Nissan Murano Z50 (2005 year). Manual — part 38
REAR DOOR LOCK
BL-177
C
D
E
F
G
H
J
K
L
M
A
B
BL
Revision: 2005 August
2005 Murano
REAR DOOR LOCK
PFP:82502
Component Structure
AIS002BC
Removal and Installation
AIS002BD
REMOVAL
1.
Remove the rear door finisher. Refer to
2.
Disconnect the inside handle knob cable and lock knob cable
from the back side of the rear door finisher.
3.
Remove the rear door sash. Refer to
GW-70, "REAR DOOR GLASS AND REGULATOR"
.
4.
Remove the rear door window and rear door screen assembly. Refer to
5.
Remove door side grommet, and remove outside handle escutcheon bolt (TORX T30) from grommet
hole.
1.
Front gasket
2.
Outside handle
3.
Outside handle escutcheon
4.
Rear gasket
5.
Outside handle bracket
6.
Grommet
7.
Outside handle cable
8.
Door lock assembly
9.
Inside handle knob cable
10. Lock knob cable
11.
Inside handle
PIIB4830E
PIIA4014E
BL-178
REAR DOOR LOCK
Revision: 2005 August
2005 Murano
CAUTION:
Do not forcibly remove the TORX bolts (T30).
6.
While pulling the outside handle, remove outside handle
escutcheon.
7.
While pulling outside handle, slide toward rear of vehicle to
remove outside handle.
8.
Remove the front gasket and rear gasket.
PIIA3553E
PIIA6344E
PIIA3555E
PIIA3557E
REAR DOOR LOCK
BL-179
C
D
E
F
G
H
J
K
L
M
A
B
BL
Revision: 2005 August
2005 Murano
9.
Remove the TORX bolts (T30), remove the door lock assembly.
10. Remove the TORX bolt (T30), and remove the outside handle
bracket.
11. While pulling outside handle, slide toward rear of vehicle to
remove outside handle.
12. Disconnect the door lock actuator connector and remove the door lock assembly.
13. Reach to separate outside handle cable connection.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
To install each rod, be sure to rotate the rod holder until a click is felt.
PIIA1090E
PIIB5076E
PIIA3558E
PIIA5059E
BL-180
BACK DOOR
Revision: 2005 August
2005 Murano
BACK DOOR
PFP:90100
Fitting Adjustment
AIS002BF
VERTICAL/LATERAL CLEARANCE ADJUSTMENT
1.
Loosen the back door striker mounting screw, and close the back door lightly.
2.
Adjust the surface height with the bumper rubber (upper/lower).
NOTE:
●
Rotate the bumper rubber (upper) to adjust the height.
●
Rotate the TORX (T20) bolt of the bumper rubber (lower) to adjust the height.
3.
After adjusting the surface hight, open the door and tighten the back door striker mounting screw and
bumper rubber (upper) lock nuts to the specified torque.
1.
Bumper rubber (upper)
2.
Bumper rubber (lower)
3.
Back door striker
4.
Screw
PIIA3915E
BACK DOOR
BL-181
C
D
E
F
G
H
J
K
L
M
A
B
BL
Revision: 2005 August
2005 Murano
Back Door Assembly
AIS002BG
REMOVAL
CAUTION:
Before servicing SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 min-
utes.
1.
Remove the headlining. Refer to
EI-36, "Removal and Installation"
2.
Disconnect the back door harness connector.
3.
Remove the high mount stop lamp cover.
4.
Washer hose is separated in the connection part.
5.
Remove the viral tape which tight the back door harness and SRS curtain air bag harness.
6.
Support the back door lock with a proper material to prevent it
from falling.
WARNING:
Body injury may occur if no supporting rod is holding the
back door open when removing the back door stay.
7.
Remove back door stay on back door.
8.
Remove hinge mounting bolts on the back door and remove
back door assembly.
CAUTION:
Do not loosen hinge mounting bolt A and D.
PIIA3916E
PIIA4013E
PIIA3917E
PIIA3918E
BL-182
BACK DOOR
Revision: 2005 August
2005 Murano
INSTALLATION
Install in the reverse order of removal.
CAUTION:
●
Operate with two workers, because of its heavy weight.
●
After installing, check operation.
●
After installing, perform fitting adjustment Refer to
INSPECTION
1.
Check hinges for the following items.
●
Malfunction noise or door closing and opening effort
●
Component wear or damage
2.
Apply Grease to the rotating part of the hinge.
Removal and Installation of Back Door Striker
AIS002BH
REMOVAL
1.
Remove luggage finisher lower. Refer to
2.
Remove mounting screws, and remove striker from the vehicle.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
After installing, perform fitting adjustment.
Removal and Installation of Back Door Stay
AIS002BI
REMOVAL
1.
Support the back door lock with a proper material to prevent it
from falling.
WARNING:
Body injury may occur if no supporting rod is holding the
back door open when removing the back door stay.
PIIA3918E
PIIA3920E
PIIA4013E
BACK DOOR
BL-183
C
D
E
F
G
H
J
K
L
M
A
B
BL
Revision: 2005 August
2005 Murano
2.
Remove back door stay on back door.
3.
Remove back door stay assembly bracket adjusting nuts and
remove back door stay assembly.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
After installing, check operation.
Removal and Installation of Back Door Weatherstrip
AIS002BJ
REMOVAL
Pull up and remove engagement with body from wetherstrip joint.
CAUTION:
After removal, do not pull strongly on the wetherstrip.
INSTALLATION
1.
Working from the upper section, align weatherstrip mark with vehicle center position mark and install
weatherstrip onto the vehicle.
2.
For the lower section, align the weatherstrip seam with center of the striker.
3.
After installation, pull the weatherstrip gently to ensure that there is no loose section.
PIIA3917E
PIIA3919E
1.
Weatherstrip mark
2.
Weatherstrip
PIIB2269J
BL-184
BACK DOOR
Revision: 2005 August
2005 Murano
NOTE:
Make sure the weatherstrip is fit tightly at each corner and back door rear plate.
Emergency unlock lever
AIS006ET
NOTE:
If the back door cannot be opened with the back door lock opener switch or remote controller to a discharged
battery, follow the next steps.
1.
Remove back door finisher cover.
2.
Move the emergency unlock lever to open the back door.
PIIB4832E
BACK DOOR LOCK ASSEMBLY
BL-185
C
D
E
F
G
H
J
K
L
M
A
B
BL
Revision: 2005 August
2005 Murano
BACK DOOR LOCK ASSEMBLY
PFP:90504
Removal and Installation of Back Door Lock
AIS002BK
REMOVAL
1.
Remove back door finisher. Refer to
EI-40, "Removal and Installation"
.
2.
Disconnect back door lock assembly connector.
3.
Remove the mounting bolts.
4.
Remove the mounting bolts, remove back door lock assembly.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
●
After installing, check operation.
●
After installing, perform fitting adjustment. Refer to
INSPECTION
1.
Check back door lock for the following items.
●
Malfunction noise or back door closing and opening effort
●
Component wear or damage
2.
Apply body grease to the rotating part of the back door lock.
PIIB4833E
BL-186
BACK DOOR LOCK ASSEMBLY
Revision: 2005 August
2005 Murano
Removal and Installation of Back Door Opener switch
AIS002BL
REMOVAL
1.
Remove back door finisher. Refer to
EI-40, "Removal and Installation"
.
2.
Remove license plate lamp assembly. Refer to
3.
Disconnect back door opener switch harness connector.
4.
Remove back door opener switch by pushing pawls with screwdriver.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
●
After installing, check operation.
PIIB4831E
BACK DOOR OPENER
BL-187
C
D
E
F
G
H
J
K
L
M
A
B
BL
Revision: 2005 August
2005 Murano
BACK DOOR OPENER
PFP:90550
Component Parts and Harness Connector Location
AIS006DH
System Description / Without Intelligent Key
AIS006DI
Power is supplied at all times
●
through 50A fusible link (letter F, located in the fuse and fusible link box)
●
to BCM terminal 55,
PIIB4828E
BL-188
BACK DOOR OPENER
Revision: 2005 August
2005 Murano
●
through 10A fuse [No.18, located in the fuse block (J/B)]
●
to BCM terminal 42
●
through 10A fuse [No.35, located in the fuse block (J/B)]
●
to back door opener relay terminal 3.
Ground is supplied
●
to BCM terminal 52
●
through body grounds E13, E26 and E28.
When back door opener switch is ON (pushed) with passenger side door unlocked
Ground is supplied
●
to BCM terminal 30
●
through front door lock actuator passenger side terminals 1and 26
●
through back door opener switch terminals 1and 2
●
through body grounds B7 and B20.
Power is supplied
●
through BCM terminal 68
●
to back door opener relay terminal 1
Ground is supplied
●
to back door opener relay terminal 2
●
through body grounds B7 and B20.
When back door opener relay is turned ON,
And power is supplied
●
to back door opener relay terminal 5
●
through back door lock assembly terminals 1 and 2
●
through body grounds B7 and B20.
Then back door lock assembly opens back door.
System Description / With Intelligent Key
AIS006EL
Power is supplied at all times
●
through 50A fusible link (letter F, located in the fuse and fusible link box)
●
to BCM terminal 55,
●
through 10A fuse [No.18, located in the fuse block (J/B)]
●
to BCM terminal 42
●
through 10A fuse [No.35, located in the fuse block (J/B)]
●
to back door opener relay terminal 3.
●
through 10A fuse [No.22, located in the fuse block (J/B)]
●
to Intelligent Key unit terminal 11.
Ground is supplied
●
to BCM terminal 52
●
through body grounds E13, E26 and E28.
●
to Intelligent Key unit terminal 12
●
through body grounds M14 and M78.
When back door opener switch is ON (pushed) with passenger side door unlocked
Ground is supplied
●
to Intelligent Key unit terminal 24
●
through back door opener switch terminals 1and 2
●
through body grounds B7 and B20.
Ground is supplied
●
to back door opener relay terminal 2
●
through Intelligent Key unit terminal 23.
When back door opener relay is turned ON,
BACK DOOR OPENER
BL-189
C
D
E
F
G
H
J
K
L
M
A
B
BL
Revision: 2005 August
2005 Murano
And power is supplied
●
to back door opener relay terminal 5
●
through back door lock assembly terminals 1 and 2
●
through body grounds B7 and B20.
Then back door lock assembly opens back door.
INTELLIGENT KEY OPERATION
Refer to
BL-190
BACK DOOR OPENER
Revision: 2005 August
2005 Murano
Schematic / With Intelligent Key
AIS006EM
TIWB0292E
BACK DOOR OPENER
BL-191
C
D
E
F
G
H
J
K
L
M
A
B
BL
Revision: 2005 August
2005 Murano
Wiring Diagram —B/DOOR— / With Intelligent Key
AIS006DJ
TIWB0162E
BL-192
BACK DOOR OPENER
Revision: 2005 August
2005 Murano
TIWB0163E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст