Nissan Juke (2012 year). Service Repair Manual — part 42
CO-24
< REMOVAL AND INSTALLATION >
[MR16DDT ]
WATER OUTLET
3.
Remove battery.
.
4.
Remove air duct (upper) and air cleaner cover assembly and air cleaner body assembly.
5.
Disconnect radiator hose (upper). Refer to
.
6.
Remove water outlet adaptor.
7.
Disconnect connectors of engine harness around the battery.
8.
Remove bracket (2), and disconnect engine harness clip. (trans-
mission side and water outlet side)
9.
Disconnect crankshaft position sensor harness connector.
10. Move engine harness, and keep a service area.
11. Remove water hose of each water outlet connection and heater hose.
12. Remove water outlet.
13. Remove engine coolant temperature sensor from water outlet, if necessary.
INSTALLATION
Note the following, and install in the reverse order of removal.
Water Control valve
• Install water control valve with making rubber ring (1) groove fit to
water control valve flange (A) with the whole circumference.
• Install water control valve (2) with the arrow (A) facing up and the
frame center part (B) facing upwards.
Inspection
INFOID:0000000007580012
INSPECTION AFTER REMOVAL
Water Control Valve
1
: Engine harness
JPBIA4454ZZ
JPBIA4458ZZ
1
: Water outlet
JPBIA4373ZZ
Revision: 2011 October
2012 JUKE
WATER OUTLET
CO-25
< REMOVAL AND INSTALLATION >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
CO
N
P
O
• Place a thread (A) so that it is caught in the valves of water control
valve (1). Immerse fully in a container (B) filled with water. Heat
while stirring.
• The valve opening temperature is the temperature at which the
valve opens and falls from the thread.
• Continue heating. Check the continuous valve lifting toward maxi-
mum valve lift.
NOTE:
The maximum valve lift amount standard temperature for water
control valve is the reference value.
• After checking the maximum valve lift amount, lower the water
temperature and check the valve closing temperature.
• If out of the standard, replace water control valve.
INSPECTION AFTER INSTALLATION
• Check for leakage of engine coolant using the radiator cap tester adapter (commercial service tool) and the
radiator cap tester (commercial service tool). Refer to
.
• Start and warm up the engine. Check visually that there is no leakage of engine coolant.
Standard:
Refer to
.
PBIC3314J
Revision: 2011 October
2012 JUKE
CO-26
< SERVICE DATA AND SPECIFICATIONS (SDS)
[MR16DDT ]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Periodical Maintenance Specification
INFOID:0000000007580013
ENGINE COOLANT CAPACITY (APPROXIMATE)
Unit:
(US qt, Imp qt)
Radiator
INFOID:0000000007580014
Unit: kPa (kg/cm
2
, psi)
Thermostat
INFOID:0000000007580015
Standard
Water Control Valve
INFOID:0000000007580016
Standard
Engine coolant capacity (With reservoir tank at “MAX” level)
M/T models
7.9 (8- 3/8, 7)
CVT models
8.1 (8- 1/2, 7-1/8)
Reservoir tank engine coolant capacity (At “MAX” level)
0.6 (5/8, 1/2)
Cap relief pressure
Standard
78 - 98 (0.8 - 1.0, 11 - 14)
Limit
59 (0.6, 9)
Leakage testing pressure
98 (1.0, 14)
Valve opening temperature
80.5 - 83.5
°
C (177 - 182
°
F)
Maximum valve lift
8.0 mm/95
°
C (0.315 in/203
°
F)
Valve closing temperature
77
°
C (171
°
F)
Valve opening temperature
93.5 - 96.5
°
C (200 - 206
°
F)
Maximum valve lift
8.0 mm/108
°
C (0.315 in/226
°
F)
Valve closing temperature
90
°
C (194
°
F)
Revision: 2011 October
2012 JUKE
DEF-1
DRIVER CONTROLS
C
D
E
F
G
H
I
J
K
M
SECTION
DEF
A
B
DEF
N
O
P
CONTENTS
DEFOGGER
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
SYSTEM DESCRIPTION . . . . . . . ..
COMPONENT PARTS . . . . . . . . . .
Component Parts Location . . . . . . . . . ....
Component Description . . . . . . . . . . .....
SYSTEM . . . . . . . . . . . . . . . ..
WITH AUTO A/C . . . . . . . . . . . . . . ..
WITH AUTO A/C : System Diagram . . . . . .....
WITH AUTO A/C : System Description . . . . .....
WITHOUT AUTO A/C . . . . . . . . . . . . ..
WITHOUT AUTO A/C : System Diagram . . . . ..
WITHOUT AUTO A/C : System Description . . .....
DIAGNOSIS SYSTEM (BCM) (WITH INTELLI-
GENT KEY SYSTEM) . . . . . . . . . . ..
COMMON ITEM . . . . . . . . . . . . . . ...
COMMON ITEM : CONSULT Function (BCM -
COMMON ITEM) . . . . . . . . . . . . . ...
REAR WINDOW DEFOGGER . . . . . . . . .....
REAR WINDOW DEFOGGER : CONSULT Func-
tion (BCM - REAR DEFOGGER) . . . . . . . ..
DIAGNOSIS SYSTEM (BCM) (WITHOUT IN-
TELLIGENT KEY SYSTEM) . . . . . . . ...
COMMON ITEM . . . . . . . . . . . . . . .
COMMON ITEM : CONSULT Function (BCM -
COMMON ITEM) . . . . . . . . . . . . . .
REAR WINDOW DEFOGGER . . . . . . . . ...
REAR WINDOW DEFOGGER : CONSULT Func-
tion (BCM - REAR DEFOGGER) . . . . . . . .
DIAGNOSIS SYSTEM (IPDM E/R) . . . . ...
WITH INTELLIGENT KEY . . . . . . . . . . .
WITH INTELLIGENT KEY : Diagnosis Description
.
WITH INTELLIGENT KEY : CONSULT Function
(IPDM E/R) . . . . . . . . . . . . . . . ..
WITHOUT INTELLIGENT KEY . . . . . . . . ..
WITHOUT INTELLIGENT KEY : Diagnosis De-
scription . . . . . . . . . . . . . . . . ...
WITHOUT INTELLIGENT KEY : CONSULT Func-
tion (IPDM E/R) . . . . . . . . . . . . . ...
ECU DIAGNOSIS INFORMATION . . . ..
BCM, IPDM E/R . . . . . . . . . . . . .
List of ECU Reference . . . . . . . . . . . .
BASIC INSPECTION . . . . . . . . ...
DIAGNOSIS AND REPAIR WORK FLOW . ...
Work Flow . . . . . . . . . . . . . . . .
DTC/CIRCUIT DIAGNOSIS . . . . . . .
REAR WINDOW DEFOGGER SWITCH . . ...
WITH AUTO A/C . . . . . . . . . . . . . .
WITH AUTO A/C : Description . . . . . . . .
WITH AUTO A/C : Component Function Check . ..
WITH AUTO A/C : Diagnosis Procedure . . . . .
WITHOUT AUTO A/C . . . . . . . . . . . .
WITHOUT AUTO A/C : Description . . . . . . .
WITHOUT AUTO A/C : Component Function
Check . . . . . . . . . . . . . . . . . ..
WITHOUT AUTO A/C : Diagnosis Procedure . . .
WITHOUT AUTO A/C : Component Inspection . ...
Revision: 2011 October
2012 JUKE
DEF-2
REAR WINDOW DEFOGGER RELAY . . . ..
Description . . . . . . . . . . . . . . . ..
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
REAR WINDOW DEFOGGER . . . . . . ...
Description . . . . . . . . . . . . . . . ..
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
Component Inspection . . . . . . . . . . ....
DOOR MIRROR DEFOGGER . . . . . . ...
Description . . . . . . . . . . . . . . . ..
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
DRIVER SIDE DOOR MIRROR DEFOGGER ...
Description . . . . . . . . . . . . . . . ..
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
PASSENGER SIDE DOOR MIRROR DEFOG-
GER . . . . . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . . ..
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
REAR WINDOW DEFOGGER FEEDBACK
SIGNAL . . . . . . . . . . . . . . . ..
Description . . . . . . . . . . . . . . . ..
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
REAR WINDOW DEFOGGER SYSTEM . . ...
Wiring Diagram - DEFOGGER CONTROL SYS-
TEM - . . . . . . . . . . . . . . . . . ..
SYMPTOM DIAGNOSIS . . . . . . . .
ALL DEFOGGER SYSTEMS DO NOT OPER-
ATE . . . . . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
REAR WINDOW DEFOGGER DOES NOT
OPERATE BUT BOTH DOOR MIRROR DE-
FOGGERS OPERATE . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
DOOR MIRROR DEFOGGER DOES NOT OP-
ERATE . . . . . . . . . . . . . . . ...
BOTH SIDES . . . . . . . . . . . . . . . .
BOTH SIDES : Description . . . . . . . . . .
BOTH SIDES : Diagnosis Procedure . . . . . ..
DRIVER SIDE . . . . . . . . . . . . . . .
DRIVER SIDE : Description . . . . . . . . .
DRIVER SIDE : Diagnosis Procedure . . . . . .
PASSENGER SIDE . . . . . . . . . . . . ...
PASSENGER SIDE : Description . . . . . . ...
PASSENGER SIDE : Diagnosis Procedure . . .
Diagnosis Procedure . . . . . . . . . . . ...
REAR WINDOW DEFOGGER INDICATOR
DOES NOT ILLUMINATE . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
REMOVAL AND INSTALLATION . . . ..
FILAMENT . . . . . . . . . . . . . . .
Inspection and Repair . . . . . . . . . . . .
CONDENSER . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Revision: 2011 October
2012 JUKE
PRECAUTIONS
DEF-3
< PRECAUTION >
C
D
E
F
G
H
I
J
K
M
A
B
DEF
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000007579478
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Revision: 2011 October
2012 JUKE
DEF-4
< SYSTEM DESCRIPTION >
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location
INFOID:0000000007579480
*
1
:With automatic A/C
*
2
:With manual A/C
*
3
:For models with door mirror defogger
Component Description
INFOID:0000000007579481
1.
SYSTEM : Component Parts Loca-
tion"
2.
Rear window defogger connector
3.
Rear window defogger connector
4.
Multidisplay unit*
1
A/C control*
2
(Rear window defogger switch)
5.
Door mirror defogger*
3
6.
7.
Condenser
JMLIA1473ZZ
BCM
• Transmits rear window defogger control signal to IPDM E/R via CAN communi-
cation
• Performs the timer control of rear window defogger
IPDM E/R
• Rear window defogger relay is installed.
• Receives rear window defogger control signal from BCM via CAN communica-
tion.
• Controls rear window defogger relay.
• Multidisplay unit*
1
• A/C control*
2
• The rear window defogger switch is installed
• Turns the indicator lamp ON when detecting the operation of rear window defog-
ger
Rear window defogger switch
• Rear window defogger and door mirror defogger*
3
are operated by turning the
rear window defogger switch ON.
• The indicator lamp in the rear window defogger illuminates when the rear win-
dow defogger is operating.
Rear window defogger relay
Operates rear window defogger and door mirror defogger*
3
with IPDM E/R control.
Rear window defogger
Heats the heating wire with the power supply from the rear window defogger relay
to prevent the rear window from fogging up.
Door mirror defogger*
3
Heats the heating wire with the power supply from the rear window defogger relay
to prevent the door mirror from fogging up.
Revision: 2011 October
2012 JUKE
COMPONENT PARTS
DEF-5
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
DEF
N
O
P
*
1
:With automatic A/C
*
2
:With manual A/C
*
3
:For models with door mirror defogger
Revision: 2011 October
2012 JUKE
DEF-6
< SYSTEM DESCRIPTION >
SYSTEM
SYSTEM
WITH AUTO A/C
WITH AUTO A/C : System Diagram
INFOID:0000000007579482
WITH AUTO A/C : System Description
INFOID:0000000007579483
OPERATION DESCRIPTION
• BCM detects that the rear window defogger switch turns ON while ignition switch is ON, and then transmits
the rear window defogger control signal to IPDM E/R via CAN communication for approximately 15 minutes.
• IPDM E/R turns rear window defogger relay ON when it receives rear window defogger control signal.
• The power is supplied to rear window defogger and door mirror defogger* when the rear window defogger
relay turns ON.
• When rear window defogger is activated, indicator lamp on rear window defogger switch turns ON.
*: For models with door mirror defogger.
TIMER FUNCTION
• BCM transmits rear window defogger control signal to IPDM E/R for approximately 15 minutes when rear
window defogger switch is turns ON while ignition switch is ON. Then, IPDM E/R activates rear window
defogger and door mirror defogger*.
• The timer is cancelled if the rear window defogger switch is pressed again during timer operation. BCM
stops the output of rear window defogger control signal. The same action occurs during timer operation if the
ignition switch is OFF.
*: For models with door mirror defogger.
WITHOUT AUTO A/C
WITHOUT AUTO A/C : System Diagram
INFOID:0000000007579484
JMLIA2593GB
JMLIA2594GB
Revision: 2011 October
2012 JUKE
SYSTEM
DEF-7
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
DEF
N
O
P
WITHOUT AUTO A/C : System Description
INFOID:0000000007579485
OPERATION DESCRIPTION
• BCM detects that rear window defogger switch turns ON while ignition switch is ON, and then transmits rear
window defogger control signal to IPDM E/R via CAN communication for approximately 15 minutes.
• IPDM E/R turns rear window defogger relay ON when it receives rear window defogger control signal.
• The power is supplied to rear window defogger and door mirror defogger* when rear window defogger relay
turns ON.
• When rear window defogger is activated, indicator lamp on rear window defogger switch turns ON.
*: For models with door mirror defogger.
TIMER FUNCTION
• BCM transmits rear window defogger control signal to IPDM E/R for approximately 15 minutes when the rear
window defogger switch is turns ON while ignition switch is ON. Then, IPDM E/R activates rear window
defogger and door mirror defogger*.
• The timer is cancelled if the rear window defogger switch is pressed again during timer operation. BCM
stops the output of rear window defogger control signal. The same action occurs during timer operation if the
ignition switch is OFF.
*: For models with door mirror defogger.
Revision: 2011 October
2012 JUKE
DEF-8
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000007808994
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
NOTE:
*: For models with automatic A/C, this diagnosis mode is not used.
FREEZE FRAME DATA (FFD)
The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT.
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
×
Air conditioning system
AIR CONDITONER
×
×
*
• Intelligent Key system
• Engine start system
INTELLIGENT KEY
×
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
NVIS - NATS
IMMU
×
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Back door open
TRUNK
×
Theft warning alarm
THEFT ALM
×
×
×
RAP
RETAINED PWR
×
Signal buffer system
SIGNAL BUFFER
×
×
TPMS
AIR PRESSURE MONITOR
×
×
×
Revision: 2011 October
2012 JUKE
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
DEF-9
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
DEF
N
O
P
NOTE:
*: Power position shifts to “LOCK” from “OFF”, when ignition switch is in the OFF position, selector lever is in the P position (A/T models
and CVT models), and any of the following conditions are met.
• Closing door
• Opening door
• Door is locked using door request switch
• Door is locked using Intelligent Key
The power position shifts to “ACC” when the push-button ignition switch (push switch) is pushed at “LOCK”.
REAR WINDOW DEFOGGER
REAR WINDOW DEFOGGER : CONSULT Function (BCM - REAR DEFOGGER)
INFOID:0000000007579487
Data monitor
CONSULT screen item
Indication/Unit
Description
Vehicle Speed
km/h
Vehicle speed of the moment a particular DTC is detected
Odo/Trip Meter
km
Total mileage (Odometer value) of the moment a particular DTC is detected
Vehicle Condition
SLEEP>LOCK
Power position status of
the moment a particular
DTC is detected
While turning BCM status from low power consumption mode to
normal mode (Power position is “LOCK”*.)
SLEEP>OFF
While turning BCM status from low power consumption mode to
normal mode (Power position is “OFF”.)
LOCK>ACC
While turning power position from “LOCK”* *to “ACC”
ACC>ON
While turning power position from “ACC” to “IGN”
RUN>ACC
While turning power position from “RUN” to “ACC” (Vehicle is
stopping and selector lever is except P position.)
CRANK>RUN
While turning power position from “CRANKING” to “RUN” (From
cranking up the engine to run it)
RUN>URGENT
While turning power position from “RUN“ to “ACC” (Emergency
stop operation)
ACC>OFF
While turning power position from “ACC” to “OFF”
OFF>LOCK
While turning power position from “OFF” to “LOCK”*
OFF>ACC
While turning power position from “OFF” to “ACC”
ON>CRANK
While turning power position from “IGN” to “CRANKING”
OFF>SLEEP
While turning BCM status from normal mode (Power position is
“OFF”.) to low power consumption mode
LOCK>SLEEP
While turning BCM status from normal mode (Power position is
“LOCK”*.) to low power consumption mode
LOCK
Power position is “LOCK”*
OFF
Power position is “OFF” (Ignition switch OFF)
ACC
Power position is “ACC” (Ignition switch ACC)
ON
Power position is “IGN” (Ignition switch ON with engine stopped)
ENGINE RUN
Power position is “RUN” (Ignition switch ON with engine running)
CRANKING
Power position is “CRANKING” (At engine cranking)
IGN Counter
0 - 39
The number of times that ignition switch is turned ON after DTC is detected
• The number is 0 when a malfunction is detected now.
• The number increases like 1
→
2
→
3...38
→
39 after returning to the normal condition
whenever ignition switch OFF
→
ON.
• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
Revision: 2011 October
2012 JUKE
DEF-10
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
ACTIVE TEST
Monitor Item
Description
REAR DEF SW
Displays “Press (ON)/other (OFF)” status determined with the rear window defogger switch.
PUSH SW
Indicates [ON/OFF] condition of push switch.
Test Item
Description
REAR DEFOGGER
Rear window defogger operates when “ON” on CONSULT screen is touched.
Revision: 2011 October
2012 JUKE
DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
DEF-11
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
DEF
N
O
P
DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000007808995
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
REAR WINDOW DEFOGGER
REAR WINDOW DEFOGGER : CONSULT Function (BCM - REAR DEFOGGER)
INFOID:0000000007579489
Data monitor
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp control
INT LAMP
×
×
×
Remote keyless entry system
MULTI REMOTE ENT
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
Air conditioning system
AIR CONDITONER
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
NATS
IMMU
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Back door open
TRUNK
×
Theft warning alarm
THEFT ALM
×
×
×
RAP system
RETAINED PWR
×
×
Signal buffer system
SIGNAL BUFFER
×
×
Panic alarm
PANIC ALARM
×
TPMS
AIR PRESSUE MONITOR
×
×
×
Revision: 2011 October
2012 JUKE
DEF-12
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
ACTIVE TEST
Monitor Item
Description
REAR DEF SW
Displays “Press (ON)/other (OFF)” status determined with the rear window defogger switch.
IGN ON SW
Indicates [ON/OFF] condition of ignition switch in ON position.
ACC ON SW
Indicates [ON/OFF] condition of ignition switch ACC position.
Test Item
Description
REAR DEFOGGER
Rear window defogger operates when “ON” on CONSULT screen is touched.
Revision: 2011 October
2012 JUKE
DIAGNOSIS SYSTEM (IPDM E/R)
DEF-13
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
DEF
N
O
P
DIAGNOSIS SYSTEM (IPDM E/R)
WITH INTELLIGENT KEY
WITH INTELLIGENT KEY : Diagnosis Description
INFOID:0000000007808996
AUTO ACTIVE TEST
Description
In auto active test mode, the IPDM E/R sends a drive signal to the following systems to check their operation.
• Rear window defogger
• Front wiper motor
• Parking lamp
• License plate lamp
• Tail lamp
• Side marker lamp
• Front fog lamp
• Headlamp (LO, HI)
• A/C compressor (magnet clutch)
• Cooling fan
Operation Procedure
CAUTION:
Wiper arm interferes with food when wiper is operated while wiper arm is in the raised position.
Always perform auto active test without setting wiper arm in the raised position. Always pour water on
front windshield glass in advance to auto active test so that damage on front windshield glass surface
is prevented.
1.
Turn the ignition switch OFF.
2.
Turn the ignition switch ON, and within 20 seconds, press the driver door switch 10 times. Then turn the
ignition switch OFF.
CAUTION:
Close passenger door.
3.
Turn the ignition switch ON within 10 seconds. After that the horn sounds once and the auto active test
starts.
CAUTION:
Engine starts when ignition switch is turned ON while brake pedal is depressed.
4.
After a series of the following operations is repeated 3 times, auto active test is completed.
NOTE:
• When auto active test mode has to be cancelled halfway through test, turn the ignition switch OFF.
• When auto active test is not activated, door switch may be the cause. Check door switch. Refer to
Inspection in Auto Active Test Mode
When auto active test mode is actuated, the following operation sequence is repeated 3 times.
Operation
sequence
Inspection location
Operation
1
Rear window defogger
10 seconds
2
Front wiper motor
LO for 5 seconds
→
HI for 5 seconds
3
• Parking lamp
• License plate lamp
• Tail lamp
• Side marker lamp
• Front fog lamp
10 seconds
4
Headlamp
LO for 10 seconds
→
HI ON
⇔
OFF 5 times
5
A/C compressor (magnet clutch)
ON
⇔
OFF 5 times
6
Cooling fan
50% duty for 5 seconds
→
100% duty for 5 seconds
Revision: 2011 October
2012 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст