Nissan Juke (2012 year). Service Repair Manual — part 23
FRONT DISC BRAKE
BR-45
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
BRAKE CALIPER ASSEMBLY : Exploded View
INFOID:0000000007579970
REMOVAL
DISASSEMBLY
1.
Brake caliper assembly
: N·m (kg-m, ft-lb)
JPFIA0834GB
1.
Cap
2.
Bleeder valve
3.
Cylinder body
4.
Piston seal
5.
Piston
6.
Piston boot
7.
Sliding pin
8.
Sliding pin boot
9.
Bushing
10.
Torque member
: Apply rubber grease.
: Apply brake fluid.
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
JPFIA0511GB
Revision: 2011 October
2012 JUKE
BR-46
< REMOVAL AND INSTALLATION >
FRONT DISC BRAKE
BRAKE CALIPER ASSEMBLY : Removal and Installation
INFOID:0000000007579971
REMOVAL
WARNING:
Since dust covering the front brake has an affect on human body, the dust must be removed with a
dust collector. Never splatter the dust with an air blow gun.
CAUTION:
• Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it
out immediately and wash with water if it gets on a protect surface. For brake component parts,
never wash them with water.
• Never depress the brake pedal while removing the brake hose. If this is not complied with, brake
fluid may splash.
• Never drop removed parts.
• If the brake fluid or grease adheres to the disc rotor, quickly wipe it off.
1.
Remove tires with power tool.
2.
Fix the disc rotor using wheel nuts.
3.
Drain brake fluid. Refer to
.
4.
Separate brake hose from caliper assembly. Refer to
BR-22, "FRONT : Removal and Installation"
5.
Remove torque member mounting bolts, and remove brake cali-
per assembly.
CAUTION:
Never drop brake pad and caliper assembly.
6.
When removing disc rotor. Refer to
.
INSTALLATION
WARNING:
Since dust covering the front brake has an affect on human body, the dust must be removed with a
dust collector. Never splatter the dust with an air blow gun.
CAUTION:
• Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it
out immediately and wash with water if it gets on a protect surface. For brake component parts,
never wash them with water.
• Never depress the brake pedal while removing the brake hose. If this is not complied with, brake
fluid may splash.
• If the brake fluid or grease adheres to the disc rotor, quickly wipe it off.
1.
Install disc rotor. Refer to
FAX-8, "Removal and Installation"
.
2.
Install the brake caliper assembly to the steering knuckle and
tighten the torque member mounting bolts to the specified
torque.
CAUTION:
Never spill or splash any grease and moisture on the brake
caliper assembly mounting face, threads, mounting bolts
and washers. Wipe out any grease and moisture.
3.
Install brake hose. Refer to
.
4.
Perform the air bleeding. Refer to
5.
Check a drag of front disc brake. If any drag is found, refer to
BR-49, "BRAKE CALIPER ASSEMBLY : Inspection"
6.
Install tires. Refer to
WT-43, "Removal and Installation"
7.
Perform inspection after installation. Refer to
BR-49, "BRAKE CALIPER ASSEMBLY : Inspection"
.
JPFIA0835ZZ
JPFIA0835ZZ
Revision: 2011 October
2012 JUKE
FRONT DISC BRAKE
BR-47
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
BRAKE CALIPER ASSEMBLY : Disassembly and Assembly
INFOID:0000000007579972
DISASSEMBLY
NOTE:
Never remove the torque member, brake pad and pad retainers when disassembling and assembling the cyl-
inder body.
1.
Remove the sliding pin bolt, and remove the cylinder body from the torque member. Refer to
"BRAKE PAD : Removal and Installation"
CAUTION:
Fix the brake pad at suitable tape so that the brake pad will not drop.
2.
Remove sliding pins and sliding pin boots from torque member.
3.
Remove bushing (1) from sliding pin (2).
4.
Place a wooden block as shown in the figure, and blow air from
union bolt mounting hole to remove pistons and piston boots.
CAUTION:
Never get fingers caught in the pistons.
5.
Remove piston seal from cylinder body using seal pick tool.
CAUTION:
Be careful not to damage a cylinder inner wall.
6.
Remove bleeder valve and cap.
7.
Perform inspection after disassembly. Refer to
CALIPER ASSEMBLY : Inspection"
.
ASSEMBLY
1.
Install bleeder valve and cap.
JPFIA0851ZZ
MAA0272D
JPFIA0738ZZ
Revision: 2011 October
2012 JUKE
BR-48
< REMOVAL AND INSTALLATION >
FRONT DISC BRAKE
2.
Apply rubber grease to piston seals (1), and install them to cylin-
der body.
CAUTION:
Never reuse piston seals.
3.
Apply rubber grease to piston boots (1). Cover the piston (2) end
with piston boot, and then install cylinder side lip on piston boot
securely into a groove on cylinder body.
CAUTION:
Never reuse piston boots.
4.
Apply new brake fluid to pistons (1). Push piston into cylinder
body by hand and push piston boot (2) piston-side lip into the
piston groove.
CAUTION:
Press the pistons evenly and vary the pressing point to pre-
vent cylinder inner wall from being rubbed.
5.
Apply rubber grease to mating faces (A) between sliding pin (1)
and bushing (2), and install bushing to sliding pin.
JPFIA0039ZZ
JPFIA0739ZZ
JPFIA0034ZZ
JPFIA0836ZZ
Revision: 2011 October
2012 JUKE
FRONT DISC BRAKE
BR-49
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
6.
Apply rubber grease to mating faces (A) between sliding pin (1)
and sliding pin boot (2), and install sliding pin and sliding pin
boot to sliding torque member (3).
7.
Install the cylinder body to tighten cylinder body mounting bolts
to the specified torque. Refer to
.
BRAKE CALIPER ASSEMBLY : Inspection
INFOID:0000000007579973
INSPECTION AFTER DISASSEMBLY
Check the following items and replace if necessary.
Cylinder Body
Check the inner wall of the cylinder for rust, wear, cracks or damage.
CAUTION:
Always clean with new brake fluid. Never clean with mineral oil such as gasoline and light oil.
Torque Member
Check the torque member for rust, wear, cracks or damage.
Pistons
Check the surface of the piston for rust, wear, cracks or damage.
CAUTION:
A piston sliding surface is plated. Never polish with sandpaper.
Sliding Pin, Sliding Pin Boot and Bushing
Check the sliding pins, sliding boots and bushing for rust, wear, cracks or damage.
INSPECTION AFTER INSTALLATION
1.
Check a drag of front disc brake. If any drag is found, follow the procedure described below.
2.
Remove brake pads. Refer to
BR-42, "BRAKE PAD : Removal and Installation"
.
3.
Press the pistons. Refer to
BR-42, "BRAKE PAD : Removal and Installation"
.
4.
Install brake pads. Refer to
BR-42, "BRAKE PAD : Removal and Installation"
.
5.
Securely depress the brake pedal several times.
6.
Check a drag of front disc brake again. If any drag is found, disassemble the cylinder body and replace if
necessary. Refer to
BR-47, "BRAKE CALIPER ASSEMBLY : Disassembly and Assembly"
.
7.
Burnish contact surface between disc rotor and brake pads after refinishing or replacing disc rotor, or if a
soft pedal occurs at very low mileage. Refer to
BR-14, "DISC ROTOR : Inspection and Adjustment"
JPFIA0837ZZ
Revision: 2011 October
2012 JUKE
BR-50
< REMOVAL AND INSTALLATION >
REAR DISC BRAKE
REAR DISC BRAKE
BRAKE PAD
BRAKE PAD : Exploded View
INFOID:0000000007579974
BRAKE PAD : Removal and Installation
INFOID:0000000007579975
REMOVAL
WARNING:
Since dust covering the rear brake has an affect on human body, the dust must be removed with a
dust collector. Never splatter the dust with an air blow gun.
CAUTION:
• Never depress the brake pedal while removing the brake pads because the piston may pop out.
• If the brake fluid or grease adheres to the disc rotor, quickly wipe it off.
1.
Remove tires with power tool.
2.
Remove lower sliding pin bolt.
1.
Sliding pin bolt
2.
Cylinder body
3.
Inner shim cover
4.
Inner shim
5.
Inner pad (with pad wear sensor)
6.
Pad retainer
7.
Torque member
8.
Outer pad
9.
Outer shim
10.
Outer shim cover
1 Apply rubber grease.
2: Apply MOLYKOTE
®
AS880N or silicone-based grease.
: N·m (kg-m, ft-lb)
JSFIA0490GB
JSFIA0491ZZ
Revision: 2011 October
2012 JUKE
REAR DISC BRAKE
BR-51
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
3.
Suspend the cylinder body with suitable wire so that the brake
hose will not stretch.
4.
Remove the brake pads, shims, shim covers and pad retainers from the torque member.
CAUTION:
• Never deform the pad retainer (2) when removing the pad
retainer from the torque member (1).
• Never damage the piston boot.
• Never drop the brake pads, shims, and the shim covers.
• Remember each position of the removed brake pads.
5.
Perform inspection after removal. Refer to
INSTALLATION
WARNING:
Since dust covering the rear brake has an affect on human body, the dust must be removed with a
dust collector. Never splatter the dust with an air blow gun.
CAUTION:
• Never depress the brake pedal while removing the brake pads or the cylinder body because the pis-
ton may pop out.
• If the brake fluid or grease adheres to the disc rotor, quickly wipe it off.
1.
Install the pad retainers (1) to the torque member (2) if the pad
retainers has been removed.
CAUTION:
• Securely assemble the pad retainers so that it will not be
lifted up from the torque member.
• Never deform the pad retainers.
2.
Apply MOLYKOTE
®
AS880N or silicone-based grease to the
mating faces (A) between the brake pads and the shims, and
install the shims to the brake pad.
CAUTION:
Always replace the shim together with the shim cover when
replacing the brake pad.
3.
Install the brake pads to the torque member.
4.
Install cylinder body to torque member.
CAUTION:
• Never damage the piston boot.
JSFIA0492ZZ
JPFIA0118ZZ
PFIA0763J
JSFIA0493ZZ
Revision: 2011 October
2012 JUKE
BR-52
< REMOVAL AND INSTALLATION >
REAR DISC BRAKE
• When replacing brake pad with new one, check a brake fluid level in the reservoir tank because
brake fluid returns to master cylinder reservoir tank when pressing piston in.
NOTE:
Use a disc brake piston tool to easily press piston.
5.
Install the lower sliding pin bolt and tighten it to the specified
torque.
6.
Depress the brake pedal several times to check that no drag feel
is present for the rear disc brake. Refer to
7.
Install tires. Refer to
WT-43, "Removal and Installation"
BRAKE PAD : Inspection
INFOID:0000000007579976
INSPECTION AFTER REMOVAL
• Replace the shims and the shim covers if rust is excessively attached.
• Eliminate rust on the pad retainers and the torque member. Replace them if rust is excessively attached.
INSPECTION AFTER INSTALLATION
1.
Check a drag of rear disc brake. If any drag is found, follow the procedure described below.
2.
Remove brake pads. Refer to
BR-50, "BRAKE PAD : Removal and Installation"
.
3.
Press the pistons. Refer to
BR-50, "BRAKE PAD : Removal and Installation"
.
4.
Install brake pads. Refer to
BR-50, "BRAKE PAD : Removal and Installation"
.
5.
Securely depress the brake pedal several times.
6.
Check a drag of rear disc brake again. If any drag is found, disassemble the cylinder body and replace if
necessary. Refer to
BR-54, "BRAKE CALIPER ASSEMBLY : Disassembly and Assembly"
7.
Burnish contact surfaces brake pads and disc rotor after refinishing or replacing brake pads, or if a soft
pedal occurs at very low mileage. Refer to
BR-16, "BRAKE PAD : Inspection and Adjustment"
BRAKE CALIPER ASSEMBLY
BRAKE CALIPER ASSEMBLY : Exploded View
INFOID:0000000007579977
REMOVAL
JSFIA0491ZZ
JPFIA0677GB
Revision: 2011 October
2012 JUKE
REAR DISC BRAKE
BR-53
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
DISASSEMBLY
BRAKE CALIPER ASSEMBLY : Removal and Installation
INFOID:0000000007579978
REMOVAL
WARNING:
Since dust covering the rear brake has an affect on human body, the dust must be removed with a
dust collector. Never splatter the dust with an air blow gun.
CAUTION:
• Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it
out immediately and wash with water if it gets on a protect surface. For brake component parts,
never wash them with water.
• Never depress the brake pedal while removing the brake hose. If this is not complied with, brake
fluid may splash.
• Never drop removed parts.
• If the brake fluid or grease adheres to the disc rotor, quickly wipe it off.
1.
Remove tires with power tool.
2.
Fix the disc rotor using wheel nuts.
3.
Drain brake fluid. Refer to
4.
Separate brake hose from caliper assembly. Refer to
BR-27, "REAR : Removal and Installation"
.
1.
Brake caliper assembly
: N·m (kg-m, ft-lb)
1.
Sliding pin bolt
2.
Bushing
3.
Cap
4.
Bleeder valve
5.
Cylinder body
6.
Piston seal
7.
Piston
8.
Piston boot
9.
Sliding pin boot
10.
Torque member
: Apply rubber grease.
: Apply brake fluid.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
JSFIA0494GB
Revision: 2011 October
2012 JUKE
BR-54
< REMOVAL AND INSTALLATION >
REAR DISC BRAKE
5.
Remove torque member mounting bolts, and remove brake cali-
per assembly.
CAUTION:
Never drop brake pad and caliper assembly.
6.
When removing disc rotor.
• 2WD: Refer to
RAX-5, "Removal and Installation"
.
• AWD: Refer to
RAX-14, "Removal and Installation"
.
INSTALLATION
WARNING:
Since dust covering the rear brake has an affect on human body, the dust must be removed with a
dust collector. Never splatter the dust with an air blow gun.
CAUTION:
• Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it
out immediately and wash with water if it gets on a protect surface. For brake component parts,
never wash them with water.
• Never depress the brake pedal while removing the brake hose. If this is not complied with, brake
fluid may splash.
• If the brake fluid or grease adheres to the disc rotor, quickly wipe it off.
1.
Install disc rotor.
• 2WD: Refer to
RAX-5, "Removal and Installation"
.
• AWD: Refer to
RAX-14, "Removal and Installation"
.
2.
Install the brake caliper assembly to the axle housing and
tighten the torque member mounting bolts to the specified
torque.
CAUTION:
Never spill or splash any grease and moisture on the brake
caliper assembly mounting face, threads, mounting bolts
and washers. Wipe out any grease and moisture.
3.
Install brake hose. Refer to
BR-27, "REAR : Removal and Instal-
.
4.
Perform the air bleeding. Refer to
5.
Check a drag of rear disc brake. If any drag is found, refer to
BR-52, "BRAKE PAD : Inspection"
6.
Install tires. Refer to
WT-43, "Removal and Installation"
7.
Perform inspection after installation. Refer to
BR-56, "BRAKE CALIPER ASSEMBLY : Inspection"
.
BRAKE CALIPER ASSEMBLY : Disassembly and Assembly
INFOID:0000000007579979
DISASSEMBLY
NOTE:
Never remove the torque member, brake pad and pad retainers when disassembling and assembling the cyl-
inder body.
1.
Remove the sliding pin bolt, and remove the cylinder body from the torque member. Refer to
"BRAKE PAD : Removal and Installation"
CAUTION:
Fix the brake pad at suitable tape so that the brake pad will not drop.
2.
Remove sliding pin boots from torque member.
JSFIA0495ZZ
JSFIA0495ZZ
Revision: 2011 October
2012 JUKE
REAR DISC BRAKE
BR-55
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
3.
Remove bushing (1) from sliding pin bolt (2).
4.
Place a wooden block as shown in the figure, and blow air from
union bolt mounting hole to remove pistons and piston boots.
CAUTION:
Never get fingers caught in the pistons.
5.
Remove piston seal from cylinder body using seal pick tool.
CAUTION:
Be careful not to damage a cylinder inner wall.
6.
Remove bleeder valve and cap.
7.
Perform inspection after disassembly. Refer to
CALIPER ASSEMBLY : Inspection"
.
ASSEMBLY
1.
Install bleeder valve and cap.
2.
Apply rubber grease to piston seals (1), and install them to cylin-
der body.
CAUTION:
Never reuse piston seals.
JSFIA0496ZZ
MAA0272D
JPFIA0738ZZ
JPFIA0039ZZ
Revision: 2011 October
2012 JUKE
BR-56
< REMOVAL AND INSTALLATION >
REAR DISC BRAKE
3.
Apply rubber grease to piston boots (1). Cover the piston (2) end
with piston boot, and then install cylinder side lip on piston boot
securely into a groove on cylinder body.
CAUTION:
Never reuse piston boots.
4.
Apply new brake fluid to pistons (1). Push piston into cylinder
body by hand and push piston boot (2) piston-side lip into the
piston groove.
CAUTION:
Press the pistons evenly and vary the pressing point to pre-
vent cylinder inner wall from being rubbed.
5.
Apply rubber grease to mating faces (A) between sliding pin bolt
(1) and bushing (2), and install bushing to sliding pin.
6.
Apply rubber grease to mating faces (A) between sliding pin bolt
(1) and sliding pin boot (2), and install sliding pin and sliding pin
boot to sliding torque member.
7.
Install the cylinder body to tighten sliding pin bolts to the speci-
fied torque. Refer to
BR-50, "BRAKE PAD : Exploded View"
BRAKE CALIPER ASSEMBLY : Inspection
INFOID:0000000007579980
INSPECTION AFTER DISASSEMBLY
Check the following items and replace if necessary.
Cylinder Body
Check the inner wall of the cylinder for rust, wear, cracks or damage.
CAUTION:
Always clean with new brake fluid. Never clean with mineral oil such as gasoline and light oil.
Torque Member
Check the torque member for rust, wear, cracks or damage.
JPFIA0739ZZ
JPFIA0034ZZ
JSFIA0497ZZ
JSFIA0498ZZ
Revision: 2011 October
2012 JUKE
REAR DISC BRAKE
BR-57
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
Pistons
Check the surface of the piston for rust, wear, cracks or damage.
CAUTION:
A piston sliding surface is plated. Never polish with sandpaper.
Sliding Pin, Sliding Pin Boot and Bushing
Check the sliding pins, sliding boots and bushing for rust, wear, cracks or damage.
INSPECTION AFTER INSTALLATION
1.
Check a drag of rear disc brake. If any drag is found, follow the procedure described below.
2.
Remove brake pads. Refer to
BR-50, "BRAKE PAD : Removal and Installation"
.
3.
Press the pistons. Refer to
BR-50, "BRAKE PAD : Removal and Installation"
.
4.
Install brake pads. Refer to
BR-50, "BRAKE PAD : Removal and Installation"
.
5.
Securely depress the brake pedal several times.
6.
Check a drag of rear disc brake again. If any drag is found, disassemble the cylinder body and replace if
necessary. Refer to
BR-54, "BRAKE CALIPER ASSEMBLY : Disassembly and Assembly"
.
7.
Burnish contact surface between disc rotor and brake pads after refinishing or replacing disc rotor, or if a
soft pedal occurs at very low mileage. Refer to
BR-16, "DISC ROTOR : Inspection and Adjustment"
Revision: 2011 October
2012 JUKE
BR-58
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specifications
INFOID:0000000007579981
Unit: mm (in)
Brake Pedal
INFOID:0000000007579982
Unit: mm (in)
Brake Booster
INFOID:0000000007579983
Unit: mm (in)
Front Disc Brake
INFOID:0000000007579984
Unit: mm (in)
Rear Disc Brake
INFOID:0000000007579985
Unit: mm (in)
Front brake
Cylinder bore diameter
57.2 (2.252)
Pad length
×
width
×
thickness
126.0
×
46.0
×
11.0 (4.96
×
1.811
×
0.433)
Rotor outer diameter
×
thickness
296
×
26.0 (11.65
×
1.024)
Rear brake
Cylinder bore diameter
34.93 (1.3752)
Pad length
×
width
×
thickness
83.0
×
31.9
×
8.5 (3.268
×
1.256
×
0.335)
Rotor outer diameter
×
thickness
292
×
9.0 (11.50
×
0.354)
Master cylinder
Cylinder bore diameter
23.8 (15/16)
Control valve
Valve type
Electric brake force distribution
Brake booster
Diaphragm diameter
256 (10)
Recommended brake fluid
Refer to
MA-10, "Fluids and Lubricants"
Item
Standard
Brake pedal height
160.4 – 170.4 (6.31 – 6.71)
Depressed brake pedal height
[Depressing 490 N (50 kg, 110 lb) while turning the engine ON]
70.0 (2.756) or more
Clearance between stop lamp switch and brake pedal position switch threaded end and the
brake pedal lever
0.74 – 1.96 (0.0291 – 0.0772)
Brake pedal play
3 – 11 (0.12 – 0.43)
Item
Standard
Input rod length
156.5 – 157.5 (6.16 – 6.20)
Item
Limit
Brake pad
Wear thickness
2.0 (0.079)
Disc rotor
Wear thickness
24.0 (0.945)
Thickness variation (measured at 8 positions)
0.008 (0.0003)
Runout (with it attached to the vehicle)
0.035 (0.0014)
Item
Limit
Brake pad
Wear thickness
2.0 (0.079)
Disc rotor
Wear thickness
8.0 (0.315)
Thickness variation (measured at 8 positions)
0.016 (0.0006)
Runout (with it attached to the vehicle)
0.1 (0.004)
Revision: 2011 October
2012 JUKE
BRC-1
BRAKES
C
D
E
G
H
I
J
K
L
M
SECTION
BRC
A
B
BRC
N
O
P
CONTENTS
BRAKE CONTROL SYSTEM
WITH VDC
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Procedure without Cowl Top Cover
. ..
Precaution for Brake System . . . . . . . . ....
Precaution for Brake Control system . . . . . ....
Precaution for Harness Repair . . . . . . . . ..
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Commercial Service Tool . . . . . . . . . . ..
SYSTEM DESCRIPTION . . . . . . . ..
COMPONENT PARTS . . . . . . . . . .
Component Parts Location . . . . . . . . . ....
Component Description . . . . . . . . . . ...
Wheel Sensor and Sensor Rotor . . . . . . .
ABS Actuator and Electric Unit (Control Unit) . . .
Stop Lamp Switch . . . . . . . . . . . . ...
Brake Pedal Position Switch . . . . . . . . ...
Steering Angle Sensor . . . . . . . . . . .
Yaw Rate/Side/Decel G Sensor . . . . . . . ..
VDC OFF Switch . . . . . . . . . . . . . .
Brake Fluid Level Switch . . . . . . . . . . .
Parking Brake Switch . . . . . . . . . . . ..
SYSTEM . . . . . . . . . . . . . . . .
System Description . . . . . . . . . . . . .
Fail-safe . . . . . . . . . . . . . . . . ..
VDC FUNCTION . . . . . . . . . . . . . .
VDC FUNCTION : System Description . . . . ...
TCS FUNCTION . . . . . . . . . . . . . .
TCS FUNCTION : System Description . . . . ...
ABS FUNCTION . . . . . . . . . . . . . .
ABS FUNCTION : System Description . . . . .
EBD FUNCTION . . . . . . . . . . . . . .
EBD FUNCTION : System Description . . . . .
BRAKE LIMITED SLIP DIFFERENTIAL (BLSD)
FUNCTION . . . . . . . . . . . . . . . . .
BRAKE LIMITED SLIP DIFFERENTIAL (BLSD)
FUNCTION : System Description . . . . . . .
DIAGNOSIS SYSTEM [ABS ACTUATOR
AND ELECTRIC UNIT (CONTROL UNIT)] . ...
CONSULT Function . . . . . . . . . . . . .
ECU DIAGNOSIS INFORMATION . . . ..
ABS ACTUATOR AND ELECTRIC UNIT
(CONTROL UNIT) . . . . . . . . . . . .
Reference Value . . . . . . . . . . . . . ..
Fail-safe . . . . . . . . . . . . . . . . ...
DTC Inspection Priority Chart . . . . . . . . ..
DTC Index . . . . . . . . . . . . . . . ...
WIRING DIAGRAM . . . . . . . . . ..
BRAKE CONTROL SYSTEM . . . . . . ...
Wiring Diagram . . . . . . . . . . . . . .
BASIC INSPECTION . . . . . . . . ...
DIAGNOSIS AND REPAIR WORK FLOW . ...
Work Flow . . . . . . . . . . . . . . . .
Diagnostic Work Sheet . . . . . . . . . . .
Description . . . . . . . . . . . . . . . ...
ADJUSTMENT OF STEERING ANGLE SEN-
SOR NEUTRAL POSITION . . . . . . . ...
Description . . . . . . . . . . . . . . . ...
Revision: 2011 October
2012 JUKE
BRC-2
Work Procedure . . . . . . . . . . . . . ..
DTC/CIRCUIT DIAGNOSIS . . . . . . .
C1101, C1102, C1103, C1104 WHEEL SEN-
SOR . . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
C1105, C1106, C1107, C1108 WHEEL SEN-
SOR . . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
C1109 POWER AND GROUND SYSTEM . . .
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
C1110, C1170 ABS ACTUATOR AND ELEC-
TRIC UNIT (CONTROL UNIT) . . . . . . ...
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
C1111 ABS MOTOR, MOTOR RELAY SYS-
TEM . . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
C1113, C1145, C1146 YAW RATE/SIDE/DE-
CEL G SENSOR . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
C1115 WHEEL SENSOR . . . . . . . . ...
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
C1116 STOP LAMP SWITCH . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
Component Inspection . . . . . . . . . . ....
C1120, C1122, C1124, C1126 ABS IN VALVE
SYSTEM . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
C1121, C1123, C1125, C1127 ABS OUT
VALVE SYSTEM . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
C1130 ENGINE SIGNAL . . . . . . . . ...
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
C1140 ACTUATOR RELAY SYSTEM . . . ...
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
C1143 STEERING ANGLE SENSOR . . . .
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
C1144 INCOMPLETE STEERING ANGLE
SENSOR ADJUSTMENT . . . . . . . . ..
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
C1155 BRAKE FLUID LEVEL SWITCH . . ...
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
Component Inspection . . . . . . . . . . .
C1164, C1165 CV SYSTEM . . . . . . . ..
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
C1166, C1167 SV SYSTEM . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
C1176 STOP LAMP SW2 . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ..
U1000 CAN COMM CIRCUIT . . . . . . ...
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
U1010 CONTROL UNIT (CAN) . . . . . .
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
POWER SUPPLY AND GROUND CIRCUIT .
Diagnosis Procedure . . . . . . . . . . . .
PARKING BRAKE SWITCH . . . . . . . .
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ..
VDC OFF SWITCH . . . . . . . . . . ...
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ..
ABS WARNING LAMP . . . . . . . . . .
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
BRAKE WARNING LAMP . . . . . . . .
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
VDC WARNING LAMP . . . . . . . . . .
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
VDC OFF INDICATOR LAMP . . . . . . ..
Component Function Check . . . . . . . . .
Revision: 2011 October
2012 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст