Nissan Juke (2012 year). Service Repair Manual — part 36
REPLACEMENT OPERATIONS
BRM-59
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
• Perform the hemming to the flange of wheelarch after applying the
adhesive.
• Apply the sealing to the flange end.
• Refer to
BRM-31, "Rear Fender Hemming Process"
.
1.
Outer rear wheelhouse
2.
Rear fender
3.
Adhesive
4.
Sealant
JSKIA0204GB
Revision: 2011 October
2012 JUKE
BRM-60
< REMOVAL AND INSTALLATION >
REPLACEMENT OPERATIONS
Rear Fender Extension (2WD Models)
INFOID:0000000007578134
1.
Body sealing
Replacement parts
z
Rear fender corner (LH)
JSKIA2025ZZ
Revision: 2011 October
2012 JUKE
REPLACEMENT OPERATIONS
BRM-61
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
Rear Fender Extension (AWD Models)
INFOID:0000000007578135
1.
Body sealing
Replacement parts
z
Rear fender corner (LH)
JSKIA2180ZZ
Revision: 2011 October
2012 JUKE
BRM-62
< REMOVAL AND INSTALLATION >
REPLACEMENT OPERATIONS
Rear Panel (2WD Models)
INFOID:0000000007578136
Unit: mm (in)
: Vehicle front
: Welding method, the number of welding points, and the distance in the figure apply to both side of the vehicle.
Replacement parts
z
Upper rear panel
JSKIA2522GB
Revision: 2011 October
2012 JUKE
REPLACEMENT OPERATIONS
BRM-63
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
Rear Panel (AWD Models)
INFOID:0000000007578137
Rear Floor Rear (2WD Models)
INFOID:0000000007578138
Work after rear panel is removed.
Unit: mm (in)
: Vehicle front
: Welding method, the number of welding points, and the distance in the figure apply to both side of the vehicle.
Replacement parts
z
Upper rear panel
JSKIA2523GB
Revision: 2011 October
2012 JUKE
BRM-64
< REMOVAL AND INSTALLATION >
REPLACEMENT OPERATIONS
Rear Floor Rear (AWD Models)
INFOID:0000000007578139
Work after rear panel is removed.
: Vehicle front
: Welding method and the number of welding points apply to both side of the vehicle.
: Weld the parts onto the back of the component part.
Replacement parts
z
Rear floor rear
z
Spare tire clamp bracket
z
Rear towing hook bracket
z
Muffler mounting bracket
z
Canister bracket (rear)
z
Spare wheel clamp reinforcement
z
Canister mounting bracket
JSKIA2208ZZ
Revision: 2011 October
2012 JUKE
REPLACEMENT OPERATIONS
BRM-65
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
Rear Side Member (AWD Models Partial Replacement)
INFOID:0000000007578140
Work after rear panel and rear floor rear are removed.
: Vehicle front
: Welding method and the number of welding points apply to both side of the vehicle.
Replacement parts
z
Rear floor rear
z
Spare tire clamp bracket
z
Jack mounting bracket
z
Canister bracket
z
Spare wheel clamp reinforcement
JSKIA2209ZZ
Revision: 2011 October
2012 JUKE
BRM-66
< REMOVAL AND INSTALLATION >
REPLACEMENT OPERATIONS
Rear Side Member Extension (2WD Models)
INFOID:0000000007578141
Work after rear panel is removed.
Unit: mm (in)
: Vehicle front
: Weld the parts onto the back of the component part.
Replacement parts
z
Rear side member (LH)
JSKIA2188GB
Revision: 2011 October
2012 JUKE
REPLACEMENT OPERATIONS
BRM-67
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
Rear Side Member Extension (AWD Models)
INFOID:0000000007578142
Work after rear panel is removed.
: Vehicle front
: Weld the parts onto the back of the component part.
Replacement parts
z
Rear side member extension (LH)
JSKIA2032ZZ
Revision: 2011 October
2012 JUKE
BRM-68
< REMOVAL AND INSTALLATION >
REPLACEMENT OPERATIONS
: Vehicle front
: Weld the parts onto the back of the component part.
Replacement parts
z
Rear side member extension (LH)
JSKIA2189ZZ
Revision: 2011 October
2012 JUKE
BODY ALIGNMENT
BRM-69
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
BODY ALIGNMENT
Body Center Marks
INFOID:0000000007578143
A mark is placed on each part of the body to indicate the vehicle center. When repairing the vehicle frame
(members, pillars, etc.) damaged by an accident which it enables more accurate and effective repair by using
these marks together with body alignment specifications.
Unit: mm (in)
: Vehicle front
Points
Portion
Marks
A
Front roof
Embossment
B
Cowl top
Embossment
C
Upper dash
Embossment
D
Trans control reinforcement
Hole
φ
16 (0.63)
JSKIA2144ZZ
Revision: 2011 October
2012 JUKE
BRM-70
< SERVICE DATA AND SPECIFICATIONS (SDS)
BODY ALIGNMENT
Description
INFOID:0000000007578144
• All dimensions indicated in the figures are actual.
• When using a tracking gauge, adjust both pointers to equal length. Then check the pointers and gauge itself
to make sure there is no free play.
• When a measuring tape is used, check to be sure there is no elongation, twisting or bending.
• Measurements should be taken at the center of the mounting holes.
• An asterisk (*) following the value at the measuring point indicates that the measuring point on the other side
is symmetrically the same value.
• The coordinates of the measurement points are the distances measured from the standard line of
″
X
″
,
″
Y
″
and
″
Z
″
.
•
″
Z
″
: Imaginary base line [200 mm (7.87 in) below datum line (
″
0Z
″
at design plan)]
Engine Compartment
INFOID:0000000007578145
MEASUREMENT
Dimensions marked with
″
*
″
indicate symmetrically identical dimensions on both the right and left hand of the
vehicle.
E
Parking brake reinforcement
Hole
φ
12 (0.47)
F
Rear panel
Indent
G
Rear roof
Embossment
Points
Portion
Marks
1.
Vehicle center
2.
Front axle center
3.
Imaginary base line
JSKIA0073GB
Revision: 2011 October
2012 JUKE
BODY ALIGNMENT
BRM-71
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
«The others»
Unit: mm (in)
MEASUREMENT POINTS
Unit: mm (in)
Point
Dimension
Memo
Point
Dimension
Memo
Point
Dimension
Memo
Point
Dimension
Memo
A - C
729 (28.70)*
B - E
298 (11.73)*
D - d
1429 (56.26)
G - h
1192 (46.93)*
A - D
729 (28.70)*
B - e
1233 (48.54)*
E - e
1037 (40.83)
J - j
958 (37.72)
A - F
798 (31.42)*
C - c
1441 (56.73)
F - f
1366 (53.78)
JSKIA2151GB
Revision: 2011 October
2012 JUKE
BRM-72
< SERVICE DATA AND SPECIFICATIONS (SDS)
BODY ALIGNMENT
Unit: mm (in)
: Vehicle front
JSKIA2152ZZ
Point
Material
Point
Material
A
Upper dash positioning mark of center position-
ing mark
G, g, H, h
Upper radiator core support hole center
G, g:
φ
12 (0.47)
H, h: 14
×
12 (0.55
×
0.47)
B, b
Hoodledge reinforcement hole center 14
×
10
(0.55
×
0.39)
J
Front side member hole center
φ
7 (0.28)
C, c, F, f
Front fender installing hole center
φ
7 (0.28)
j
Engine mounting bracket hole center
φ
11 (0.43)
D, d
Front combination lamp installing hole center
φ
7
(0.28)
K, k, M, m
Front bumper stay installing hole center
φ
15
(0.59)
E, e
Front strut installing hole center 16
×
10
(0.63
×
0.39)
Revision: 2011 October
2012 JUKE
BODY ALIGNMENT
BRM-73
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
Underbody (2WD Models)
INFOID:0000000007578146
MEASUREMENT
Dimensions marked with
″
*
″
indicate symmetrically identical dimensions on both the right and left hand of the
vehicle.
The following figure shows a bottom view and a side view of the vehicle.
JSKIA1991GB
Revision: 2011 October
2012 JUKE
BRM-74
< SERVICE DATA AND SPECIFICATIONS (SDS)
BODY ALIGNMENT
MEASUREMENT POINTS
Unit: mm (in)
Unit: mm (in)
: Vehicle front
: Vehicle left side
: Vehicle front
Points
Coordinates
Remarks
Points
Coordinates
Remarks
X
Y
Z
X
Y
Z
A
473.5
(18.642)
−
557.0
(
−
21.929)
293.0
(11.535)
Hole
φ
11 (0.43)
H, h
±
482.3
(
±
18.988)
2374.2
(93.472)
348.3
(13.713)
Hole
φ
12 (0.47)
a
−
491.0
(
−
19.331)
−
557.0
(
−
21.929)
301.9
(11.886)
Hole
φ
11 (0.43)
J
499.5
(19.665)
2448.0
(96.378)
378.0
(14.882)
Hole
φ
21 (0.83)
B
472.4
(18.598)
−
455.0
(
−
17.913)
328.9
(12.949)
Hole
φ
18 (0.71)
j
−
487.5
(
−
19.193)
2448.0
(96.378)
378.0
(14.882)
Hole
φ
21 (0.83)
JSKIA2153ZZ
Revision: 2011 October
2012 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст