Nissan Murano Z50 (2005 year). Manual — part 217
REAR SEAT
SE-113
C
D
E
F
G
H
J
K
L
M
A
B
SE
Revision: 2005 August
2005 Murano
RH SIDE SEAT
PIIB4962E
SE-114
REAR SEAT
Revision: 2005 August
2005 Murano
REMOVAL
1.
Remove the leg cover.
2.
Remove the seat mounting bolts.
3.
Fold the seatback forward.
4.
Remove the seat outer side cover.
5.
Remove the seat mounting bolts.
6.
Remove the remote control wire.
7.
Remove the seat mounting bolts.
8.
Remove the rear seat on the vehicle.
9.
Remove the bolts, and then remove the rear seat frame (RH/LH).
INSTALLATION
Install in the reverse order of removal.
1.
Leg cover
2.
Seat outer side cover
3.
Headrest
4.
Headrest holder (free)
5.
Headrest holder (locked)
6.
Seatback board
7.
Armrest outer cover
8.
Armrest outer bracket
9.
Armrest inner cover
10. Armrest trim and pad
11. Armrest inner bracket
12.
Reclining device outer cover
13. Reclining device
14. Reclining device inner cover
15.
Seat back pad
16. Seat back trim
17. Seat back frame
18.
Seat cushion pad
19. Seat cushion trim
20. Seat cushion outer cover
21. Seat cushion inner cover
22. Rear seat frame (RH)
23. Rear seat bracket (RH)
24.
Seat cushion center bracket (LH seat
RH seat sharing)
25.
Seat cushion center bracket cover
(LH seat RH seat sharing)
PIIA4450E
PIIB1584E
PIIB1585E
REAR SEAT
SE-115
C
D
E
F
G
H
J
K
L
M
A
B
SE
Revision: 2005 August
2005 Murano
REMOVAL OF REMOTE CONTROL LEVER
1.
Remove the rear seat. Refer to
2.
Remove the luggage side finisher lower. Refer to
EI-38, "Removal and Installation"
.
3.
Remove the remote control lever mounting bolt.
4.
Remove the remote control lever assembly.
INSTALLATION OF REMOTE CONTROL LEVER
Install in the reverse order of removal.
PIIB1586E
1.
Remote control wire
2.
Bolt
3.
Remote control lever
SE-116
REAR SEAT
Revision: 2005 August
2005 Murano
SRS-1
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
H RESTRAINTS
CONTENTS
C
D
E
F
G
I
J
K
L
M
SECTION
SRS
A
B
SRS
Revision: 2005 August
2005 Murano
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
PRECAUTIONS . . . . . . . . . . . . . . .. 3
PREPARATION . . . . . . . . . . . . . . ... 4
Commercial Service Tools . . . . . . . . . . 4
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) . ... 5
TROUBLE DIAGNOSIS . . . . . . . . . . . .. 7
Trouble Diagnosis Introduction . . . . . . . . . 7
Self-Diagnosis Function (Without CONSULT-II) . . 16
SRS Operation Check . . . . . . . . . . . 17
DIAGNOSTIC PROCEDURE 1 . . . . . . ... 17
Trouble Diagnosis with CONSULT-II . . . . . .. 19
DIAGNOSTIC PROCEDURE 2 . . . . . . ... 19
DIAGNOSTIC PROCEDURE 3 . . . . . . ... 23
Trouble Diagnosis without CONSULT-II . . . . . 29
DIAGNOSTIC PROCEDURE 6 . . . . . . ... 29
WARNING LAMP FLASH CODE CHART . . ... 30
Trouble Diagnosis: “AIR BAG” Warning Lamp Does
Not Turn OFF . . . . . . . . . . . . . . . 34
DIAGNOSTIC PROCEDURE 7 . . . . . . ... 34
Trouble Diagnosis: “AIR BAG” Warning Lamp Does
Not Turn ON . . . . . . . . . . . . . . ... 35
DIAGNOSTIC PROCEDURE 8 . . . . . . ... 35
DRIVER AIR BAG MODULE . . . . . . . . . 36
Removal and Installation . . . . . . . . . . 36
REMOVAL . . . . . . . . . . . . . . ... 36
INSTALLATION . . . . . . . . . . . . ... 37
SPIRAL CABLE . . . . . . . . . . . . . . 38
Removal and Installation . . . . . . . . . . 38
REMOVAL . . . . . . . . . . . . . . ... 38
INSTALLATION . . . . . . . . . . . . ... 39
FRONT PASSENGER AIR BAG MODULE . . . .. 40
Removal and Installation . . . . . . . . . . 40
REMOVAL . . . . . . . . . . . . . . ... 40
INSTALLATION . . . . . . . . . . . . ... 41
SIDE CURTAIN AIR BAG MODULE . . . . . . 42
Removal and Installation . . . . . . . . . . 42
REMOVAL . . . . . . . . . . . . . . ... 42
INSTALLATION . . . . . . . . . . . . ... 43
CRASH ZONE SENSOR . . . . . . . . . . ... 44
Removal and Installation . . . . . . . . . . 44
REMOVAL . . . . . . . . . . . . . . ... 44
INSTALLATION . . . . . . . . . . . . ... 44
SIDE AIR BAG (SATELLITE) SENSOR . . . . ... 45
Removal and Installation . . . . . . . . . . 45
REMOVAL . . . . . . . . . . . . . . ... 45
INSTALLATION . . . . . . . . . . . . ... 45
SRS-2
Revision: 2005 August
2005 Murano
DIAGNOSIS SENSOR UNIT . . . . . . . . . . 47
Removal and Installation . . . . . . . . . . 47
COLLISION DIAGNOSIS . . . . . . . . . . .. 48
For Frontal Collision . . . . . . . . . . . . 48
SRS INSPECTION (FOR FRONTAL COLLI-
SION) . . . . . . . . . . . . . . . . ...48
PRECAUTIONS
SRS-3
C
D
E
F
G
I
J
K
L
M
A
B
SRS
Revision: 2005 August
2005 Murano
PRECAUTIONS
PFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
AHS000V2
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
●
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
●
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
●
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
AHS000V3
●
Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
●
Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 min-
utes.
For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt
pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes
have passed.
●
Diagnosis sensor unit must always be installed with their arrow marks “
⇐
” pointing towards the front of the
vehicle for proper operation. Also check diagnosis sensor unit for cracks, deformities or rust before instal-
lation and replace as required.
●
The spiral cable must be aligned with the neutral position since its rotations are limited. Do not turn steer-
ing wheel and column after removal of steering gear.
●
Handle air bag module carefully. Always place driver and front passenger air bag modules with the pad
side facing upward and seat mounted front side air bag module standing with the stud bolt side facing
down.
●
Conduct self-diagnosis to check entire SRS for proper function after replacing any components.
●
After air bag inflates, the front instrument panel assembly should be replaced if damaged.
●
Always replace instrument panel pad following front passenger air bag deployment.
SRS-4
PREPARATION
Revision: 2005 August
2005 Murano
PREPARATION
PFP:00002
Commercial Service Tools
AHS000E4
Tool name
Description
Tamper resistant TORX bit
Size: T30
S-NT757
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
SRS-5
C
D
E
F
G
I
J
K
L
M
A
B
SRS
Revision: 2005 August
2005 Murano
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
PFP:28556
SRS Configuration
AHS000AM
The air bag deploys if the diagnosis sensor unit activates while the ignition switch is in the ON or START posi-
tion.
The collision modes for which supplemental restraint systems are activated are different among the SRS sys-
tems. For example, the driver air bag module and front passenger air bag module are activated in a frontal col-
lision but not in a side collision.
SRS configurations which are activated for some collision modes are as follows;
PHIA0698E
SRS configuration
Frontal collision
Left side collision
Right side collision
Driver air bag module
×
—
—
Front passenger air bag module
×
—
—
Front LH seat belt pre-tensioner
×
—
—
Front RH seat belt pre-tensioner
×
—
—
Front LH side air bag module
—
×
—
Front RH side air bag module
—
—
×
LH side curtain air bag module
—
×
—
RH side curtain air bag module
—
—
×
SRS-6
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
Revision: 2005 August
2005 Murano
Front Seat Belt Pre-tensioner with Load Limiter
AHS000AN
The seat belt pre-tensioner system with load limiter is installed for
both the driver's seat and the front passenger's seat. It operates
simultaneously with the SRS air bag system in the event of a frontal
collision with an impact exceeding a specified level.
When the frontal collision with an impact exceeding a specified level
occurs, seat belt slack resulting from clothing or other factors is
immediately taken up by the pre-tensioner. Vehicle passengers are
securely restrained.
When passengers in a vehicle are thrown forward in a collision and
the restraining force of the seat belt exceeds a specified level, the
load limiter permits the specified extension of the seat belt by the
twisting of the ELR shaft, and a relaxation of the chest-area seat belt
web tension while maintaining force.
Front Side Air Bag
AHS000AO
Front side air bag is built-in type.
The front seatbacks with built-in type side air bag have the labels as
shown.
Side Curtain Air Bag
AHS000AP
The side curtain air bags have the labels as shown.
SRS444
PHIA0249E
BF-2006D
TROUBLE DIAGNOSIS
SRS-7
C
D
E
F
G
I
J
K
L
M
A
B
SRS
Revision: 2005 August
2005 Murano
TROUBLE DIAGNOSIS
PFP:00004
Trouble Diagnosis Introduction
AHS000E5
CAUTION:
●
Do not use electrical test equipment on any circuit related to the SRS unless instructed in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
●
Do not repair, splice or modify the SRS wiring harness. If the harness is damaged, replace it with a
new one.
●
Keep ground portion clean.
DIAGNOSIS FUNCTION
The SRS self-diagnostic results can be read by using “AIR BAG” warning lamp and/or CONSULT-II.
The User mode is exclusively prepared for the customer (driver). This mode warns the driver of a system mal-
function through the operation of the “AIR BAG” warning lamp.
The Diagnosis mode allows the technician to locate and inspect the malfunctioning part.
The mode applications for the “AIR BAG” warning lamp and CONSULT-II are as follows:
HOW TO PERFORM TROUBLE DIAGNOSIS FOR QUICK AND ACCURATE REPAIR
A good understanding of the malfunction conditions can make troubleshooting faster and more accurate.
In general, each customer feels differently about a malfunction. It is important to fully understand the symp-
toms or conditions for a customer complaint.
Information from Customer
WHAT. . Vehicle model
WHEN. . Date, Frequencies
WHERE. . Road conditions
HOW. . Operating conditions, Symptoms
Preliminary Check
Make sure the following parts are in good order.
●
Battery (Refer to
.)
●
Fuse (Refer to
SRS-11, "Wiring Diagram — SRS —"
●
System component-to-harness connections
User mode
Diagnosis mode
Display type
“AIR BAG” warning lamp
X
X
ON-OFF operation
CONSULT-II
—
X
Monitoring
SRS-8
TROUBLE DIAGNOSIS
Revision: 2005 August
2005 Murano
WORK FLOW
*1:
*2:
*3:
SRS-19, "DIAGNOSTIC PROCE-
DURE 2"
*4:
SRS-29, "DIAGNOSTIC PROCE-
DURE 6"
*5:
SRS-23, "DIAGNOSTIC PROCE-
DURE 3"
.
*6:
SRS-29, "DIAGNOSTIC PROCE-
DURE 6"
PHIA0217E
TROUBLE DIAGNOSIS
SRS-9
C
D
E
F
G
I
J
K
L
M
A
B
SRS
Revision: 2005 August
2005 Murano
Component Parts Location
AHS000E6
PHIA0273E
SRS-10
TROUBLE DIAGNOSIS
Revision: 2005 August
2005 Murano
Schematic
AHS000E7
THWA0020E
TROUBLE DIAGNOSIS
SRS-11
C
D
E
F
G
I
J
K
L
M
A
B
SRS
Revision: 2005 August
2005 Murano
Wiring Diagram — SRS —
AHS000E8
THWA0025E
SRS-12
TROUBLE DIAGNOSIS
Revision: 2005 August
2005 Murano
THWA0022E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст