Nissan Juke (2012 year). Service Repair Manual — part 115
EM-122
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR16DDT ]
CYLINDER BLOCK
Measure the outer diameter of piston pin with a micrometer (A).
Connecting Rod Bushing Oil Clearance
(Connecting rod bushing oil clearance) = (Connecting rod bushing inner diameter) – (Piston pin outer diame-
ter)
• If the measured value is out of the standard, replace connecting rod assembly and/or piston and piston pin
assembly.
• If replacing piston and piston pin assembly. Refer to
.
• If replacing connecting rod assembly. Refer to
EM-130, "Connecting Rod Bearing"
.
CYLINDER BLOCK TOP SURFACE DISTORTION
• Using a scraper, remove gasket on the cylinder block surface, and also remove engine oil, scale, carbon, or
other contamination.
CAUTION:
Be careful not to allow gasket flakes to enter engine oil or engine coolant passages.
• Measure the distortion on the cylinder block upper face at some
different points in six directions with a straight edge (A) and feeler
gauge (B).
• If it exceeds the limit, replace cylinder block.
MAIN BEARING HOUSING INNER DIAMETER
• Install main bearing cap without main bearings installed, and tighten main bearing cap mounting bolts to the
specified torque. Refer to
EM-111, "Disassembly and Assembly"
.
• Measure the inner diameter of main bearing housing with a bore gauge.
• Measure the position shown in the figure [5 mm (0.20 in)] back-
ward from main bearing housing front side in the 2 directions as
shown in the figure. The smaller one is the measured value.
• If out of the standard, replace cylinder block and main bearing
caps assembly.
NOTE:
Main bearing caps cannot be replaced as a single, because it is machined together with cylinder block.
PISTON TO CYLINDER BORE CLEARANCE
Standard :
PBIC3266J
Standard and Limit
: Refer to
Limit :
Refer
.
PBIC3250J
1
: Cylinder block
2
: Main bearing cap
: Engine front
Standard :
PBIC4005E
Revision: 2011 October
2012 JUKE
CYLINDER BLOCK
EM-123
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
Cylinder Bore Inner Diameter
• Using a bore gauge, measure the cylinder bore for wear, out-of-
round and taper at six different points on each cylinder. [(A) and (B)
directions at (C), (D), and (E)] [(A) is in longitudinal direction of
engine]
NOTE:
When determining cylinder bore grade, measure the cylinder bore
(B) direction at (D) position.
• If the measured value exceeds the limit, or if there are scratches and/or seizure on the cylinder inner wall,
replace cylinder block.
NOTE:
Oversize piston is not provided.
Piston Skirt Diameter
Measure the outer diameter of piston skirt with a micrometer (A).
Piston to Cylinder Bore Clearance
Calculate by piston skirt diameter and cylinder bore inner diameter
[direction (B), position (D)].
(Clearance) = (Cylinder bore inner diameter) – (Piston skirt diame-
ter)
• If it exceeds the limit, replace piston and piston pin assembly and/or cylinder block. Refer to
.
f
: 10 mm (0.39 in)
g
: 60 mm (2.36 in)
h
: 130 mm (5.12 in)
Standard:
Cylinder bore inner diameter
: Refer to
.
Limit:
Out-of-round [Difference between (A) and (B)]
Taper [Difference between (C) and (D)]
: Refer to
.
JPBIA2059ZZ
Standard :
PBIC3272J
A
: Direction A
C
: Position C
E
: Position E
f
: 10 mm (0.39 in)
g
: 60 mm (2.36 in)
h
: 130 mm (5.12 in)
Standard and Limit
: Refer to
.
JPBIA2059ZZ
Revision: 2011 October
2012 JUKE
EM-124
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR16DDT ]
CYLINDER BLOCK
CRANKSHAFT MAIN JOURNAL DIAMETER
• Measure the outer diameter of crankshaft main journals with a
micrometer (A).
• If out of the standard, measure the main bearing oil clearance.
Then use undersize bearing. Refer to
CRANKSHAFT PIN JOURNAL DIAMETER
• Measure the outer diameter of crankshaft pin journal with a micrometer.
• If out of the standard, measure the connecting rod bearing oil clearance. Then use undersize bearing. Refer
EM-144, "Connecting Rod Bearing"
.
OUT-OF-ROUND AND TAPER OF CRANKSHAFT
• Measure the dimensions at four different points as shown in the
figure on each main journal and pin journal with a micrometer.
• Out-of-round is indicated by the difference in dimensions between
(X) and (Y) at (A) and (B).
• Taper is indicated by the difference in dimension between (A) and
(B) at (X) and (Y).
• If the measured value exceeds the limit, correct or replace crankshaft.
• If corrected, measure the bearing oil clearance of the corrected main journal and/or pin journal. Then select
main bearing and/or connecting rod bearing. Refer to
EM-130, "Connecting Rod Bearing"
.
CRANKSHAFT RUNOUT
• Place a V-block on a precise flat table to support the journals on the both end of the crankshaft.
• Place a dial indicator (A) straight up on the No. 3 journal.
• While rotating crankshaft, read the movement of the pointer on the
dial indicator. (Total indicator reading)
• If it exceeds the limit, replace crankshaft.
CONNECTING ROD BEARING OIL CLEARANCE
Method by Calculation
Standard :
PBIC3457J
Standard :
Limit:
Out-of-round [Difference between (X) and (Y)]
Taper [Difference between (A) and (B)]
: Refer to
.
PBIC3459J
Standard and Limit
: Refer to
PBIC3458J
Revision: 2011 October
2012 JUKE
CYLINDER BLOCK
EM-125
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Install connecting rod bearings (2) to connecting rod (3) and con-
necting rod bearing cap (1), and tighten connecting rod cap bolts to
the specified torque. Refer to
EM-111, "Disassembly and Assem-
• Measure the inner diameter of connecting rod bearing with an
inside micrometer.
(Bearing oil clearance) = (Connecting rod bearing inner diameter)
– (Crankshaft pin journal diameter)
• If clearance exceeds the limit, select proper connecting rod bearing according to connecting rod big end
diameter and crankshaft pin journal diameter to obtain specified bearing oil clearance. Refer to
.
Method of Using Plastigage
• Remove engine oil and dust on crankshaft pin and the surfaces of each bearing completely.
• Cut a plastigage slightly shorter than the bearing width, and place it in crankshaft axial direction, avoiding oil
holes.
• Install connecting rod bearings to connecting rod and cap, and tighten connecting rod cap bolts to the speci-
EM-111, "Disassembly and Assembly"
.
CAUTION:
Never rotate crankshaft.
• Remove connecting rod cap and bearing, and using the scale (A)
on the plastigage bag, measure the plastigage width.
NOTE:
The procedure when the measured value exceeds the limit is
same as that described in the “Method by Calculation”.
MAIN BEARING OIL CLEARANCE
Method by Calculation
• Install main bearings (3) to cylinder block (1) and main bearing cap
(2), and tighten main bearing cap mounting bolts to the specified
torque. Refer to
EM-111, "Disassembly and Assembly"
• Measure the inner diameter of main bearing with a bore gauge.
(Bearing oil clearance) = (Main bearing inner diameter) – (Crank-
shaft main journal diameter)
• If clearance exceeds the limit, select proper main bearing according to main bearing inner diameter and
crankshaft main journal diameter to obtain specified bearing oil clearance. Refer to
.
Method of Using Plastigage
• Remove engine oil and dust on crankshaft main journal and the surfaces of each bearing completely.
• Cut a plastigage slightly shorter than the bearing width, and place it in crankshaft axial direction, avoiding oil
holes.
• Install main bearings to cylinder block and main bearing cap, and tighten main bearing cap mounting bolts to
the specified torque. Refer to
EM-111, "Disassembly and Assembly"
.
A
: Example
B
: Inner diameter measuring direction
Standard and Limit
: Refer to
EM-144, "Connecting Rod Bearing"
PBIC3275J
JPBIA4438ZZ
A
: Example
B
: Inner diameter measuring direction
Standard and Limit
: Refer to
.
PBIC3277J
Revision: 2011 October
2012 JUKE
EM-126
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR16DDT ]
CYLINDER BLOCK
CAUTION:
Never rotate crankshaft.
• Remove main bearing cap and bearings, and using the scale (A)
on the plastigage bag, measure the plastigage width.
NOTE:
The procedure when the measured value exceeds the limit is
same as that described in the “Method by Calculation”.
MAIN BEARING CRUSH HEIGHT
• When main bearing cap is removed after being tightened to the
specified torque with main bearings (1) installed, the tip end of
bearing must protrude (B). Refer to
• If the standard is not met, replace main bearings.
CONNECTING ROD BEARING CRUSH HEIGHT
• When connecting rod cap is removed after being tightened to the
specified torque with connecting rod bearings (1) installed, the tip
end of bearing must protrude (B). Refer to
.
• If the standard is not met, replace connecting rod bearings.
MAIN BEARING CAP BOLT OUTER DIAMETER
• Measure the outer diameters (d
1
) and (d
2
) at two positions as
shown in the figure.
• If reduction appears in places other than (B) range, regard it as
(d
2
).
• If it exceeds the limit (a large difference in dimensions), replace
main bearing cap mounting bolt with a new one.
CONNECTING ROD CAP BOLT OUTER DIAMETER
PBIC3278J
A
: Example
Standard
: There must be crush height.
PBIC3279J
A
: Example
Standard
: There must be crush height.
PBIC3279J
A
: (d1) measuring position
B
: (d2) measuring position
Limit [(d
1
) – (d
2
)]: 0.15 mm (0.0059 in)
PBIC4015E
Revision: 2011 October
2012 JUKE
CYLINDER BLOCK
EM-127
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Measure the outer diameter (d) at position as shown in the figure.
• If reduction appears in a position other than (d), regard it as (d).
• When (d) exceeds the limit (when it becomes thinner), replace
connecting rod cap bolt with a new one.
FLYWHEEL DEFLECTION (M/T MODELS)
• Measure the deflection of flywheel contact surface to torque with a
dial indicator (A).
• Measure the deflection at 210 mm (8.27 in) diameter.
• If measured value is out of the standard, replace flywheel.
• If a trace of burn or discoloration is found on the surface, repair it
with sandpaper.
CAUTION:
When measuring, keep magnetic fields (such as dial indicator
stand) away from signal plate of the rear end of crankshaft.
MOVEMENT AMOUNT OF FLYWHEEL (M/T MODELS)
CAUTION:
Never disassemble double mass flywheel.
Movement Amount of Thrust (Fore-and-Aft) Direction
• Measure the movement amount of thrust (fore-and-aft) direction when 100 N (10.2 kg, 22 lb) force is added
at the portion of 125 mm (4.92 in) radius from the center of flywheel.
• If measured value is out of the standard, replace flywheel.
Movement Amount in Radial (Rotation) Direction
Check the movement amount of radial (rotation) direction with the following procedure:
1.
Install clutch cover mounting bolt (1) to clutch cover mounting
hole, and place a torque wrench (A) on the extended line of the
flywheel (2) center line.
• Tighten bolt at a force of 9.8 N·m (1.0 kg-m, 87 in-lb) to keep it
from loosening.
2.
Put a mating mark on circumferences of the two flywheel
masses without applying any load (Measurement standard
points).
3.
Apply a force of 9.8 N·m (1.0 kg-m, 87 in-lb) in each direction,
and mark the movement amount on the mass on the transaxle
side.
4.
Measure the dimensions of movement amounts “A” and “B” on
circumference of the flywheel on the transaxle side.
• If measured value is out of the standard, replace flywheel.
DRIVE PLATE DEFLECTION (CVT MODELS)
Limit: 7.75 mm (0.3051 in)
PBIC4016E
Limit : 0.45 mm (0.0177 in) or less.
PBIC4006E
Standard
: 1.8 mm (0.071 in) or less
Limit
: 33.2 mm (1.307 in) or less.
PBIC4007E
Revision: 2011 October
2012 JUKE
EM-128
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR16DDT ]
CYLINDER BLOCK
• Measure the deflection of drive plate contact surface to torque con-
verter with a dial indicator (A).
• Measure the deflection at the area limited between 12.4 mm
(0.488 in) dia and 20.0 mm (0.787 in) dia around hole (B).
• If measured value is out of the standard, replace drive plate.
Limit : 0.35 mm (0.0138 in) or less.
PBIC4008E
Revision: 2011 October
2012 JUKE
HOW TO SELECT PISTON AND BEARING
EM-129
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
HOW TO SELECT PISTON AND BEARING
Description
INFOID:0000000007577490
• The identification grade stamped on each part is the grade for the dimension measured in new condition.
This grade cannot apply to reused parts.
• For reused or repaired parts, measure the dimension accurately. Determine the grade by comparing the
measurement with the values of each selection table.
• For details of the measurement method of each part, the reuse standards and the selection method of the
selective fitting parts, refer to the text.
Piston
INFOID:0000000007577491
WHEN NEW CYLINDER BLOCK IS USED
• Check the cylinder bore grade on rear left side of cylinder block (L),
and select piston of the same grade.
• If there is a correction stamp mark on the cylinder block, use it as a
correct reference.
WHEN CYLINDER BLOCK IS REUSED
1.
Measure the cylinder bore inner diameter. Refer to
.
2.
Determine the bore grade by comparing the measurement with the values under the cylinder bore inner
diameter of the “Piston Selection Table”.
Selection points
Selection parts
Selection items
Selection methods
Between cylinder block and
crankshaft
Main bearing
Main bearing grade (bearing
thickness)
Determined by match of cylin-
der block bearing housing
grade (inner diameter of hous-
ing) and crankshaft journal
grade (outer diameter of jour-
nal)
Between crankshaft and con-
necting rod
Connecting rod bearing
Connecting rod bearing grade
(bearing thickness)
Combining service grades for
connecting rod big end diame-
ter and crankshaft pin outer di-
ameter determine connecting
rod bearing selection.
Between cylinder block and pis-
ton
Piston and piston pin assembly
(piston is available together with
piston pin as an assembly.)
Piston grade (piston outer diam-
eter)
Piston grade = cylinder bore
grade (inner diameter of bore)
A
: Correction stamp
B
: Standard stamp
C
: Cylinder No. 1 bore grade
D
: Cylinder No. 2 bore grade
E
: Cylinder No. 3 bore grade
F
: Cylinder No. 4 bore grade
G
: No. 1 main bearing housing grade
H
: No. 2 main bearing housing grade
I
: No. 3 main bearing housing grade
J
: No. 4 main bearing housing grade
K
: No. 5 main bearing housing grade
: Engine front
PBIC3264J
Revision: 2011 October
2012 JUKE
EM-130
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR16DDT ]
HOW TO SELECT PISTON AND BEARING
3.
Select piston of the same grade.
PISTON SELECTION TABLE
Unit: mm (in)
NOTE:
Piston is available together with piston pin as an assembly.
Connecting Rod Bearing
INFOID:0000000007577492
WHEN NEW CONNECTING ROD AND CRANKSHAFT ARE USED
1.
Apply connecting rod big end diameter grade stamped on con-
necting rod side face to the row in the “Connecting Rod Bearing
Selection Table”.
2.
Apply crankshaft pin journal diameter grade stamped on crank-
shaft front side to the column in the “Connecting Rod Bearing
Selection Table”.
3.
Read the symbol at the cross point of selected row and column in the “Connecting Rod Bearing Selection
Table”.
4.
Apply the symbol obtained to the “Connecting Rod Bearing Grade Table” to select connecting rod bearing.
WHEN CONNECTING ROD AND CRANKSHAFT ARE REUSED
1.
Measure the dimensions of the connecting rod big end diameter and crankshaft pin journal diameter indi-
vidually. Refer to
.
A
: Identification code
B
: Piston grade number
C
: Front mark
D
: Sub grade number
JPBIA4439ZZ
Grade number (Mark)
1
2 [or no mark (piston only)]
Cylinder bore Inner diameter
79.700 - 79.710 (3.1378 - 3.1382)
79.710 - 79.720 (3.1382 - 3.1386)
Piston skirt diameter
79.670 - 79.680 (3.1366 - 3.1370)
79.680 - 79.690 (3.1370 - 3.1374)
A
: Oil hole
B
: Management code
C
: Cylinder number
D
: Big end diameter grade
E
: Front mark
JPBIA4442ZZ
A
: No. 1 pin journal diameter grade
B
: No. 2 pin journal diameter grade
C
: No. 3 pin journal diameter grade
D
: No. 4 pin journal diameter grade
E
: No. 1 main journal diameter grade
F
: No. 2 main journal diameter grade
G
: No. 3 main journal diameter grade
H
: No. 4 main journal diameter grade
I
: No. 5 main journal diameter grade
PBIC3261J
Revision: 2011 October
2012 JUKE
HOW TO SELECT PISTON AND BEARING
EM-131
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
2.
Apply the measured dimension to the “Connecting Rod Bearing Selection Table”.
3.
Read the symbol at the cross point of selected row and column in the “Connecting Rod Bearing Selection
Table”.
4.
Apply the symbol obtained to the “Connecting Rod Bearing Grade Table” to select connecting rod bearing.
CONNECTING ROD BEARING SELECTION TABLE
CONNECTING ROD BEARING GRADE TABLE
UNDERSIZE BEARINGS USAGE GUIDE
• When the specified connecting rod bearing oil clearance is not obtained with standard size connecting rod
bearings, use undersize (US) bearings.
• When using undersize (US) bearing, measure the connecting rod bearing inner diameter with bearing
installed, and grind the crankshaft pin so that the connecting rod bearing oil clearance satisfies the standard.
CAUTION:
PBIC4077E
Connecting rod bearing grade table
: Refer to
EM-144, "Connecting Rod Bearing"
.
Revision: 2011 October
2012 JUKE
EM-132
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR16DDT ]
HOW TO SELECT PISTON AND BEARING
In grinding crankshaft pin to use undersize bearings, keep the
fillet R [1.5 - 1.7 mm (0.059 - 0.067 in)] (A).
Main Bearing
INFOID:0000000007577493
WHEN NEW CYLINDER BLOCK AND CRANKSHAFT ARE USED
1.
“Main Bearing Selection Table” rows correspond to main bearing
housing grade on rear left side of cylinder block (L).
• If there is a correction stamp mark on cylinder block, use it as
a correct reference.
2.
Apply main journal diameter grade stamped on crankshaft front
side to column in the “Main Bearing Selection Table”.
3.
Read the symbol at the cross point of selected row and column in the “Main Bearing Selection Table”.
CAUTION:
There are two main bearing selection tables. One is for No. 1, 4, and 5 journals and the other is for
No. 2 and 3 journals. Make certain to use the appropriate table. This is due to differences in the
specified clearances.
Bearing undersize table
: Refer to
EM-144, "Connecting Rod Bearing"
PBIC3263J
A
: Correction stamp
B
: Standard stamp
C
: Cylinder No. 1 bore grade
D
: Cylinder No. 2 bore grade
E
: Cylinder No. 3 bore grade
F
: Cylinder No. 4 bore grade
G
: No. 1 main bearing housing grade
H
: No. 2 main bearing housing grade
I
: No. 3 main bearing housing grade
J
: No. 4 main bearing housing grade
K
: No. 5 main bearing housing grade
: Engine front
PBIC3264J
A
: No. 1 pin journal diameter grade
B
: No. 2 pin journal diameter grade
C
: No. 3 pin journal diameter grade
D
: No. 4 pin journal diameter grade
E
: No. 1 main journal diameter grade
F
: No. 2 main journal diameter grade
G
: No. 3 main journal diameter grade
H
: No. 4 main journal diameter grade
I
: No. 5 main journal diameter grade
PBIC3261J
Revision: 2011 October
2012 JUKE
HOW TO SELECT PISTON AND BEARING
EM-133
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
4.
Apply the symbol obtained to the “Main Bearing Grade Table” to select main bearing.
NOTE:
Service part is available as a set of both upper and lower.
WHEN CYLINDER BLOCK AND CRANKSHAFT ARE REUSED
1.
Measure the dimensions of the cylinder block main bearing housing inner diameter and crankshaft main
journal diameter individually. Refer to
2.
Apply the measured dimension to the “Main Bearing Selection Table”.
3.
Read the symbol at the cross point of selected row and column in the “Main Bearing Selection Table”.
CAUTION:
There are two main bearing selection tables. One is for No. 1, 4, and 5 journals and the other is for
No. 2 and 3 journals. Make certain to use the appropriate table. This is due to differences in the
specified clearances.
4.
Apply the symbol obtained to the “Main Bearing Grade Table” to select main bearing.
NOTE:
Service part is available as a set of both upper and lower.
MAIN BEARING SELECTION TABLE (No. 1, 4, AND 5 JOURNAL)
PBIC4078E
Revision: 2011 October
2012 JUKE
EM-134
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR16DDT ]
HOW TO SELECT PISTON AND BEARING
MAIN BEARING SELECTION TABLE (No. 2 AND 3 JOURNAL)
MAIN BEARING GRADE TABLE (ALL JOURNALS)
UNDERSIZE BEARING USAGE GUIDE
• When the specified main bearing oil clearance is not obtained with standard size main bearings, use under-
size (US) bearing.
• When using undersize (US) bearing, measure the main bearing inner diameter with bearing installed, and
grind main journal so that the main bearing oil clearance satisfies the standard.
CAUTION:
In grinding crankshaft main journal to use undersize bearings,
keep the fillet R [1.5 - 1.7 mm (0.059 - 0.067 in)] (A).
JPBIA4443GB
Main bearing grade table (All journals)
: Refer to
Bearing undersize table:
PBIC3263J
Revision: 2011 October
2012 JUKE
SERVICE DATA AND SPECIFICATIONS (SDS)
EM-135
< SERVICE DATA AND SPECIFICATIONS (SDS)
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specification
INFOID:0000000007577494
GENERAL SPECIFICATIONS
Unit: degree
(
): Valve timing control “ON”
Drive Belt
INFOID:0000000007577495
DRIVE BELT
Spark Plug
INFOID:0000000007577496
SPARK PLUG
Unit: mm (in)
Engine type
MR16DDT
Cylinder arrangement
In-line 4
Displacement cm
3
(cu in)
1,618 (98.78)
Bore and stroke mm (in)
79.7
×
81.1 (3.138
×
3.193)
Valve arrangement
DOHC
Firing order
1-3-4-2
Number of piston rings
Compression
2
Oil
1
Compression ratio
9.5
Compression pressure
kPa (kg/cm
2
, psi)/250 rpm
Standard
1,560 (15.9, 226.2)
Minimum
1,190 (12.1, 172.6)
Differential limit between cylinders
100 (1.0, 14.5)
Valve timing
: Intake valve
: Exhaust valve
a
b
c
d
e
f
228
228
11 (
−
31)
ATDC
59 (17)
ABDC
4 (61)
ATDC
44 (-13)
BBDC
JPBIA4228ZZ
Tension of drive belt
Belt tension is not necessary, as it is automatically adjusted by drive belt auto-tensioner.
Make
NTK
Standard type
DILKAR7C9H
Gap (Nominal)
Standard
0.9 (0.035)
Limit
1.1 (0.043)
Revision: 2011 October
2012 JUKE
EM-136
< SERVICE DATA AND SPECIFICATIONS (SDS)
[MR16DDT ]
SERVICE DATA AND SPECIFICATIONS (SDS)
Exhaust Manifold
INFOID:0000000007577497
EXHAUST MANIFOLD
Unit: mm (in)
Turbocharger
INFOID:0000000007577498
TURBOCHARGER ACTUATOR
Camshaft
INFOID:0000000007577499
CAMSHAFT
Unit: mm (in)
*: Total indicator reading
VALVE LIFTER
Unit: mm (in)
Items
Limit
Surface distortion
Each exhaust port
0.1 (0.004)
Entire part
0.3 (0.012)
Value of pressure
Value of rod moving
Standard
68.4 kPa (513 mmHg, 20.19 inHg)
1 mm (0.039 in)
Items
Standard
Limit
Camshaft journal oil clearance
No. 1
0.045 - 0.086 (0.0018 - 0.0034)
0.15 (0.0059)
No. 2, 3, 4, 5
0.030 - 0.071 (0.0012 - 0.0028)
Camshaft bracket inner diameter
No. 1
28.000 - 28.021 (1.1024 - 1.1032)
—
No. 2, 3, 4, 5
25.000 - 25.021 (0.9843 - 0.9851)
—
Camshaft journal diameter
No. 1
27.935 - 27.955 (1.0998 - 1.1006)
—
No. 2, 3, 4, 5
24.950 - 24.970 (0.9823 - 0.9831)
—
Camshaft end play
0.075 - 0.153 (0.0030 - 0.0060)
0.24 (0.0094)
Camshaft cam height “A”
Intake
44.605 - 44.795 (1.7561 - 1.7636)
44.66 (1.75827)
Exhaust
43.175 - 43.365 (1.6998 - 1.7073)
44.20 (1.74016)
Camshaft runout [TIR*]
Less than 0.02 (0.0008)
0.05 (0.0020)
Camshaft sprocket runout [TIR*]
—
0.15 (0.0059)
SEM671
Items
Standard
Valve lifter outer diameter
Intake
33.977 - 33.987 (1.3377 - 1.3381)
Exhaust
29.977 - 29.987 (1.1802 - 1.1806)
Revision: 2011 October
2012 JUKE
SERVICE DATA AND SPECIFICATIONS (SDS)
EM-137
< SERVICE DATA AND SPECIFICATIONS (SDS)
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
VALVE CLEARANCE
Unit: mm (in)
*: Approximately 80
°
C (176
°
F)
AVAILABLE VALVE LIFTER
Unit: mm (in)
Valve lifter hole diameter
Intake
34.000 - 34.021 (1.3386 - 1.3394)
Exhaust
30.000 - 30.021 (1.1811 - 1.1819)
Valve lifter clearance
0.013 - 0.044 (0.0005 - 0.0017)
Items
Cold
Hot* (reference data)
Intake
0.24 - 0.32 (0.009 - 0.013)
0.304 - 0.416 (0.012 - 0.016)
Exhaust
0.25 - 0.33 (0.01 - 0.013)
0.308 - 0.432 (0.012 - 0.017)
Identification mark
Thickness
300
3.00 (0.1181)
302
3.02 (0.1189)
304
3.04 (0.1197)
306
3.06 (0.1205)
308
3.08 (0.1213)
310
3.10 (0.1220)
312
3.12 (0.1228)
314
3.14 (0.1236)
316
3.16 (0.1244)
318
3.18 (0.1252)
320
3.20 (0.1260)
322
3.22 (0.1268)
324
3.24 (0.1276)
326
3.26 (0.1283)
328
3.28 (0.1291)
330
3.30 (0.1299)
332
3.32 (0.1307)
334
3.34 (0.1315)
336
3.36 (0.1323)
338
3.38 (0.1331)
340
3.40 (0.1339)
342
3.42 (0.1346)
344
3.44 (0.1354)
KBIA0119E
Revision: 2011 October
2012 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст