Nissan Murano Z50 (2005 year). Manual — part 186
PARKING, LICENSE PLATE AND TAIL LAMPS
LT-163
C
D
E
F
G
H
I
J
L
M
A
B
LT
Revision: 2005 August
2005 Murano
Preliminary Check
AKS00ALU
CHECK POWER SUPPLY AND GROUND CIRCUIT
1.
CHECK FUSES
●
Check for blown fuses.
Refer to
LT-157, "Wiring Diagram — TAIL/L —"
OK or NG
OK
>> GO TO 2.
NG
>> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. Refer to
3, "POWER SUPPLY ROUTING CIRCUIT"
.
2.
CHECK POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check voltage between BCM harness connector and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Check harness for open or short between BCM and
fuse.
3.
CHECK GROUND CIRCUIT
Check continuity between BCM harness connector and ground.
OK or NG
OK
>> INSPECTION END
NG
>> Check ground circuit harness.
Unit
Power source
Fuse and fusible link No.
BCM
Battery
F
18
Ignition switch ON or START position
1
Ignition switch ACC or ON position
6
IPDM E/R
Battery
71
Terminal
Ignition switch position
(+)
(-)
OFF
ACC
ON
Connector
Terminal
(Wire color)
M34
11 (P/B)
Ground
Approx. 0V
Battery
voltage
Battery
voltage
38 (R)
Approx. 0V
Approx. 0V
Battery
voltage
M35
42 (GR)
Battery
voltage
Battery
voltage
Battery
voltage
55 (W/B)
Battery
voltage
Battery
voltage
Battery
voltage
PKIB5197E
Terminal
Continuity
Connector
Terminal (Wire color)
Ground
M35
52 (B)
Yes
PKIB5198E
LT-164
PARKING, LICENSE PLATE AND TAIL LAMPS
Revision: 2005 August
2005 Murano
CONSULT-II Functions (BCM)
AKS00ALV
Refer to
LT-17, "CONSULT-II Functions (BCM)"
in HEADLAMP - XENON TYPE.
Refer to
LT-50, "CONSULT-II Functions (BCM)"
in HEADLAMP - CONVENTIONAL TYPE.
CONSULT-II Functions (IPDM E/R)
AKS00CRH
Refer to
LT-20, "CONSULT-II Functions (IPDM E/R)"
in HEADLAMP - XENON TYPE.
Refer to
LT-53, "CONSULT-II Functions (IPDM E/R)"
in HEADLAMP - CONVENTIONAL TYPE.
Parking, License Plate and Tail Lamps Do Not Illuminate
AKS00ALW
1.
CHECK COMBINATION SWITCH INPUT SIGNAL
With CONSULT-II
Select “BCM” on CONSULT-II. With “HEAD LAMP” data monitor,
make sure “LIGHT SW 1ST” turns ON-OFF linked with operation of
lighting switch.
Without CONSULT-II
Refer to
LT-145, "Combination Switch Inspection"
OK or NG
OK
>> GO TO 2.
NG
>> Check combination switch (lighting switch). Refer to
145, "Combination Switch Inspection"
.
2.
ACTIVE TEST
With CONSULT-II
1.
Select “IPDM E/R” on CONSULT-II, and select “ACTIVE TEST”
on “SELECT DIAG MODE” screen.
2.
Select “TAIL LAMP” on “SELECT TEST ITEM” screen.
3.
Touch “ON” screen.
4.
Make sure parking, license plate, side marker and tail lamps
operate.
Without CONSULT-II
1.
Start auto active test. Refer to
2.
Make sure parking, license plate, side marker and tail lamps operate.
OK or NG
OK
>> GO TO 3.
NG
>> GO TO 4.
When lighting switch is 1ST
position
: LIGHT SW 1 ST ON
PKIA7607E
Parking, license plate, side marker and tail lamp
should operate.
Parking, license plate, side marker and tail lamp
should operate.
SKIA5957E
PARKING, LICENSE PLATE AND TAIL LAMPS
LT-165
C
D
E
F
G
H
I
J
L
M
A
B
LT
Revision: 2005 August
2005 Murano
3.
CHECK IPDM E/R
1.
Select “IPDM E/R” on CONSULT-II, and select “DATA MONI-
TOR” on “SELECT DIAG MODE” screen.
2.
Make sure “TAIL & CLR REQ” turns ON when lighting switch is
in 1ST position.
OK or NG
OK
>> Replace IPDM E/R.
NG
>> Replace BCM. Refer to
BCS-16, "Removal and Installa-
When lighting switch is 1ST
position
: TAIL & CLR REQ ON
SKIA5958E
LT-166
PARKING, LICENSE PLATE AND TAIL LAMPS
Revision: 2005 August
2005 Murano
4.
CHECK INPUT SIGNAL
With CONSULT-II
1.
Turn ignition switch OFF.
2.
Disconnect front combination lamp RH and LH, license plate lamp RH and LH and rear combination lamp
RH and LH connectors.
3.
Select “IPDM E/R” on CONSULT-II, and select “ACTIVE TEST” on “SELECT DIAG MODE” screen.
4.
Select “TAIL LAMP” on “SELECT TEST ITEM” screen.
5.
Touch “ON” screen.
6.
When tail lamp is operating, check voltage between front combination lamp, license plate lamp, rear com-
bination lamp harness connector and ground.
Without CONSULT-II
1.
Turn ignition switch OFF.
2.
Disconnect front combination lamp RH and LH, license plate lamp RH and LH and rear combination lamp
RH and LH connectors.
3.
Start auto active test. Refer to
4.
Check voltage between front combination lamp harness connector and ground.
5.
Check voltage between license plate lamp harness connector and ground.
6.
Check voltage between rear combination lamp harness connector and ground.
OK or NG
OK
>> GO TO 6.
NG
>> GO TO 5.
Terminal
Voltage
Front combination lamp (+)
(Parking)
(-)
Connector
Terminal (Wire color)
RH
E30
7 (R/L)
Ground Battery
voltage
LH
E17
7 (L/Y)
PKIA4917E
Terminal
Voltage
License plate lamp (+)
(-)
Connector
Terminal (Wire color)
RH
D104
1 (R/L)
Ground
Battery voltage
LH
D102
PKIB2156E
Terminal
Voltage
Rear combination lamp (+)
(Tail and side marker)
(-)
Connector
Terminal (Wire color)
RH
B29
1 (R/L)
Ground
Battery voltage
LH
B24
SKIA5962E
PARKING, LICENSE PLATE AND TAIL LAMPS
LT-167
C
D
E
F
G
H
I
J
L
M
A
B
LT
Revision: 2005 August
2005 Murano
5.
CHECK PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMP CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and
front combination lamp harness connector.
4.
Check continuity between IPDM E/R harness connector and
license plate lamp harness connector.
5.
Check continuity between IPDM E/R harness connector and
rear combination lamp harness connector.
OK or NG
OK
>> Replace IPDM E/R.
NG
>> Repair harness or connector.
Terminal
Continuity
IPDM E/R
Front combination lamp
(Parking)
Connector
Terminal
(Wire color)
Connector
Terminal
(Wire color)
E7
22 (L/Y)
RH
E30
7 (R/L)
Yes
LH
E17
7 (L/Y)
PKIA4919E
Terminal
Continuity
IPDM E/R
License plate lamp
Connector
Terminal
(Wire color)
Connector
Terminal
(Wire color)
E7
22 (L/Y)
RH
D104
1 (R/L)
Yes
LH
D102
PKIB2157E
Terminal
Continuity
IPDM E/R
Rear combination lamp
(Tail and side marker)
Connector
Terminal
(Wire color)
Connector
Terminal
(Wire color)
E7
22 (L/Y)
RH
B29
1 (R/L)
Yes
LH
B24
SKIA5966E
LT-168
PARKING, LICENSE PLATE AND TAIL LAMPS
Revision: 2005 August
2005 Murano
6.
CHECK GROUND
1.
Check continuity between front combination lamp harness con-
nector and ground.
2.
Check continuity between license plate lamp harness connector
and ground.
3.
Check continuity between rear combination lamp harness con-
nector and ground.
OK or NG
OK
>> Check bulbs.
NG
>> Repair harness or connector.
Parking, License Plate and Tail Lamps Do Not Turn OFF (After Approx. 10 Min-
utes)
AKS00ALX
1.
CHECK IPDM E/R
1.
Turn the ignition switch ON. Place the combination switch (lighting switch) in the ON position. Turn the
ignition switch OFF.
2.
Make sure the parking, license plate, and tail lamps turn OFF after approximately 10 minutes.
OK or NG
OK
>> INSPECTION END
NG
>> Ignition relay malfunction. Refer to
PG-18, "Function of Detecting Ignition Relay Malfunction"
Terminal
Continuity
Front combination lamp
(Parking)
Ground
Connector
Terminal (Wire color)
RH
E30
5 (B/W)
Yes
LH
E17
PKIA6328E
Terminal
Continuity
License plate lamp
Ground
Connector
Terminal (Wire color)
RH
D104
2 (B)
Yes
LH
D102
PKIB2160E
Terminal
Continuity
Rear combination lamp
(Tail and side marker)
Ground
Connector
Terminal (Wire color)
RH
B29
4 (B)
Yes
LH
B24
PKIA6363E
PARKING, LICENSE PLATE AND TAIL LAMPS
LT-169
C
D
E
F
G
H
I
J
L
M
A
B
LT
Revision: 2005 August
2005 Murano
Bulb Replacement
AKS00ALY
LICENSE PLATE LAMP
1.
Remove back door inner finisher. Refer to
in “EI” section.
2.
Disconnect the license plate lamp connector.
3.
Turn bulb socket counterclockwise and unlock it.
4.
Remove bulb from its socket.
5.
Installation is the reverse order of removal.
PARKING LAMP (CLEARANCE LAMP)
For bulb replacement, refer to
in “HEADLAMP” (XENON TYPE).
For bulb replacement, refer to
in “HEADLAMP” (CONVENTIONAL TYPE).
TAIL LAMP
For bulb replacement, refer to
in “REAR COMBINATION LAMP”.
FRONT SIDE MARKER LAMP
For bulb replacement, refer to
in “HEADLAMP” (XENON TYPE).
For bulb replacement, refer to
in “HEADLAMP” (CONVENTIONAL TYPE).
REAR SIDE MARKER LAMP
For bulb replacement, refer to
in “REAR COMBINATION LAMP”.
Removal and Installation
AKS00ALZ
LICENSE PLATE LAMP
1.
Remove back door inner finisher. Refer to
in “EI” section.
2.
Remove rear wiper motor. Refer to
Installation of Rear Wiper Motor"
3.
Remove the license plate lamp mounting screws and remove it.
4.
Installation is the reverse order of removal.
PARKING LAMP (CLEARANCE LAMP)
For parking lamp (clearance lamp) removal and installation procedures, refer to
in “HEADLAMP” (XENON TYPE).
For parking lamp (clearance lamp) removal and installation procedures, refer to
in “HEADLAMP” (CONVENTIONAL TYPE).
TAIL LAMP
For tail lamp removal and installation procedures, refer to
LT-170, "Removal and Installation"
in “REAR COM-
BINATION LAMP”.
FRONT SIDE MARKER LAMP
For headlamp removal and installation procedures, refer to
LT-37, "Removal and Installation"
in “HEALAMP”
(XENON TYPE).
For headlamp removal and installation procedures, refer to
LT-67, "Removal and Installation"
in “HEALAMP”
(CONVENTIONAL TYPE).
REAR SIDE MARKER LAMP
For rear side marker lamp removal and installation procedures, refer to
LT-170, "Removal and Installation"
“REAR COMBINATION LAMP”.
License plate lamp
: 12V - 5W
PKIA2531E
PKIB2161E
LT-170
REAR COMBINATION LAMP
Revision: 2005 August
2005 Murano
REAR COMBINATION LAMP
PFP:26554
Bulb Replacement
AKS005M1
STOP & TAIL LAMP BULB, REAR SIDE MARKER LAMP BULB, REAR TURN SIGNAL LAMP
BULB
1.
Remove rear combination lamp. Refer to
2.
Turn bulb socket counterclockwise and unlock it.
3.
Remove bulb.
4.
Installation is the reverse order of removal.
Removal and Installation
AKS005M2
REMOVAL
1.
Remove rear combination lamp finisher.
2.
Remove rear combination lamp mounting bolts.
3.
Pull the rear combination lamp toward side of the vehicle and
remove from the vehicle.
4.
Disconnect rear combination lamp connector.
INSTALLATION
Installation is the reverse order of removal.
Stop/tail lamp
: 12V - 21/5W
Rear side marker lamp
: 12V - 5W
Rear turn signal lamp
: 12V - 21W
PKIA2532E
PKIA2533E
Rear combination lamp mounting bolt
: 5.5 N·m (0.56 kg-m, 49 in-lb)
VANITY MIRROR LAMP
LT-171
C
D
E
F
G
H
I
J
L
M
A
B
LT
Revision: 2005 August
2005 Murano
VANITY MIRROR LAMP
PFP:96400
Bulb Replacement
AKS005M3
Wiring diagram. Refer to
LT-182, "Wiring Diagram — ROOM/L —"
.
1.
Insert a thin screwdriver in the notch and remove lens.
2.
Remove bulb.
3.
Installation is the reverse order of removal.
Vanity mirror lamp
: 12V - 2W
PKIB2178E
LT-172
MAP LAMP
Revision: 2005 August
2005 Murano
MAP LAMP
PFP:26430
Bulb Replacement
AKS005M4
LT-182, "Wiring Diagram — ROOM/L —"
.
1.
Disconnect the battery negative cable.
2.
Remove the lens using clip driver or suitable tool.
3.
Remove the bulb.
4.
Installation is the reverse order of removal.
Removal and Installation
AKS005M5
REMOVAL
1.
Pull wider part of thin plate of the map lamp to disengage the
metal clip.
2.
Pull map lamp in direction shown by the arrow in the figure.
3.
Disconnect map lamp connector and remove the map lamp.
INSTALLATION
Installation is the reverse order of removal.
Map lamp
: 12V - 8 W
PKIA2534E
PKIA2520E
PERSONAL LAMP
LT-173
C
D
E
F
G
H
I
J
L
M
A
B
LT
Revision: 2005 August
2005 Murano
PERSONAL LAMP
PFP:26415
Bulb Replacement, Removal and Installation
AKS004LW
Wiring diagram. Refer to
LT-182, "Wiring Diagram — ROOM/L —"
.
1.
Insert a clip driver or suitable tool and disengage the metal clip
fittings of the personal lamp.
2.
Disconnect personal lamp connector and remove the personal
lamp.
3.
Remove the housing mounting screws, and separate it.
4.
Remove bulb from the base.
5.
Installation is the reverse order of removal.
PKIA2540E
Personal lamp
: 12V - 8W
PKIA2536E
LT-174
LUGGAGE ROOM LAMP
Revision: 2005 August
2005 Murano
LUGGAGE ROOM LAMP
PFP:26410
Bulb Replacement, Removal and Installation
AKS005M6
LT-182, "Wiring Diagram — ROOM/L —"
.
1.
Insert a screwdriver as shown in the figure and pull out the lug-
gage room lamp.
2.
Disconnect the luggage room lamp connector.
3.
Remove the bulb.
4.
Installation is the reverse order of removal.
PKIA1884E
PKIA2541E
Luggage room lamp
: 12V - 8W
PKIA2537E
INTERIOR ROOM LAMP
LT-175
C
D
E
F
G
H
I
J
L
M
A
B
LT
Revision: 2005 August
2005 Murano
INTERIOR ROOM LAMP
PFP:26410
Component Parts and Harness Connector Location
AKS00AME
System Description
AKS005R0
When the room lamp and personal lamp switch is in DOOR position, room lamp and personal lamp ON/OFF is
controlled by timer according to signals from switches including key switch, front door switch driver side,
unlock signal from key fob, door lock and unlock switch, key cylinder lock and unlock switch, ignition switch.
When the room lamp and personal lamp turns ON, there is a gradual brightening over 1 second. When room
lamp and personal lamp turns OFF, there is a gradual dimming over 1 second.
The room lamp and personal lamp timer is controlled by the BCM (body control module).
Room lamp and personal lamp timer control settings can be changed with CONSULT-II.
Ignition key hole illumination turns ON at time when driver door is opened (door switch ON) or removed key
fob from key cylinder. Illumination turns OFF when driver door is closed (door switch OFF).
Step lamp turns ON at time when driver door or passenger door is opened (door switch ON). Lamp turns OFF
when driver, passenger doors are closed (all door switches OFF).
PKIB2179E
LT-176
INTERIOR ROOM LAMP
Revision: 2005 August
2005 Murano
POWER SUPPLY AND GROUND
Power is supplied at all times (without Intelligent Key system)
●
through 10A fuse [No. 21, located in fuse block (J/B)]
●
to key switch terminal 3,
●
through 50A fusible link (letter F, located in fuse and fusible link block)
●
to BCM terminal 55.
Power is supplied at all times (with Intelligent Key system)
●
through 10A fuse [No.22, located in fuse block (J/B)]
●
to key switch and ignition knob switch terminals 1 and 3,
●
through 10A fuse [No. 18, located in fuse block (J/B)]
●
to BCM terminal 42,
●
through 50A fusible link (letter F, located in fuse and fusible link block)
●
to BCM terminal 55.
When the key is inserted to ignition key cylinder, power is interrupted (without Intelligent Key system)
●
through key switch terminal 4
●
to BCM terminal 37.
When inserted key plate to key switch and ignition knob switch, power is supplied (with Intelligent Key system)
●
through key switch and ignition knob switch terminal 4
●
to BCM terminal 37.
When pushed key switch and ignition knob switch, power is supplied (with Intelligent Key system)
●
through key switch and ignition knob switch terminal 2
●
to intelligent key unit terminal 27.
With the ignition switch in the ON or START position, power is supplied
●
through 10A fuse [No. 1, located in fuse block (J/B)]
●
to BCM terminal 38.
Ground is supplied
●
to BCM terminal 52
●
through grounds E13, E26 and E28.
When the driver side door is opened, ground is supplied
●
to BCM terminal 62
●
through front door lock assembly (driver side) (door switch) terminal 4
●
through front door lock assembly (driver side) (door switch) terminal 5
●
through grounds M14 and M78.
When the passenger side door is opened, ground is supplied
●
to BCM terminal 12
●
through front door lock assembly (passenger side) (door switch) terminal 4
●
through front door lock assembly (passenger side) (door switch) terminal 5
●
through grounds M14 and M78.
When the rear door LH is opened, ground is supplied
●
to BCM terminal 63
●
through rear door lock assembly LH (door switch) terminal 4
●
through rear door lock assembly LH (door switch) terminal 5
●
through grounds B7 and B20.
When the rear door RH is opened, ground is supplied
●
to BCM terminal 13
●
through rear door lock assembly RH (door switch) terminal 4
●
through rear door lock assembly RH (door switch) terminal 5
●
through grounds B105 and B116.
When the driver side door is unlocked by the door lock and unlock switch, BCM receives a ground signal
INTERIOR ROOM LAMP
LT-177
C
D
E
F
G
H
I
J
L
M
A
B
LT
Revision: 2005 August
2005 Murano
●
through grounds M14 and M78
●
to power window main switch (door lock and unlock switch) terminal 17 or front power window switch
(passenger side) (door lock and unlock switch) terminal 11
●
from power window main switch (door lock and unlock switch) terminal 14 or front power window switch
(passenger side) (door lock and unlock switch) terminal 16
●
to BCM terminal 22.
When the front driver side door is unlocked by the driver side door lock assembly (door key cylinder switch),
BCM receives a ground signal
●
through grounds M14 and M78
●
to front door lock assembly (driver side) (door key cylinder switch) terminal 5 (without Intelligent Key sys-
tem)
●
to door key cylinder switch terminal 2 (with Intelligent Key system)
●
from front door lock assembly (driver side) (door key cylinder switch) terminal 6 (without Intelligent Key
system)
●
from door key cylinder switch terminal 3 (with Intelligent Key system)
●
to power window main switch (door lock and unlock switch) terminal 6
●
from power window main switch (door lock and unlock switch) terminal 14
●
to BCM terminal 22.
When a signal, or combination of signals is received by BCM, ground is supplied
●
to room lamp terminal 1 and
●
to personal lamp LH and RH terminal 3
●
through BCM terminal 48.
With power and supplied, the interior lamp illuminates.
SWITCH OPERATION
When driver door switch is ON (door is opened), ground is supplied
●
to ignition key hole illumination terminal 2
●
through BCM terminal 1.
And power is supplied
●
from BCM terminal 41
●
to ignition key hole illumination terminal 1.
When any door switch is ON (door is opened), ground is supplied
●
through BCM terminal 47
●
to step lamp (driver side and passenger side) terminal 2.
And power is supplied
●
from BCM terminal 41
●
to step lamp (driver side and passenger side) terminal 1.
When map lamp switch is ON, ground is supplied
●
to map lamp terminal 2
●
through grounds M14 and M78.
And power is supplied
●
from BCM terminal 41
●
to map lamp terminal 1.
When vanity mirror lamp (driver side and passenger side) is ON, ground is supplied
●
to vanity mirror lamp (driver side and passenger side) terminal 2
●
through grounds M14 and M78.
And power is supplied
●
from BCM terminal 41
●
to vanity mirror lamp (driver side and passenger side) terminal 1.
When personal lamp LH and RH switch is ON, ground is supplied
LT-178
INTERIOR ROOM LAMP
Revision: 2005 August
2005 Murano
●
to personal lamp LH and RH terminal 2
●
through grounds M14 and M78.
And power is supplied
●
from BCM terminal 41
●
to personal lamp LH and RH terminal 1.
When room lamp switch is ON, ground is supplied
●
to room lamp terminal 3
●
through grounds M14 and M78.
And power is supplied
●
from BCM terminal 41
●
to room lamp terminal 2.
When luggage room lamp RH and LH is ON, and then back door switch is ON, ground is supplied
●
to luggage room lamp RH and LH terminal 2
●
through back door switch terminal 3
●
through back door switch terminal 4
●
through grounds B7 and B20.
And power is supplied
●
from BCM terminal 41
●
to luggage room lamp RH and LH terminal 1.
ROOM LAMP TIMER OPERATION
Without Intelligent Key System
When room lamp and personal lamp switch is in DOOR position, and when all conditions below are met, BCM
performs timer control (maximum 30 seconds) for room lamp and personal lamp ON/OFF.
In addition, when spot turns ON or OFF there is gradual brightening or dimming over 1 second.
Power is supplied
●
through 10A fuse [No. 21, located in the fuse block (J/B)]
●
to key switch terminal 3.
Key is removed from ignition key cylinder (key switch OFF), power will not be supplied to BCM terminal 37.
Ground is supplied
●
from BCM terminal 22
●
to power window main switch (door lock and unlock switch) terminal 14.
At this time, BCM detects that driver door is unlocked. It determines that room lamp and personal lamp timer
operation conditions are met, and turns the room lamp and personal lamp ON for 30 seconds.
Key is in ignition key cylinder (key switch ON),
Power is supplied
●
through key switch terminal 4
●
to BCM terminal 37.
When key is removed from key switch (key switch OFF), power supply to BCM terminal 37 is terminated. BCM
detects that key has been removed, determines that room lamp and personal lamp timer conditions are met,
and turns the room lamp and personal lamp ON for 30 seconds.
When driver door opens
→
closes, and the key is not inserted in the key switch and key lock solenoid (key
switch OFF), BCM terminal 62 changes between 0V (door open)
→
12V (door closed). The BCM determines
that conditions for room lamp and personal lamp operation are met and turns the interior lamp ON for 30 sec-
onds.
Timer control is canceled under the following conditions.
●
Driver door is locked [when locked key fob or power window main switch (door lock and unlock switch),
door key cylinder switch]
●
Driver door is opened (driver door switch turns ON)
●
Ignition switch ON.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст