Nissan Juke (2012 year). Service Repair Manual — part 238
WCS
DIAGNOSIS SYSTEM (COMBINATION METER)
WCS-15
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
TURN IND
[On/Off]
Status of turn indicator lamp detected from turn indicator signal is received from
BCM via CAN communication.
LIGHT IND
[On/Off]
Status of tail lamp indicator lamp detected from position light request signal is re-
ceived from BCM via CAN communication.
OIL W/L
[On/Off]
Status of oil pressure warning lamp detected from oil pressure warning lamp sig-
nal is received from ECM via CAN communication.
MIL
[On/Off]
Status of malfunction indicator lamp detected from malfunctioning indicator lamp
signal is received from ECM via CAN communication.
GLOW IND
[Off]
This item is displayed, but cannot be monitored.
C-ENG2 W/L
[Off]
This item is displayed, but cannot be monitored.
CRUISE IND
[On/Off]
Status of CRUISE indicator lamp detected from ASCD status signal is received
from ECM via CAN communication.
SET IND
[Off]
This item is displayed, but cannot be monitored.
CVT IND
[On/Off]
Status of CVT indicator lamp detected from CVT status signal is received from
TCM via CAN communication.
4WD W/L
[On/Off]
Status of AWD warning lamp judged from AWD warning lamp signal received from
AWD control module with CAN communication line.
4WD LOCK IND
[On/Off]
Status of AWD mode indicator lamp (AWD-V) judged from AWD mode indicator
signal received from AWD control module with CAN communication line.
FUEL W/L
[On/Off]
Low fuel warning status detected by the identified fuel level.
AIR PRES W/L
[On/Off]
Status of low tire pressure warning lamp judged from low tire pressure warning
lamp signal received from BCM from CAN communication line.
KEY G/Y W/L
[On/Off]
Status of KEY warning lamp (G/Y) detected from KEY warning lamp signal is re-
ceived from BCM via CAN communication.
KEY KNOB W/L
[On/Off]
Status of shift P warning lamp detected from shift P warning lamp signal is re-
ceived from BCM via CAN communication.
EPS W/L
[On/Off]
Status of EPS warning lamp detected from EPS warning lamp signal is received
from EPS control unit via CAN communication.
DPF W/L
[Off]
This item is displayed, but cannot be monitored.
LCD
[B&P N, B&P I, SFT P, BATT, NO KY,
LK WN]
*1
[C&P N, C&P I, SFT P, BATT, NO KY,
LK WN]
*2
Status of engine start operation indicator lamp, shift P warning lamp and KEY
warning lamp, detected from engine start operation indicator lamp signal, shift P
warning lamp signal and KEY warning lamp signal are received from BCM via
CAN communication.
SHIFT IND
[P, R, N, D, M1, M2, M3,
M4, M5, M6]
Status of shift position indicator judged from shift position signal received from
TCM with CAN communication line.
O/D OFF SW
[Off]
This item is displayed, but cannot be monitored.
M RANGE SW
[On/Off]
Status of manual mode switch.
NM RANGE SW
[On/Off]
Status of non-manual mode switch.
AT SFT UP SW
[On/Off]
Status of manual mode shift up switch.
AT SFT DWN SW
[On/Off]
Status of manual mode shift down switch.
Display item [Unit]
MAIN
SIGNALS
Description
Revision: 2011 October
2012 JUKE
WCS-16
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (COMBINATION METER)
• *1: CVT models
• *2: M/T models
NOTE:
Some items are not available according to vehicle specification.
W/L ON HISTORY
• Stores histories when warning/indicator lamp is turned on.
• “W/L ON HISTORY” indicates the “TIME” when the warning/indicator lamp is turned on.
• The “TIME” above is:
- 0: The condition that the warning/indicator lamp has been turned on 1 or more times after starting the engine
and waiting for 30 seconds.
- 1 - 39: The number of times the engine was restarted after the 0 condition.
- NO W/L ON HISTORY: Stores NO (0) turning on history of warning/indicator lamp.
NOTE:
• W/L ON HISTORY is not stored for approximately 30 seconds after the engine starts.
• Brake warning lamp does not store any history when the parking brake is applied or the brake fluid level gets
low.
Display Item
PKB SW
[On/Off]
Status of parking brake switch.
BUCKLE SW
[On/Off]
Status of seat belt buckle switch (driver side).
BRAKE SW
[Off]
This item is displayed, but cannot be monitored.
BRAKE OIL SW
[On/Off]
Status of brake fluid level switch.
A/C AMP CONN
[On/Off]
Status of A/C auto amp. connection recognition signal.
PASS BUCKLE SW
[Off]
This item is displayed, but cannot be monitored.
DISTANCE
[km]
Value of distance to empty calculated by combination meter.
OUTSIDE TEMP
[
°
C or
°
F]
Ambient temperature value converted from ambient sensor signal received from
ambient sensor.
NOTE:
This may not match with the temperature value indicated on the information dis-
play. (Because the information display value is a corrected value from the ambient
sensor input value.)
FUEL LOW SIG
[On/Off]
Status of fuel level low warning signal to output to AV control unit via CAN com-
munication.
BUZZER
[On/Off]
X
Buzzer status (in the combination meter) is detected from the buzzer output signal
received from each unit via CAN communication and the warning output condition
of the combination meter.
ASCD SPD BLNK
[On/Off]
Blinking status of ASCD or speed limiter set vehicle speed that is judged by the
ASCD status signal received from ECM via CAN communication.
ASCD STATUS
[Off, ASCD, CRUISE, SL ON, SL
SET]
Display status of ASCD and speed limiter status display judged by the ASCD sta-
tus signal received from ECM via CAN communication.
ASCD REQ SPD
[km/h/Off]
ASCD or speed limiter set vehicle speed value that is judged by the ASCD status
signal received from ECM via CAN communication.
TPMS PRESS L
[On/Off]
Status of low tire pressure warning judged from low tire pressure warning lamp
signal received from BCM with CAN communication line.
Display item [Unit]
MAIN
SIGNALS
Description
Revision: 2011 October
2012 JUKE
WCS
DIAGNOSIS SYSTEM (COMBINATION METER)
WCS-17
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
NOTE:
In items displayed on the CONSULT screen, only those listed in the above table are used.
Display item
Description
ABS W/L
Lighting history of ABS warning lamp.
VDC/TCS IND
Lighting history of VDC OFF indicator lamp.
SLIP IND
Lighting history of VDC warning lamp.
BRAKE W/L
Lighting history of brake warning lamp.
DOOR W/L
Lighting history of door open warning.
OIL W/L
Lighting history of oil pressure warning lamp.
C-ENG W/L
Lighting history of malfunction indicator lamp.
CRUISE IND
Lighting history of CRUISE indicator lamp.
CVT IND
Lighting history of CVT indicator lamp.
4WD W/L
Lighting history of AWD warning lamp.
FUEL W/L
Lighting history of low fuel level warning lamp.
AIR PRES W/L
Lighting history of low tire pressure warning lamp.
KEY G/Y W/L
Lighting history of KEY warning lamp (G/Y).
KEY KNOB W/L
Lighting history of Shift P warning lamp.
EPS W/L
Lighting history of EPS warning lamp.
Revision: 2011 October
2012 JUKE
WCS-18
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000007836784
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
NOTE:
*: For models with automatic A/C, this diagnosis mode is not used.
FREEZE FRAME DATA (FFD)
The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT.
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
×
Air conditioning system
AIR CONDITONER
×
×
*
• Intelligent Key system
• Engine start system
INTELLIGENT KEY
×
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
NVIS - NATS
IMMU
×
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Back door open
TRUNK
×
Theft warning alarm
THEFT ALM
×
×
×
RAP
RETAINED PWR
×
Signal buffer system
SIGNAL BUFFER
×
×
TPMS
AIR PRESSURE MONITOR
×
×
×
Revision: 2011 October
2012 JUKE
WCS
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
WCS-19
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
NOTE:
*: Power position shifts to “LOCK” from “OFF”, when ignition switch is in the OFF position, selector lever is in the P position (A/T models
and CVT models), and any of the following conditions are met.
• Closing door
• Opening door
• Door is locked using door request switch
• Door is locked using Intelligent Key
The power position shifts to “ACC” when the push-button ignition switch (push switch) is pushed at “LOCK”.
BUZZER
BUZZER : CONSULT Function (BCM - BUZZER)
INFOID:0000000007577841
CONSULT APPLICATION ITEMS
CONSULT screen item
Indication/Unit
Description
Vehicle Speed
km/h
Vehicle speed of the moment a particular DTC is detected
Odo/Trip Meter
km
Total mileage (Odometer value) of the moment a particular DTC is detected
Vehicle Condition
SLEEP>LOCK
Power position status of
the moment a particular
DTC is detected
While turning BCM status from low power consumption mode to
normal mode (Power position is “LOCK”*.)
SLEEP>OFF
While turning BCM status from low power consumption mode to
normal mode (Power position is “OFF”.)
LOCK>ACC
While turning power position from “LOCK”* *to “ACC”
ACC>ON
While turning power position from “ACC” to “IGN”
RUN>ACC
While turning power position from “RUN” to “ACC” (Vehicle is
stopping and selector lever is except P position.)
CRANK>RUN
While turning power position from “CRANKING” to “RUN” (From
cranking up the engine to run it)
RUN>URGENT
While turning power position from “RUN“ to “ACC” (Emergency
stop operation)
ACC>OFF
While turning power position from “ACC” to “OFF”
OFF>LOCK
While turning power position from “OFF” to “LOCK”*
OFF>ACC
While turning power position from “OFF” to “ACC”
ON>CRANK
While turning power position from “IGN” to “CRANKING”
OFF>SLEEP
While turning BCM status from normal mode (Power position is
“OFF”.) to low power consumption mode
LOCK>SLEEP
While turning BCM status from normal mode (Power position is
“LOCK”*.) to low power consumption mode
LOCK
Power position is “LOCK”*
OFF
Power position is “OFF” (Ignition switch OFF)
ACC
Power position is “ACC” (Ignition switch ACC)
ON
Power position is “IGN” (Ignition switch ON with engine stopped)
ENGINE RUN
Power position is “RUN” (Ignition switch ON with engine running)
CRANKING
Power position is “CRANKING” (At engine cranking)
IGN Counter
0 - 39
The number of times that ignition switch is turned ON after DTC is detected
• The number is 0 when a malfunction is detected now.
• The number increases like 1
→
2
→
3...38
→
39 after returning to the normal condition
whenever ignition switch OFF
→
ON.
• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
Test item
Diagnosis mode
Description
BUZZER
Data Monitor
Displays BCM input data in real time.
Active Test
Operation of electrical loads can be checked by sending driving signal to them.
Revision: 2011 October
2012 JUKE
WCS-20
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
DATA MONITOR
ACTIVE TEST
Display item
[Unit]
Description
PUSH SW
[On/Off]
Status of push-button ignition switch judged by BCM.
UNLK SEN-DR
[On/Off]
Status of unlock sensor judged by BCM.
VEH SPEED 1
[km/h]
Value of vehicle speed signal received from combination meter with CAN communication line.
TAIL LAMP SW
[On/Off]
Status of lighting switch judged by BCM using the combination switch readout function.
FR FOG SW
[On/Off]
Status of front fog lamp switch judged by BCM using the combination switch readout function.
DOOR SW-DR
[On/Off]
Status of driver side door switch judged by BCM.
CDL LOCK SW
[On/Off]
Status of door lock unlock switch judged by BCM.
Display item
[Unit]
Description
SEAT BELT WARN TEST
The seat belt warning chime operation can be checked by operating the relevant function (On/Off).
KEY REMINDER WARN
The key warning chime operation can be checked by operating the relevant function (On/Off).
LIGHT WARN ALM
The light warning chime operation can be checked by operating the relevant function (On/Off).
Revision: 2011 October
2012 JUKE
WCS
DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
WCS-21
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000007836786
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
BUZZER
BUZZER : CONSULT Function (BCM - BUZZER)
INFOID:0000000007577843
CONSULT APPLICATION ITEMS
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp control
INT LAMP
×
×
×
Remote keyless entry system
MULTI REMOTE ENT
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
Air conditioning system
AIR CONDITONER
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
NATS
IMMU
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Back door open
TRUNK
×
Theft warning alarm
THEFT ALM
×
×
×
RAP system
RETAINED PWR
×
×
Signal buffer system
SIGNAL BUFFER
×
×
Panic alarm
PANIC ALARM
×
TPMS
AIR PRESSUE MONITOR
×
×
×
Revision: 2011 October
2012 JUKE
WCS-22
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
DATA MONITOR
ACTIVE TEST
Test item
Diagnosis mode
Description
BUZZER
Data Monitor
Displays BCM input data in real time.
Active Test
Operation of electrical loads can be checked by sending driving signal to them.
Display item
[Unit]
Description
IGN ON SW
[On/Off]
Status of ignition switch judged by BCM.
KEY ON SW
[On/Off]
Status of key switch judged by BCM.
DOOR SW-DR
[km/h]
Status of driver side door switch judged by BCM.
REVERSE SW CAN
[On/Off]
This item is displayed, but cannot be monitored.
TAIL LAMP SW
[On/Off]
Status of lighting switch judged by BCM using the combination switch readout function.
FR FOG SW
[On/Off]
Status of front fog lamp switch judged by BCM using the combination switch readout function.
BUCKLE SW
[On/Off]
Status of seat belt buckle switch (driver side) received from combination meter with CAN communica-
tion line.
VEHICLE SPEED
[km/h]
Value of vehicle speed signal received from combination meter with CAN communication line.
Display item
[Unit]
Description
SEAT BELT WARN TEST
The seat belt warning chime operation can be checked by operating the relevant function (On/Off).
IGN KEY WARN ALM
The key warning chime operation can be checked by operating the relevant function (On/Off).
LIGHT WARN ALM
The light warning chime operation can be checked by operating the relevant function (On/Off).
Revision: 2011 October
2012 JUKE
WCS
COMBINATION METER
WCS-23
< ECU DIAGNOSIS INFORMATION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
ECU DIAGNOSIS INFORMATION
COMBINATION METER
Reference Value
INFOID:0000000007836908
VALUES ON THE DIAGNOSIS TOOL
Monitor Item
Condition
Value/Status
SPEED METER
[km/h]
Ignition switch
ON
While driving
Input value of vehicle speed signal
(CAN communication signal)
NOTE:
655.35 is displayed when the malfunc-
tion signal is received
SPEED OUTPUT
[km/h]
Ignition switch
ON
While driving
Output value of vehicle speed signal
(CAN communication signal)
NOTE:
655.35 is displayed when the malfunc-
tion signal is received
ODO OUTPUT
[km/h or mph]
Ignition switch
ON
—
Output value of odometer signal (CAN
communication signal)
TACHO METER
[rpm]
Ignition switch
ON
Engine running
Input value of engine speed signal
(CAN communication signal)
NOTE:
8191.875 is displayed when the mal-
function signal is received
FUEL METER
[L]
Ignition switch
ON
—
Input value of fuel level sensor signal
W TEMP METER
[
°
C]
Ignition switch
ON
—
Input value of engine coolant tempera-
ture signal (CAN communication sig-
nal)
NOTE:
215 is displayed when the malfunction
signal is input
FUEL CAP W/L
Ignition switch
ON
Fuel filler cap warning display ON
On
Fuel filler cap warning display OFF
Off
ABS W/L
Ignition switch
ON
ABS warning lamp ON
On
ABS warning lamp OFF
Off
VDC/TCS IND
Ignition switch
ON
VDC OFF indicator lamp ON
On
VDC OFF indicator lamp OFF
Off
SLIP IND
Ignition switch
ON
VDC warning lamp ON
On
VDC warning lamp OFF
Off
BRAKE W/L
Ignition switch
ON
Brake warning lamp ON
On
Brake warning lamp OFF
Off
DOOR W/L
Ignition switch
ON
Door open warning lamp ON
On
Door open warning lamp OFF
Off
HI-BEAM IND
Ignition switch
ON
High-beam indicator lamp ON
On
High-beam indicator lamp OFF
Off
TURN IND
Ignition switch
ON
Turn signal indicator lamp ON
On
Turn signal indicator lamp OFF
Off
LIGHT IND
Ignition switch
ON
Tail lamp indicator lamp ON
On
Tail lamp indicator lamp OFF
Off
Revision: 2011 October
2012 JUKE
WCS-24
< ECU DIAGNOSIS INFORMATION >
COMBINATION METER
OIL W/L
Ignition switch
ON
Oil pressure warning lamp ON
On
Oil pressure warning lamp OFF
Off
MIL
Ignition switch
ON
Malfunction indicator lamp ON
On
Malfunction indicator lamp OFF
Off
GLOW IND
Ignition switch
ON
NOTE:
This item is displayed, but cannot be moni-
tored.
Off
C-ENG2 W/L
Ignition switch
ON
NOTE:
This item is displayed, but cannot be moni-
tored.
Off
CRUISE IND
Ignition switch
ON
CRUISE indicator lamp ON
On
CRUISE indicator lamp OFF
Off
SET IND
Ignition switch
ON
NOTE:
This item is displayed, but cannot be moni-
tored.
Off
CVT IND
Ignition switch
ON
CVT indicator ON
On
CVT indicator OFF
Off
4WD W/L
Ignition switch
ON
AWD warning lamp ON
On
AWD warning lamp OFF
Off
4WD LOCK IND
Ignition switch
ON
AWD mode indicator lamp (AWD-V) ON
On
AWD mode indicator lamp (AWD-V) OFF
Off
FUEL W/L
Ignition switch
ON
During low fuel warning indication
On
Other than the above
Off
AIR PRESS W/L
Ignition switch
ON
Low tire pressure warning lamp ON
On
Other than the above
Off
KEY G/Y W/L
Ignition switch
ON
During Intelligent Key system malfunction
indication
On
Other than the above
Off
KEY KNOB W/L
Ignition switch
ON
SHIFT P warning lamp ON
On
SHIFT P warning lamp OFF
Off
EPS W/L
Ignition switch
ON
EPS warning lamp ON
On
EPS warning lamp OFF
Off
DPF W/L
Ignition switch
ON
NOTE:
This item is displayed, but cannot be moni-
tored.
Off
Monitor Item
Condition
Value/Status
Revision: 2011 October
2012 JUKE
WCS
COMBINATION METER
WCS-25
< ECU DIAGNOSIS INFORMATION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
LCD
Ignition switch
LOCK or ACC
Engine start operation indicator lamp ON
(CVT models)
B&P N
Ignition switch
ON
Engine start operation indicator lamp ON
(CVT models)
B&P I
Ignition switch
LOCK or ACC
Engine start operation indicator lamp ON
(M/T models)
C&P N
Ignition switch
ON
Engine start operation indicator lamp ON
(M/T models)
C&P I
Ignition switch
LOCK
During P position warning indication
SFT P
Ignition switch
LOCK
During Intelligent Key low battery warning
indication
BATT
Ignition switch
ON
During take away warning indication
NO KY
Ignition switch
ON
During ACC warning indication
LK WN
SHIFT IND
Ignition switch
ON
Shift position indicator P display
P
Shift position indicator R display
R
Shift position indicator N display
N
Shift position indicator D display
D
Shift position indicator M1 display
M1
Shift position indicator M2 display
M2
Shift position indicator M3 display
M3
Shift position indicator M4 display
M4
Shift position indicator M5 display
M5
Shift position indicator M6 display
M6
O/D OFF SW
Ignition switch
ON
NOTE:
This item is displayed, but cannot be moni-
tored.
Off
M RANGE SW
Ignition switch
ON
Selector lever in manual mode position
On
Other than the above
Off
NM RANGE SW
Ignition switch
ON
Selector lever in manual mode position
Off
Other than the above
On
AT SFT UP SW
Ignition switch
ON
Selector lever in + position
On
Other than the above
Off
AT SFT DWN SW
Ignition switch
ON
Selector lever in – position
On
Other than the above
Off
PKB SW
Ignition switch
ON
Parking brake switch ON
On
Parking brake switch OFF
Off
BUCKLE SW
Ignition switch
ON
Driver seat belt not fastened
On
Driver seat belt fastened
Off
BRAKE SW
Ignition switch
ON
NOTE:
This item is displayed, but cannot be moni-
tored.
Off
BRAKE OIL SW
Ignition switch
ON
Brake fluid level switch ON
On
Brake fluid level switch OFF
Off
Monitor Item
Condition
Value/Status
Revision: 2011 October
2012 JUKE
WCS-26
< ECU DIAGNOSIS INFORMATION >
COMBINATION METER
NOTE:
Some items are not available according to vehicle specification.
TERMINAL LAYOUT
PHYSICAL VALUES
A/C AMP CONN
Ignition switch
ON
Other than the following
On
Receives A/C auto amp. connection recog-
nition signal
Off
PASS BUCKLE SW
Ignition switch
ON
NOTE:
This item is displayed, but cannot be moni-
tored.
Off
DISTANCE
[km]
Ignition switch
ON
—
Distance to empty calculated by com-
bination meter
OUTSIDE TEMP
[
°
C or
°
F]
Ignition switch
ON
—
Input value of ambient sensor signal
(CAN communication signal)
NOTE:
This may not match the indicated value
on the information display.
FUEL LOW SIG
Ignition switch
ON
During low fuel warning indication
On
Other than above
Off
BUZZER
Ignition switch
ON
Buzzer ON
On
Buzzer OFF
Off
ASCD SPD BLNK
Ignition switch
ON
Set vehicle speed indicator blinking
On
Set vehicle speed indicator not blinking
Off
ASCD STATUS
Ignition switch
ON
ASCD and speed limiter system OFF
Off
ASCD system ON
ASCD
ASCD set vehicle speed
CRUISE
ASCD REQ SPD
[km/h or Off]
Ignition switch
ON
While driving
Same value as ASCD or speed limiter
set vehicle speed
TPMS PRESS L
Ignition switch
ON
Low tire pressure warning display ON
On
Low tire pressure warning display OFF
Off
Monitor Item
Condition
Value/Status
JSNIA0623ZZ
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
+
–
Signal name
Input/
Output
1
(L)
—
CAN-H
—
—
—
—
2
(P)
—
CAN-L
—
—
—
—
Revision: 2011 October
2012 JUKE
WCS
COMBINATION METER
WCS-27
< ECU DIAGNOSIS INFORMATION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
4
(Y)
Ground
Vehicle speed signal
(8-pulse)
Output
Ignition
switch
ON
Speedometer operated
[When vehicle speed is ap-
prox. 40 km/h (25 MPH)]
NOTE:
The maximum voltage varies de-
pending on the specification
(destination unit).
6
(BR)
Ground
Fuel level sensor signal
Input
Ignition
switch
ON
—
2WD
AWD
7
(R)
Ground
Air bag signal
Input
Ignition
switch
ON
Air bag warning lamp
ON
4 V
Air bag warning lamp
OFF
0 V
8
*
(Y)
—
—
—
—
—
—
9
(O)
Ground
Seat belt buckle switch sig-
nal (driver side)
Input
Engine
idling
When driver seat belt is fas-
tened.
12 V
When driver seat belt is un-
fastened.
0 V
10
(SB)
Ground
Parking brake switch signal
Input
Ignition
switch
ON
Parking brake applied.
0 V
Parking brake released.
5 V
11
(G)
Ground
Brake fluid level switch sig-
nal
Input
Ignition
switch
ON
Brake fluid level is normal
5 V
Brake fluid level is less than
LOW level
0 V
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
+
–
Signal name
Input/
Output
JSNIA0012GB
JSNIA3305ZZ
JSNIA3721ZZ
Revision: 2011 October
2012 JUKE
WCS-28
< ECU DIAGNOSIS INFORMATION >
COMBINATION METER
13
(B)
Ground
Illumination control signal
Output
Ignition
switch
ON
• Lighting switch 1ST
• When meter illumination
is maximum
• Lighting switch 1ST
• When meter illumination
is step 6
• Lighting switch 1ST
• When meter illumination
is minimum
12 V
14
(V)
Ground
Manual mode shift up sig-
nal
Input
Ignition
switch
ON
Selector lever UP operation
0 V
Other than the above
12 V
15
(L)
Ground
ACC power supply
Input
Ignition
switch
ACC
—
Battery voltage
16
(O)
Ground
Manual mode shift down
signal
Input
Ignition
switch
ON
Selector lever DOWN oper-
ation
0 V
Other than the above
12 V
17
(W)
Ground
Washer level switch signal
Input
Ignition
switch
ON
Low washer fluid warning
lamp ON
0 V
Low washer fluid warning
lamp OFF
12 V
18
(R)
Ground
Security signal
Input
Ignition
switch
ON
Security indicator lamp ON
0 V
Security indicator lamp
OFF
12 V
19
(GR)
Ground
Ambient sensor signal
Input
Ignition
switch
ON
Changes depending to am-
bient temperature.
20
(LG)
Ground
Ambient sensor ground
—
Ignition
switch
ON
—
0 V
21
(B)
Ground
Ground
—
Ignition
switch
ON
—
0 V
22
(B)
Ground
Ground
—
Ignition
switch
ON
—
0 V
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
+
–
Signal name
Input/
Output
JPNIA1687GB
JPNIA1686GB
JSNIA0014GB
Revision: 2011 October 2012 JUKE
WCS
COMBINATION METER
WCS-29
< ECU DIAGNOSIS INFORMATION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
*: This harness is not used.
Fail-Safe
INFOID:0000000007836909
FAIL-SAFE
The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.
23
(B)
Ground
Ground
—
Ignition
switch
ON
—
0 V
24
(L)
Ground
Fuel level sensor ground
—
Ignition
switch
ON
—
0 V
25
(B)
Ground
VDC ground
—
Ignition
switch
ON
—
0 V
27
(LG)
Ground
Battery power supply
Input
Ignition
switch
OFF
—
Battery voltage
28
(GR)
Ground
Ignition signal
Input
Ignition
switch
ON
—
Battery voltage
31
(P)
Ground
A/C auto amp. connection
recognition signal
Input
Ignition
switch
ON
—
5 V
36
(LG)
Ground
Manual mode signal
Input
Ignition
switch
ON
Selector manual mode po-
sition
0 V
Other than the above
12 V
37
(Y)
Ground
Non-manual mode signal
Input
Ignition
switch
ON
Selector manual mode po-
sition
12 V
Other than the above
0 V
38
(P)
Ground
Alternator signal
Input
Ignition
switch
ON
Charge warning lamp ON
2 V
Charge warning lamp OFF
12 V
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
+
–
Signal name
Input/
Output
Function
Specifications
Speedometer
Reset to zero by suspending communication.
Tachometer
Engine coolant temperature gauge
Illumination control
When suspending communication, changes to nighttime mode.
Shift position indicator
When suspending communication, not indicate.
Information display
Instantaneous fuel consumption
• When reception time of an abnormal signal is 2 seconds or
less, the last received datum is used for calculation to indi-
cate the result.
• When reception time of an abnormal signal is more than two
seconds, the last result calculated during normal condition is
indicated.
Average fuel consumption
Possible driving distance
Torque distribution indicator
Low tire pressure warning
The display turns OFF by suspending communication.
Buzzer
The buzzer turns OFF by suspending communication.
Revision: 2011 October
2012 JUKE
WCS-30
< ECU DIAGNOSIS INFORMATION >
COMBINATION METER
DTC Index
INFOID:0000000007836910
Warning lamp/indicator lamp
ABS warning lamp
The lamp turns ON by suspending communication.
Malfunction indicator lamp
VDC OFF indicator lamp
EPS warning lamp
AWD warning lamp
Brake warning lamp
VDC warning lamp
The lamp turns OFF by suspending communication.
High beam indicator lamp
Turn signal indicator lamp
Door warning lamp
Tail lamp indicator lamp
Engine start operation indicator lamp
Shift P warning lamp
Oil pressure warning lamp
CRUISE indicator lamp
AWD mode indicator lamp (AWD)
AWD mode indicator lamp (AWD-V)
Key warning lamp
CVT indicator lamp
Low tire pressure warning lamp
After blinking for 1 minute, the lamp remains ON.
Function
Specifications
Display contents of CONSULT
Diagnostic item is detected when...
Refer to
CAN COMM CIRCUIT
[U1000]
When combination meter is not transmitting or receiving CAN communication signal
for 2 seconds or more.
CONTROL UNIT (CAN)
[U1010]
When detecting error during the initial diagnosis of the CAN controller of combina-
tion meter.
VEHICLE SPEED
[B2205]
The abnormal vehicle speed signal is input from the ABS actuator and electric unit
(control unit) for 2 seconds or more.
ENGINE SPEED
[B2267]
If ECM continuously transmits abnormal engine speed signals for 2 seconds or
more.
WATER TEMP
[B2268]
If ECM continuously transmits abnormal engine coolant temperature signals for 60
seconds or more.
Revision: 2011 October
2012 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст