Nissan Juke (2012 year). Service Repair Manual — part 215
SRC-150
< DTC/CIRCUIT DIAGNOSIS >
B1338, B1340, B1341, B1342 SATELLITE SENSOR RH
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2011 October
2012 JUKE
B1339 SATELLITE SENSOR RH
SRC-151
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1339 SATELLITE SENSOR RH
DTC Logic
INFOID:0000000007578385
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-11, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-151, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007578386
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
REPLACE FRONT DOOR SATELLITE SENSOR
1.
Replace front door satellite sensor RH. Refer to
SR-24, "Removal and Installation"
.
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 2.
NO
>> INSPECTION END
2.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1339
FR-RH DOOR SATEL
SENS
[MIS-INSTALLATION]
Front door satellite sensor RH is out of the
specified specification
Diagnosis sensor unit or front door satellite sen-
sor RH is different from the part specified
Revision: 2011 October
2012 JUKE
SRC-152
< DTC/CIRCUIT DIAGNOSIS >
B1343, B1344 SATELLITE SENSOR LH
B1343, B1344 SATELLITE SENSOR LH
DTC Logic
INFOID:0000000007578387
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-11, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-152, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007578388
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE FRONT DOOR SATELLITE SENSOR
1.
Replace front door satellite sensor LH. Refer to
SR-24, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1343
B1344
FR-LH DOOR SATEL
SENS
[SENSOR MALFUNC-
TION]
Front door satellite sensor LH is malfunc-
tioning
• Harness or connectors
• Malfunction in front door satellite sensor LH
• Malfunction in air bag diagnosis sensor unit
Revision: 2011 October
2012 JUKE
B1343, B1344 SATELLITE SENSOR LH
SRC-153
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2011 October
2012 JUKE
SRC-154
< DTC/CIRCUIT DIAGNOSIS >
B1345, B1347, B1348, B1349 SATELLITE SENSOR LH
B1345, B1347, B1348, B1349 SATELLITE SENSOR LH
DTC Logic
INFOID:0000000007578389
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-11, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-157, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007578390
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE SATELLITE SENSOR
1.
Replace front door satellite sensor LH. Refer to
SR-24, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1345
B1347
B1348
B1349
FR-LH DOOR SATEL
SENS
[COMM MALFUNC-
TION]
Front door satellite sensor LH is malfunc-
tioning
• Harness or connectors
• Malfunction in front door satellite sensor LH
• Malfunction in air bag diagnosis sensor unit
Revision: 2011 October
2012 JUKE
B1345, B1347, B1348, B1349 SATELLITE SENSOR LH
SRC-155
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2011 October
2012 JUKE
SRC-156
< DTC/CIRCUIT DIAGNOSIS >
B1346 SATELLITE SENSOR LH
B1346 SATELLITE SENSOR LH
DTC Logic
INFOID:0000000007578391
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-11, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-156, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007578392
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
REPLACE FRONT DOOR SATELLITE SENSOR
1.
Replace front door satellite sensor LH. Refer to
SR-24, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 2.
NO
>> INSPECTION END
2.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1346
FR-LH DOOR SATEL
SENS
[MIS-INSTALLATION]
Front door satellite sensor LH is out of the
specified specification
Diagnosis sensor unit or front door satellite sen-
sor LH is different from the part specified
Revision: 2011 October
2012 JUKE
B1350, B1351 SATELLITE SENSOR
SRC-157
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1350, B1351 SATELLITE SENSOR
DTC Logic
INFOID:0000000007578393
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-11, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-157, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007578394
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
REPLACE BOTH OF FRONT DOOR SATELLITE SENSOR
1.
Replace both of front door satellite sensor. Refer to
SR-24, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 2.
NO
>> INSPECTION END
2.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1350
B1351
FR DOOR SATEL SENS
Front door satellite sensor is malfunction-
ing or out of the specified specification
• Malfunction in front door satellite sensor LH/RH
• Malfunction in air bag diagnosis sensor unit
Revision: 2011 October
2012 JUKE
SRC-158
< SYMPTOM DIAGNOSIS >
SRS AIR BAG WARNING LAMP DOES NOT TURN OFF
SYMPTOM DIAGNOSIS
SRS AIR BAG WARNING LAMP DOES NOT TURN OFF
Diagnosis Procedure
INFOID:0000000007578395
1.
CHECK AIR BAG MODULE AND SEAT BELT PRE-TENSIONER
Check the deployment of air bag module and seat belt pre-tensioner.
Is air bag module deployed?
YES
>> Replace the malfunctioning parts.
NO
>> GO TO 2.
2.
CHECK AIR BAG FUSE
Check 10 A fuse [No.2, located in fuse block (J/B)].
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace the fuse.
3.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace harness connectors.
4.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace wiring harness.
5.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
2.
Check air bag warning lamp operation.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 6.
6.
REPLACE COMBINATION METER
1.
Replace combination meter. Refer to
MWI-53, "Removal and Installation"
2.
Check air bag warning lamp operation.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 1.
Revision: 2011 October
2012 JUKE
SRS AIR BAG WARNING LAMP DOES NOT TURN ON
SRC-159
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
SRS AIR BAG WARNING LAMP DOES NOT TURN ON
Diagnosis Procedure
INFOID:0000000007578396
1.
CHECK COMBINATION METER POWER SUPPLY AND GROUND CIRCUIT
Check combination meter unit power supply and ground circuit. Refer to
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace harness connectors.
3.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace wiring harness.
4.
CHECK AIR BAG DIAGNOSIS SENSOR UNIT
Disconnect air bag diagnosis sensor unit connector and turn ignition switch ON.
Does air bag warning lamp turn ON?
YES
>> Replace air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
.
NO
>> Replace combination meter. Refer to
MWI-53, "Removal and Installation"
Revision: 2011 October
2012 JUKE
SRC-160
< SYMPTOM DIAGNOSIS >
SRS AIR BAG WARNING LAMP BLINKS
SRS AIR BAG WARNING LAMP BLINKS
Diagnosis Procedure
INFOID:0000000007578397
1.
PERFORM ZERO POINT REST
Perform zero point reset. Refer to
SRC-28, "ZERO POINT RESET : Special Repair Requirement"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace malfunctioning parts.
2.
CHECK BATTERY
Check battery. Refer to
PG-88, "How to Handle Battery"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace malfunctioning parts.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
2.
Check air bag warning lamp operation.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 4.
4.
REPLACE OCCUPANT DETECTION SYSTEM CONTROL UNIT
1.
Replace seat cushion frame. Refer to
SE-18, "Removal and Installation"
2.
Check air bag warning lamp operation.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 1.
Revision: 2011 October
2012 JUKE
ST-1
STEERING
C
D
E
F
H
I
J
K
L
M
SECTION
ST
A
B
ST
N
O
P
CONTENTS
STEERING SYSTEM
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Service Notice or Precautions for Steering System
. ..
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tools . . . . . . . . . . . ....
Commercial Service Tools . . . . . . . . . ....
BASIC INSPECTION . . . . . . . . .
STEERING WHEEL . . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . . ..
SYMPTOM DIAGNOSIS . . . . . . . ...
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . . .
NVH Troubleshooting Chart . . . . . . . . . ..
PERIODIC MAINTENANCE . . . . . . ..
STEERING WHEEL . . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . . ..
REMOVAL AND INSTALLATION . . . .
STEERING WHEEL . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
STEERING COLUMN . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . .
STEERING SHAFT . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
STEERING GEAR AND LINKAGE . . . . ...
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Disassembly and Assembly . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
General Specifications . . . . . . . . . . . .
Steering Wheel . . . . . . . . . . . . . .
Steering Angle . . . . . . . . . . . . . . .
Steering Column . . . . . . . . . . . . . ..
Steering Gear and Linkage . . . . . . . . . ..
Revision: 2012 February
2012 JUKE
ST-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000007577729
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Service Notice or Precautions for Steering System
INFOID:0000000007577730
• In case of removing steering gear assembly, make the final tightening with grounded and unloaded vehicle
condition, and then check wheel alignment.
• Observe the following precautions when disassembling.
- Before disassembly, thoroughly clean the outside of the unit.
- Disassembly should be done in a clean work area. It is important to prevent the internal parts from becoming
contaminated by dirt or other foreign matter.
- For easier and proper assembly, place disassembled parts in order on a parts rack.
- Use nylon cloth or paper towels to clean the parts; common shop rags can leave lint that might interfere with
their operation.
- Never reuse non-reusable parts.
- Before assembling, apply the specified grease to the directed parts.
• During quick steering, rasping noise may be heard from around the steering wheel. This is not a malfunction.
The noise is an operating noise of the EPS system under normal conditions. If the rasping noise occurs dur-
ing slow steering, this may not be an operating noise of the system. In this case, it is necessary to find out
the location of the noise and repair, if necessary.
• Never repeat static steering. (Motor and EPS control unit could be heated.)
Revision: 2012 February
2012 JUKE
PREPARATION
ST-3
< PREPARATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000007577731
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
INFOID:0000000007577732
Tool number
(Kent-Moore No.)
Tool name
Description
ST27180001
(J-25726-A)
Steering wheel puller
Removing steering wheel
ST3127S000
(J-25765-A)
Preload gauge
Measuring steering column rotating torque
KV40107300
(
—
)
Boot band crimping tool
Installing boot clamp (large diameter)
ZZA0819D
ZZA0806D
ZZA1229D
Tool name
Description
Ball joint remover
Removing steering outer socket
Power tool
Loosening bolts and nuts
S-NT146
PBIC0190E
Revision: 2012 February
2012 JUKE
ST-4
< BASIC INSPECTION >
STEERING WHEEL
BASIC INSPECTION
STEERING WHEEL
Inspection
INFOID:0000000007577733
NEUTRAL POSITION STEERING WHEEL
1.
Make sure that steering gear assembly, steering column assembly and steering wheel are installed in the
correct position.
2.
Perform neutral position inspection after wheel alignment. Refer to
3.
Set vehicle to the straight-ahead position and confirm steering wheel is in the neutral position.
4.
Loosen outer socket lock nut and turn inner socket to left and right equally to make fine adjustments if
steering wheel is not in the neutral position.
STEERING WHEEL TURNING FORCE
1.
Park vehicle on a level and dry surface, set parking brake.
2.
Tires need to be inflated normal pressure. Refer to
3.
Start engine.
4.
Check steering wheel turning force when steering wheel has
been turned 360
°
from neutral position.
NOTE:
Multiply the distance from the hook of spring balance to the cen-
ter of steering wheel by the measurement value with a spring
balance.
FRONT WHEEL TURNING ANGLE
1.
Check front wheel turning angle after toe-in inspection. Refer to
2.
Place front wheels on turning radius gauges and rear wheels on
stands, so that vehicle can be level.
3.
Check the maximum inner and outer wheel turning angles for LH
and RH road wheels.
4.
With the engine at idle, turn steering wheel from full left stop to
full right stop and measure the turning angles.
Steering wheel turning
force
: Refer to
.
L
: 185 mm (7.28 in)
JSGIA0027ZZ
FAA0016D
Inner wheel (Angle: A)
: Refer to
.
Outer wheel (Angle: B)
: Refer to
.
SGIA0055E
Revision: 2012 February
2012 JUKE
STEERING WHEEL
ST-5
< BASIC INSPECTION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
5.
Check the following items when turning angle is out of the stan-
dard.
a.
Check rack stroke (L).
b.
If rack stroke is out of specification, replace steering gear
assembly.
• Steering angles are not adjustable. Check steering gear
assembly, steering column assembly, and front suspension
components for wear or damage if any of the turning angles are different from the specified value.
Replace any of them, if any non-standard condition exists.
Rack stroke neutral position (L)
: Refer to
.
JSGIA0272ZZ
Revision: 2012 February
2012 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст