THEFT ALM TRG
The switch which triggered vehicle security alarm is recorded.
This mode is able to confirm and erase the record of vehicle security alarm.
The trigger data can be erased by touching “CLEAR” on CONSULT screen.
Monitored Item
Description
REQ SW -DR
Indicates [ON/OFF] condition of door request switch (driver side).
REQ SW -AS
Indicates [ON/OFF] condition of door request switch (passenger side).
REQ SW -RR
NOTE:
This is displayed even when it is not equipped.
REQ SW -RL
NOTE:
This is displayed even when it is not equipped.
REQ SW -BD/TR
Indicates [ON/OFF] condition of back door request switch.
PUSH SW
Indicates [ON/OFF] condition of push-button ignition switch
UNLK SEN -DR
Indicates [ON/OFF] condition of driver door UNLOCK status.
DOOR SW-DR
Indicates [ON/OFF] condition of front door switch (driver side).
DOOR SW-AS
Indicates [ON/OFF] condition of front door switch (passenger side).
DOOR SW-RR
Indicates [ON/OFF] condition of rear door switch RH.
DOOR SW-RL
Indicates [ON/OFF] condition of rear door switch LH.
DOOR SW-BK
Indicates [ON/OFF] condition of back door switch.
CDL LOCK SW
Indicates [ON/OFF] condition of lock signal from door lock/unlock switch.
CDL UNLOCK SW
Indicates [ON/OFF] condition of unlock signal from door lock/unlock switch.
KEY CYL LK-SW
Indicates [ON/OFF] condition of lock signal from door key cylinder.
KEY CYL UN-SW
Indicates [ON/OFF] condition of unlock signal from door key cylinder.
TR/BD OPEN SW
Indicates [ON/OFF] condition of back door opener switch.
TRNK/HAT MNTR
NOTE:
This is displayed even when it is not equipped.
RKE-LOCK
Indicates [ON/OFF] condition of LOCK signal from Intelligent Key.
RKE-UNLOCK
Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key.
RKE-TR/BD
NOTE:
This is displayed even when it is not equipped.
Revision: 2011 October
2012 JUKE
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-33
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ACTIVE TEST
RETAIND PWR
RETAIND PWR : CONSULT Function (BCM - RETAINED PWR)
INFOID:0000000007829420
DATA MONITOR
SIGNAL BUFFER
SIGNAL BUFFER : CONSULT Function (BCM - SIGNAL BUFFER)
INFOID:0000000007576661
DATA MONITOR
ACTIVE TEST
AIR PRESSURE MONITOR
AIR PRESSURE MONITOR : CONSULT Function (BCM - AIR PRESSURE MONI-
TOR)
INFOID:0000000007829440
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SELF DIAGNOSTIC RESULT
DATA MONITOR MODE
Test Item
Description
THEFT IND
This test is able to check security indicator lamp operation.
Security indicator lamp is turned on when “ON” on CONSULT screen is touched.
VEHICLE SECURITY HORN
This test is able to check horns operation.
Horns are activated for 0.5 seconds after “ON” on CONSULT screen is touched.
HEADLAMP(HI)
This test is able to check headlamp operation.
Headlamps are activated for 0.5 seconds after “ON” on CONSULT screen is touched.
FLASHER
This test is able to check hazard warning lamp operation.
Hazard warning lamps are activated after “ON” on CONSULT screen is touched.
Monitor Item
Description
DOOR SW-DR
Indicates [ON/OFF] condition of driver side door switch.
DOOR SW-AS
Indicates [ON/OFF] condition of passenger side door switch.
Monitor item [UNIT]
Description
PUSH SW
[Off/On]
Displays the status of the push-button ignition switch (push switch) judged by BCM.
Test item
Opera-
tion
Description
OIL PRESSURE SW
Off
NOTE:
This item is indicated, but not tested.
On
Diagnosis mode
Function Description
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Work Support
Components can be quickly and accurately adjusted.
Revision: 2011 October
2012 JUKE
BCS-34
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
ACTIVE TEST MODE
NOTE:
After completing the work below, perform an active test.
1.
Check ID registration state and perform self-diagnosis.
2.
Erase the self-diagnosis result history.
WORK SUPPORT
Monitor item (Unit)
Remarks
AIR PRESS FL
(kPa, kg/cm2 or Psi)
Tire pressure
AIR PRESS FR
(kPa, kg/cm2 or Psi)
AIR PRESS RR
(kPa, kg/cm2 or Psi)
AIR PRESS RL
(kPa, kg/cm2 or Psi)
ID REGST FL1
(Yet, Done)
Registration ID
ID REGST FR1
(Yet, Done)
ID REGST RR1
(Yet, Done)
ID REGST RL1
(Yet, Done)
WARNING LAMP
(On/Off)
Low tire pressure warning lamp
BUZZER
(On/Off)
NOTE:
This item is displayed, but cannot be use this item.
Item
Description
WARNING LAMP
Low tire pressure warning lamp can be turned ON arbitrarily.
ID REGIST WARNING
NOTE:
Displayed but not used in TPMS.
RUN FLAT TIRE W/L
NOTE:
Displayed but not used in TPMS.
RUN FLAT/T WARN BUZZER
NOTE:
Displayed but not used in TPMS.
FLASHER
Turn signal lamps can be turned ON arbitrarily.
HORN
This test is able to check to check that the horn sounds.
Item
Description
ID READ
Registered tire pressure sensor ID can be displayed.
ID REGIST
Tire pressure sensor ID can be registered.
Revision: 2011 October
2012 JUKE
BCS
BCM
BCS-35
< ECU DIAGNOSIS INFORMATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ECU DIAGNOSIS INFORMATION
BCM
Reference Value
INFOID:0000000007576663
VALUES ON THE DIAGNOSIS TOOL
CONSULT MONITOR ITEM
Monitor Item
Condition
Value/Status
FR WIPER HI
Other than front wiper switch HI
Off
Front wiper switch HI
On
FR WIPER LOW
Other than front wiper switch LO
Off
Front wiper switch LO
On
FR WASHER SW
Front washer switch OFF
Off
Front washer switch ON
On
FR WIPER INT
Other than front wiper switch INT
Off
Front wiper switch INT
On
FR WIPER STOP
Front wiper is not in STOP position
Off
Front wiper is in STOP position
On
INT VOLUME
Wiper intermittent dial is in a dial position 1 - 7
Wiper intermittent dial
position
RR WIPER ON
Other than rear wiper switch ON
Off
Rear wiper switch ON
On
RR WIPER INT
Other than rear wiper switch INT
Off
Rear wiper switch INT
On
RR WASHER SW
Rear washer switch OFF
Off
Rear washer switch ON
On
RR WIPER STOP
Rear wiper is in STOP position
Off
Rear wiper is not in STOP position
On
TURN SIGNAL R
Other than turn signal switch RH
Off
Turn signal switch RH
On
TURN SIGNAL L
Other than turn signal switch LH
Off
Turn signal switch LH
On
TAIL LAMP SW
Other than lighting switch 1ST and 2ND
Off
Lighting switch 1ST or 2ND
On
HI BEAM SW
Other than lighting switch HI
Off
Lighting switch HI
On
HEAD LAMP SW 1
Other than lighting switch 2ND
Off
Lighting switch 2ND
On
HEAD LAMP SW 2
Other than lighting switch 2ND
Off
Lighting switch 2ND
On
PASSING SW
Other than lighting switch PASS
Off
Lighting switch PASS
On
AUTO LIGHT SW
Other than lighting switch AUTO
Off
Lighting switch AUTO
On
FR FOG SW
Front fog lamp switch OFF
Off
Front fog lamp switch ON
On
Revision: 2011 October
2012 JUKE
BCS-36
< ECU DIAGNOSIS INFORMATION >
[WITH INTELLIGENT KEY SYSTEM]
BCM
DOOR SW-DR
Driver door closed
Off
Driver door opened
On
DOOR SW-AS
Passenger door closed
Off
Passenger door opened
On
DOOR SW-RR
Rear RH door closed
Off
Rear RH door opened
On
DOOR SW-RL
Rear LH door closed
Off
Rear LH door opened
On
DOOR SW-BK
Back door closed
Off
Back door opened
On
CDL LOCK SW
Other than power door lock switch LOCK
Off
Power door lock switch LOCK
On
CDL UNLOCK SW
Other than power door lock switch UNLOCK
Off
Power door lock switch UNLOCK
On
KEY CYL LK-SW
Other than driver door key cylinder LOCK position
Off
Driver door key cylinder LOCK position
On
KEY CYL UN-SW
Other than driver door key cylinder UNLOCK position
Off
Driver door key cylinder UNLOCK position
On
HAZARD SW
Hazard switch is OFF
Off
Hazard switch is ON
On
REAR DEF SW
Rear window defogger switch OFF
Off
Rear window defogger switch ON
On
TR/BD OPEN SW
Back door opener switch OFF
Off
While the back door opener switch is turned ON
On
TRNK/HAT MNTR
NOTE:
The item is indicated, but not monitored.
Off
FAN ON SIG
Blower fan OFF
Off
Blower fan ON
On
AIR COND SW
Air conditioner OFF (A/C switch indicator OFF)
Off
Air conditioner ON (A/C switch indicator ON)
On
RKE-LOCK
LOCK button of the key is not pressed
Off
LOCK button of the key is pressed
On
RKE-UNLOCK
UNLOCK button of the key is not pressed
Off
UNLOCK button of the key is pressed
On
RKE-TR/BD
NOTE:
The item is indicated, but not monitored.
Off
RKE-PANIC
PANIC button of the key is not pressed
Off
PANIC button of the key is pressed
On
RKE-MODE CHG
LOCK/UNLOCK button of the key is not pressed and held simultaneously
Off
LOCK/UNLOCK button of the key is pressed and held simultaneously
On
OPTI SEN (DTCT)
Bright outside of the vehicle
Close to 5 V
Dark outside of the vehicle
Close to 0 V
OPTI SEN (FILT)
Bright outside of the vehicle (Lighting switch AUTO)
Close to 5 V
Dark outside of the vehicle (Lighting switch AUTO)
Close to 1.50 V
Monitor Item
Condition
Value/Status
Revision: 2011 October
2012 JUKE
BCS
BCM
BCS-37
< ECU DIAGNOSIS INFORMATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
OPTICAL SENSOR
NOTE:
The item is indicated, but not monitored.
Off
RAIN SENSOR
NOTE:
The item is indicated, but not monitored.
Off
REQ SW -DR
Driver door request switch is not pressed
Off
Driver door request switch is pressed
On
REQ SW -AS
Passenger door request switch is not pressed
Off
Passenger door request switch is pressed
On
REQ SW -RR
NOTE:
The item is indicated, but not monitored.
Off
REQ SW -RL
NOTE:
The item is indicated, but not monitored.
Off
REQ SW -BD/TR
Back door request switch is not pressed
Off
Back door request switch is pressed
On
PUSH SW
Push-button ignition switch (push switch) is not pressed
Off
Push-button ignition switch (push switch) is pressed
On
CLUCH SW
The clutch pedal is not depressed.
Off
The clutch pedal is depressed
On
BRAKE SW 1
The brake pedal is not depressed
Off
The brake pedal is depressed
On
BRAKE SW 2
The brake pedal is depressed when No. 38 fuse is blown
Off
The brake pedal is not depressed when No. 38 fuse is blown, or No. 38
fuse is normal
On
DETE/CANCL SW
NOTE:
For M/T models this item is not
used.
Selector lever in P position
Release selector button
Off
Push selector button
On
Selector lever in any position other than P
SFT PN/N SW
• Selector lever in any position other than P and N (CVT models)
• Control lever in any position other than neutral (M/T models)
Off
• Selector lever in P or N position (CVT models)
• Control lever in neutral position (M/T models)
On
S/L -LOCK
NOTE:
The item is indicated, but not monitored.
Off
S/L -UNLOCK
NOTE:
The item is indicated, but not monitored.
Off
S/L RELAY-F/B
NOTE:
The item is indicated, but not monitored.
Off
UNLK SEN -DR
Driver door is locked
Off
Driver door is unlocked
On
PUSH SW -IPDM
Push-button ignition switch (push-switch) is not pressed
Off
Push-button ignition switch (push-switch) is pressed
On
IGN RLY1 -F/B
Ignition switch in OFF or ACC position
Off
Ignition switch in ON position
On
DETE SW -IPDM
NOTE:
For M/T models this item is not
used.
Selector lever in any position other than P
Off
Selector lever in P position
Push selector button
Release selector button
On
Monitor Item
Condition
Value/Status
Revision: 2011 October
2012 JUKE
BCS-38
< ECU DIAGNOSIS INFORMATION >
[WITH INTELLIGENT KEY SYSTEM]
BCM
SFT PN -IPDM
NOTE:
For M/T models this item is not
used.
Selector lever in any position other than P and N
Off
Selector lever in P or N position
On
SFT P -MET
NOTE:
For M/T models this item is not
used.
Selector lever in any position other than P
Off
Selector lever in P position
On
SFT N -MET
NOTE:
For M/T models this item is not
used.
Selector lever in any position other than N
Off
Selector lever in N position
On
ENGINE STATE
Engine stopped
Stop
While the engine stalls
Stall
At engine cranking
Crank
Engine running
Run
S/L LOCK-IPDM
NOTE:
The item is indicated, but not monitored.
Off
S/L UNLK-IPDM
NOTE:
The item is indicated, but not monitored.
Off
S/L RELAY-REQ
NOTE:
The item is indicated, but not monitored.
Off
VEH SPEED 1
While driving
Equivalent to speed-
ometer reading
VEH SPEED 2
While driving
Equivalent to speed-
ometer reading
DOOR STAT-DR
Driver door is locked
LOCK
Wait with selective unlock operation (60 seconds)
READY
Driver door is unlocked
UNLOCK
DOOR STAT-AS
Passenger door is locked
LOCK
Wait with selective unlock operation (60 seconds)
READY
Passenger door is unlocked
UNLOCK
ID OK FLAG
Driver side door is open after ignition switch is turned OFF
(Shift position is in the P position)
Reset
Ignition switch ON
Set
PRMT ENG STRT
The engine start is prohibited
Reset
The engine start is permitted
Set
PRMT RKE STRT
NOTE:
The item is indicated, but not monitored.
Reset
RKE OPE COUN1
During the operation of the key
Operation frequency
of the key
RKE OPE COUN2
NOTE:
The item is indicated, but not monitored.
—
CONFRM ID ALL
The key ID that the key slot receives is not recognized by any key ID reg-
istered to BCM.
Yet
The key ID that the key slot receives is recognized by any key ID regis-
tered to BCM.
Done
CONFIRM ID4
The key ID that the key slot receives is not recognized by the fourth key ID
registered to BCM.
Yet
The key ID that the key slot receives is recognized by the fourth key ID reg-
istered to BCM.
Done
Monitor Item
Condition
Value/Status
Revision: 2011 October
2012 JUKE
BCS
BCM
BCS-39
< ECU DIAGNOSIS INFORMATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
CONFIRM ID3
The key ID that the key slot receives is not recognized by the third key ID
registered to BCM.
Yet
The key ID that the key slot receives is recognized by the third key ID reg-
istered to BCM.
Done
CONFIRM ID2
The key ID that the key slot receives is not recognized by the second key
ID registered to BCM.
Yet
The key ID that the key slot receives is recognized by the second key ID
registered to BCM.
Done
CONFIRM ID1
The key ID that the key slot receives is not recognized by the first key ID
registered to BCM.
Yet
The key ID that the key slot receives is recognized by the first key ID reg-
istered to BCM.
Done
NOT REGISTERED
BCM detects registered key ID, or BCM does not detect key ID.
ID OK
BCM detects non-registration key ID.
ID NG
TP 4
The ID of fourth key is not registered to BCM
Yet
The ID of fourth key is registered to BCM
Done
TP 3
The ID of third key is not registered to BCM
Yet
The ID of third key is registered to BCM
Done
TP 2
The ID of second key is not registered to BCM
Yet
The ID of second key is registered to BCM
Done
TP 1
The ID of first key is not registered to BCM
Yet
The ID of first key is registered to BCM
Done
AIR PRESS FL
Ignition switch ON (Only when the signal from the transmitter is received)
Air pressure of front
LH tire
AIR PRESS FR
Ignition switch ON (Only when the signal from the transmitter is received)
Air pressure of front
RH tire
AIR PRESS RR
Ignition switch ON (Only when the signal from the transmitter is received)
Air pressure of rear
RH tire
AIR PRESS RL
Ignition switch ON (Only when the signal from the transmitter is received)
Air pressure of rear
LH tire
ID REGST FL1
ID of front LH tire transmitter is registered
Done
ID of front LH tire transmitter is not registered
Yet
ID REGST FR1
ID of front RH tire transmitter is registered
Done
ID of front RH tire transmitter is not registered
Yet
ID REGST RR1
ID of rear RH tire transmitter is registered
Done
ID of rear RH tire transmitter is not registered
Yet
ID REGST RL1
ID of rear LH tire transmitter is registered
Done
ID of rear LH tire transmitter is not registered
Yet
WARNING LAMP
Tire pressure indicator OFF
Off
Tire pressure indicator ON
On
BUZZER
Tire pressure warning alarm is not sounding
Off
Tire pressure warning alarm is sounding
On
Monitor Item
Condition
Value/Status
Revision: 2011 October
2012 JUKE
BCS-40
< ECU DIAGNOSIS INFORMATION >
[WITH INTELLIGENT KEY SYSTEM]
BCM
TERMINAL LAYOUT
PHYSICAL VALUES
JMMIA0323ZZ
Revision: 2011 October
2012 JUKE
BCS
BCM
BCS-41
< ECU DIAGNOSIS INFORMATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output
+
−
2
(L)
Ground
Combination switch
INPUT 5
Input
Combination
switch
(Wiper intermit-
tent dial 4)
All switches OFF
0 V
Turn signal switch RH
1.0 V
Lighting switch HI
Lighting switch 1ST
Lighting switch 2ND
2.0 V
3
(GR)
Ground
Combination switch
INPUT 4
Input
Combination
switch
(Wiper intermit-
tent dial 4)
All switches OFF
0 V
Turn signal switch LH
1.0 V
Lighting switch PASS
Lighting switch 2ND
Front fog lamp switch ON
0.8 V
4
(BR)
Ground
Combination switch
INPUT 3
Input
Combination
switch
(Wiper intermit-
tent dial 4)
All switches OFF
0 V
Front wiper switch LO
1.0 V
Front wiper switch MIST
Front wiper switch INT
Lighting switch AUTO
PKIB4958J
JPMIA0342JP
PKIB4958J
PKIB4956J
PKIB4958J
Revision: 2011 October
2012 JUKE
BCS-42
< ECU DIAGNOSIS INFORMATION >
[WITH INTELLIGENT KEY SYSTEM]
BCM
5
(G)
Ground
Combination switch
INPUT 2
Input
Combination
switch
All switches OFF
(Wiper intermittent dial 4)
0 V
Front washer switch ON
(Wiper intermittent dial 4)
1.0 V
Rear washer switch ON
(Wiper intermittent dial 4)
Any of the condition below
with all switches OFF
• Wiper intermittent dial 1
• Wiper intermittent dial 5
• Wiper intermittent dial 6
Rear wiper switch ON
(Wiper intermittent dial 4)
0.8 V
6
(W)
Ground
Combination switch
INPUT 1
Input
Combination
switch
All switches OFF
(Wiper intermittent dial 4)
0 V
Front wiper switch HI
(Wiper intermittent dial 4)
1.0 V
Rear wiper switch INT
(Wiper intermittent dial 4)
Wiper intermittent dial 3
(All switches OFF)
Any of the condition below
with all switches OFF
• Wiper intermittent dial 1
• Wiper intermittent dial 2
1.9 V
Any of the condition below
with all switches OFF
• Wiper intermittent dial 6
• Wiper intermittent dial 7
0.8 V
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output
+
−
PKIB4958J
PKIB4956J
PKIB4958J
PKIB4952J
PKIB4956J
Revision: 2011 October
2012 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст