Nissan Murano Z50 (2005 year). Manual — part 129
TIMING CHAIN
EM-77
C
D
E
F
G
H
I
J
K
L
M
A
EM
Revision: 2005 August
2005 Murano
b.
Apply a continuous bead of liquid gasket with the tube presser
[SST: WS39930000 (
—
)] to intake valve timing control cov-
ers as shown in the figure.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-47, "RECOMMENDED CHEMICAL PRODUCTS AND
SEALANTS"
.
c.
Install new collared O-rings in front timing chain case oil hole
(left and right sides).
d.
Being careful not to move seal rings from the installation grooves, align dowel pins on front timing chain
case with the holes to install intake valve timing control covers.
e.
Tighten mounting bolts in numerical order as shown in the fig-
ure.
16. Install crankshaft pulley as follows:
a.
Install crankshaft pulley, taking care not to damage front oil seal.
●
When press-fitting crankshaft pulley with a plastic hammer, tap on its center portion (not circumfer-
ence).
b.
Fix crankshaft with the pulley holder [SST: KV10109300 (
—
)].
c.
Tighten crankshaft pulley bolt.
d.
Turn crankshaft pulley bolt 90 degrees clockwise (angle tighten-
ing).
CAUTION:
Check the tightening angle by using the angle wrench
[SST]. Avoid judgement by visual inspection without SST.
●
Check tightening angle indicated on the angle wrench indica-
tor plate.
SBIA0492E
PBIC2631E
PBIC0918E
: 44.1 N·m (4.5 kg-m, 33 ft-lb)
PBIC4224E
EM-78
TIMING CHAIN
Revision: 2005 August
2005 Murano
17. Rotate crankshaft pulley in normal direction (clockwise when viewed from engine front) to confirm it turns
smoothly.
18. Install in the reverse order of removal after this step.
INSPECTION AFTER INSTALLATION
Inspection for Leaks
The following are procedures for checking fluids leak, lubricates leak and exhaust gases leak.
●
Before starting engine, check oil/fluid levels including engine coolant and engine oil. If less than required
quantity, fill to the specified level. Refer to
MA-10, "RECOMMENDED FLUIDS AND LUBRICANTS"
●
Use procedure below to check for fuel leakage.
–
Turn ignition switch “ON” (with engine stopped). With fuel pressure applied to fuel piping, check for fuel
leakage at connection points.
–
Start engine. With engine speed increased, check again for fuel leakage at connection points.
●
Run engine to check for unusual noise and vibration.
NOTE:
If hydraulic pressure inside timing chain tensioner drops after removal/installation, slack in the guide may
generate a pounding noise during and just after engine start. However, this is normal. Noise will stop after
hydraulic pressure rises.
●
Warm up engine thoroughly to make sure there is no leakage of fuel, exhaust gases, or any oil/fluids
including engine oil and engine coolant.
●
Bleed air from lines and hoses of applicable lines, such as in cooling system.
●
After cooling down engine, again check oil/fluid levels including engine oil and engine coolant. Refill to the
specified level, if necessary.
Summary of the inspection items:
* Transmission/transaxle/CVT fluid. power steering fluid, brake fluid, etc.
Item
Before starting engine
Engine running
After engine stopped
Engine coolant
Level
Leakage
Level
Engine oil
Level
Leakage
Level
Other oils and fluid*
Level
Leakage
Level
Fuel
Leakage
Leakage
Leakage
Exhaust gases
—
Leakage
—
CAMSHAFT
EM-79
C
D
E
F
G
H
I
J
K
L
M
A
EM
Revision: 2005 August
2005 Murano
CAMSHAFT
PFP:13001
Removal and Installation
ABS0032R
REMOVAL
1.
Remove engine assembly from the vehicle, and separate front suspension member, transaxle and trans-
fer (AWD models) assembly from engine. Refer to
.
1.
Intake valve timing control solenoid
valve
2.
Gasket
3.
Camshaft bracket (No. 2 to No. 4)
4.
Seal washer
5.
Camshaft (EXH)
6.
Camshaft (INT)
7.
Camshaft bracket (No. 1)
8.
Dowel pin
9.
Valve lifter
10. O-ring
11.
Timing chain tensioner (Secondary)
12. Spring
13. Plunger
14.
Cylinder head (right bank)
15. Cylinder head (left bank)
16. O-ring
17.
Camshaft position sensor (PHASE)
(right bank)
18.
Camshaft position sensor (PHASE)
(left bank)
PBIC2306E
EM-80
CAMSHAFT
Revision: 2005 August
2005 Murano
2.
Install engine sub-attachment with engine stand shaft [SST: KV10117001 (
—
) and KV10106500 (
—
)] to right side of cylinder block, then lift engine, and mount it onto engine stand [SST: ST0501S000
(
—
)]. Refer to
3.
Remove front timing chain case, camshaft sprocket, timing chain and rear timing chain case. Refer to
.
4.
Remove camshaft position sensor (PHASE) (right and left
banks) from cylinder head back side.
CAUTION:
●
Handle carefully to avoid dropping and shocks.
●
Do not disassemble.
●
Do not allow metal powder to adhere to magnetic part at
sensor tip.
●
Do not place sensors in a location where they are
exposed to magnetism.
5.
Remove intake valve timing control solenoid valves.
●
Discard intake valve timing control solenoid valve gaskets and
use new gaskets for installation.
6.
Remove camshaft brackets.
●
Mark camshafts, camshaft brackets and bolts so they are placed in the same position and direction for
installation.
●
Equally loosen camshaft bracket bolts in several steps in
reverse order as shown in the figure.
7.
Remove camshafts.
8.
Remove valve lifters.
KBIA1046E
SEM443GA
PBIC2050E
CAMSHAFT
EM-81
C
D
E
F
G
H
I
J
K
L
M
A
EM
Revision: 2005 August
2005 Murano
●
Identify installation positions, and store them without mixing them up.
9.
Remove chain tensioner (secondary) from cylinder head.
●
Remove timing chain tensioner (secondary) with its stopper
pin attached.
NOTE:
Stopper pin was attached when timing chain (secondary) was
removed.
INSPECTION AFTER REMOVAL
Camshaft Runout
1.
Put V-block on precise flat table, and support No. 2 and 4 jour-
nals of camshaft.
CAUTION:
Do not support journal No. 1 (on the side of camshaft
sprocket) because it has a different diameter from the other
three locations.
2.
Set a dial indicator vertically to No. 3 journal.
3.
Turn camshaft to one direction with hands, and measure the
camshaft runout on dial indicator. (Total indicator reading)
4.
If it exceeds the limit, replace camshaft.
Camshaft Cam Height
1.
Measure the camshaft cam height with a micrometer.
2.
If wear is beyond the limit, replace camshaft.
Camshaft Journal Oil Clearance
CAMSHAFT JOURNAL DIAMETER
●
Measure the outer diameter of camshaft journal with a microme-
ter.
SEM947G
Standard
: Less than 0.02 mm (0.001 in)
Limit
: 0.05 mm (0.002 in)
PBIC0929E
Standard cam height (intake and exhaust)
: 44.865 - 45.055 mm (1.7663 - 1.7738 in)
Cam wear limit
: 0.2 mm (0.008 in)
EMQ0072D
Standard:
No. 1
: 25.935 - 25.955 mm (1.0211 - 1.0218 in)
No. 2, 3, 4
: 23.445 - 23.465 mm (0.9230 - 0.9238 in)
PBIC0040E
EM-82
CAMSHAFT
Revision: 2005 August
2005 Murano
CAMSHAFT BRACKET INNER DIAMETER
●
Tighten camshaft bracket bolt with the specified torque. Refer to
for the tighten-
ing procedure.
●
Measure inner diameter “A” of camshaft bracket with a bore
gauge.
CAMSHAFT JOURNAL OIL CLEARANCE
●
(Oil clearance) = (Camshaft bracket inner diameter) – (Camshaft journal diameter).
●
If the calculated value exceeds the limit, replace either or both camshaft and cylinder head.
NOTE:
Camshaft brackets cannot be replaced as single part, because there are machined together with cylinder
head. Replace whole cylinder head assembly.
Camshaft End Play
●
Install a dial indicator in thrust direction on front end of camshaft.
Measure the end play of dial indicator when camshaft is moved
forward/backward (in direction to axis).
●
Measure the following parts if out of the limit.
–
Dimension “A” for camshaft No. 1 journal
–
Dimension “B” for cylinder head No. 1 journal bearing
●
Refer to the standards above, and then replace camshaft and/or
cylinder head.
Camshaft Sprocket Runout
1.
Put V-block on precise flat table, and support No. 2 and 4 journal of camshaft.
CAUTION:
Do not support journal No. 1 (on the side of camshaft sprocket) because it has a different diameter
from the other three locations.
Standard:
No. 1
: 26.000 - 26.021 mm (1.0236 - 1.0244 in)
No. 2, 3, 4
: 23.500 - 23.521 mm (0.9252 - 0.9260 in)
PBIC1645E
Standard:
No. 1
: 0.045 - 0.086 mm (0.0018 - 0.0034 in)
No. 2, 3, 4
: 0.035 - 0.076 mm (0.0014 - 0.0030 in)
Limit
: 0.15 mm (0.0059 in)
Standard
: 0.115 - 0.188 mm (0.0045 - 0.0074 in)
Limit
: 0.24 mm (0.0094 in)
SEM864E
Standard
: 27.500 - 27.548 mm (1.0827 - 1.0846 in)
Standard
: 27.360 - 27.385 mm (1.0772 - 1.0781 in)
KBIA2404J
CAMSHAFT
EM-83
C
D
E
F
G
H
I
J
K
L
M
A
EM
Revision: 2005 August
2005 Murano
2.
Measure the camshaft sprocket runout with a dial indicator.
(Total indicator reading)
●
If it exceeds the limit, replace camshaft sprocket.
Valve Lifter
Check if surface of valve lifter has any wear or cracks.
●
If anything above is found, replace valve lifter. Refer to
Valve Lifter Clearance
VALVE LIFTER OUTER DIAMETER
●
Measure the outer diameter at 1/2 height of valve lifter with a
micrometer since valve lifter is in barrel shape.
VALVE LIFTER HOLE DIAMETER
●
Measure the inner diameter of valve lifter hole of cylinder head
with an inside micrometer.
VALVE LIFTER CLEARANCE
●
(Valve lifter clearance) = (Valve lifter hole diameter) – (Valve lifter outer diameter)
●
If the calculated value is out of the standard, referring to each standard of valve lifter outer diameter and
valve lifter hole diameter, replace either or both valve lifter and cylinder head.
Limit
: 0.15 mm (0.0059 in)
PBIC0930E
KBIA0182E
Standard (Intake and exhaust)
: 33.977 - 33.987 mm (1.3377 - 1.3381 in)
JEM798G
Standard (Intake and exhaust)
: 34.000 - 34.016 mm (1.3386 - 1.3392 in)
SEM867E
Standard (Intake and exhaust)
: 0.013 - 0.039 mm (0.0005 - 0.0015 in)
EM-84
CAMSHAFT
Revision: 2005 August
2005 Murano
INSTALLATION
1.
Install timing chain tensioners (secondary) on both sides of cyl-
inder head.
●
Install timing chain tensioner with its stopper pin attached.
●
Install timing chain tensioner with sliding part facing down-
ward on right-side cylinder head, and with sliding part facing
upward on left-side cylinder head.
●
Install new O-rings as shown in the figure.
2.
Install valve lifters.
●
Install it in the original position.
3.
Install camshafts.
●
Install camshaft with dowel pin attached to its front end face
on the exhaust side.
●
Follow your identification marks made during removal, or fol-
low the identification marks that are present on new cam-
shafts for proper placement and direction.
●
Install camshaft so that dowel pin hole and dowel pin on front
end face are positioned as shown in figure. (No. 1 cylinder
TDC on its compression stroke)
NOTE:
●
Large and small pin holes are located on front end face of
camshaft (INT), at intervals of 180 degrees. Face small dia.
side pin hole upward (in cylinder head upper face direc-
tion).
●
Though camshaft does not stop at the portion as shown in
the figure, for the placement of cam nose, it is generally
accepted camshaft is placed for the same direction of the
figure.
SBIA0499E
KBIA1071E
Bank
INT/EXH
Dowel pin
Paint marks
ID mark
M1
M2
RH
INT
No
Pink
No
RE
EXH
Yes
No
Orange
RE
LH
INT
No
Pink
No
LH
EXH
Yes
No
Orange
LH
KBIA1009E
PBIC2478E
CAMSHAFT
EM-85
C
D
E
F
G
H
I
J
K
L
M
A
EM
Revision: 2005 August
2005 Murano
4.
Install camshaft brackets.
●
Remove foreign material completely from camshaft bracket
backside and from cylinder head installation face.
●
Install camshaft bracket in original position and direction as
shown in figure.
●
Install camshaft brackets (No. 2 to 4) aligning the stamp
marks as shown in the figure.
NOTE:
There are no identification marks indicating left and right for
camshaft bracket (No. 1).
●
Apply liquid gasket to mating surface of camshaft bracket (No.
1) as shown on right and left banks.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-47, "RECOMMENDED CHEMICAL PRODUCTS AND
SEALANTS"
SEM446G
PBIC2052E
PBIC2660E
EM-86
CAMSHAFT
Revision: 2005 August
2005 Murano
5.
Tighten camshaft bracket bolts in the following steps, in numeri-
cal order as shown.
a.
Tighten No. 7 to 10 in order as shown.
b.
Tighten No. 1 to 6 in order as shown.
c.
Tighten No. 1 to 10 in numerical order as shown.
d.
Tighten No. 1 to 6 in numerical order as shown.
e.
Tighten No. 7 to 10 in numerical order as shown.
CAUTION:
After tightening mounting bolts of camshaft brackets (No.
1), be sure to wipe off excessive liquid gasket from the
parts list below.
●
Mating surface of rocker cover
●
Mating surface of rear timing chain case
6.
Measure difference in levels between front end faces of cam-
shaft bracket (No. 1) and cylinder head.
●
Measure two positions (both intake and exhaust side) for a
single bank.
●
If the measured value is out of the standard, re-install cam-
shaft bracket (No. 1).
7.
Inspect and adjust the valve clearance. Refer to
8.
Install in the reverse order of removal after this step.
INSPECTION AFTER INSTALLATION
Inspection of Camshaft Sprocket (INT) Oil Groove
CAUTION:
●
Perform this inspection only when DTC P0011 or P0021 are detected in self-diagnostic results of
CONSULT-II and it is directed according to inspection procedure of EC section. Refer to
●
Check when engine ins cold so as to prevent burns from any splashing engine oil.
1.
Check the engine oil level. Refer to
2.
Perform the following procedure so as to prevent the engine from being unintentionally started while
checking.
a.
Release fuel pressure. Refer to
EC-92, "FUEL PRESSURE RELEASE"
b.
Disconnect ignition coil and injector harness connectors.
3.
Remove intake valve timing control solenoid valve. Refer to
.
: 1.96 N·m (0.20 kg-m, 1 ft-lb)
: 1.96 N·m (0.20 kg-m, 1 ft-lb)
: 5.88 N·m (0.60 kg-m, 4 ft-lb)
: 10.4 N·m (1.1 kg-m, 8 ft-lb)
: 9.3 N·m (0.95 kg-m, 82 ft-lb)
PBIC2050E
Standard
: –0.14 to 0.14 mm (–0.0055 to 0.0055 in)
EMQ0044D
CAMSHAFT
EM-87
C
D
E
F
G
H
I
J
K
L
M
A
EM
Revision: 2005 August
2005 Murano
4.
Crank the engine, and then make sure that engine oil comes out
from camshaft bracket (No. 1) oil hole. End crank after checking.
WARNING:
Be careful not to touch rotating parts (drive belts, idler pul-
ley, and crankshaft pulley, etc.).
CAUTION:
Engine oil may squirt from intake valve timing control sole-
noid valve installation hole during cranking. Use a shop
cloth to prevent the engine components and the vehicle. Do
not allow engine oil to get on rubber components such as
drive belt or engine mount insulators. Immediately wipe off
any splashed engine oil.
●
Clean oil groove between oil strainer and intake valve timing control solenoid valve if engine oil does not
come out from camshaft bracket (No. 1) oil hole. Refer to
5.
Remove components between intake valve timing control solenoid valve and camshaft sprocket (INT),
and then check each oil groove for clogging.
●
Clean oil groove if necessary. Refer to
6.
After inspection, install removed parts.
Inspection for Leaks
The following are procedures for checking fluids leak, lubricates leak and exhaust gases leak.
●
Before starting engine, check oil/fluid levels including engine coolant and engine oil. If less than required
quantity, fill to the specified level. Refer to
MA-10, "RECOMMENDED FLUIDS AND LUBRICANTS"
●
Use procedure below to check for fuel leakage.
–
Turn ignition switch “ON” (with engine stopped). With fuel pressure applied to fuel piping, check for fuel
leakage at connection points.
–
Start engine. With engine speed increased, check again for fuel leakage at connection points.
●
Run engine to check for unusual noise and vibration.
NOTE:
If hydraulic pressure inside timing chain tensioner drops after removal/installation, slack in the guide may
generate a pounding noise during and just after engine start. However, this is normal. Noise will stop after
hydraulic pressure rises.
●
Warm up engine thoroughly to make sure there is no leakage of fuel, exhaust gases, or any oil/fluids
including engine oil and engine coolant.
●
Bleed air from lines and hoses of applicable lines, such as in cooling system.
●
After cooling down engine, again check oil/fluid levels including engine oil and engine coolant. Refill to the
specified level, if necessary.
Summary of the inspection items:
* Transmission/transaxle/CVT fluid. power steering fluid, brake fluid, etc.
PBIC2869E
Item
Before starting engine
Engine running
After engine stopped
Engine coolant
Level
Leakage
Level
Engine oil
Level
Leakage
Level
Other oils and fluid*
Level
Leakage
Level
Fuel
Leakage
Leakage
Leakage
Exhaust gases
—
Leakage
—
EM-88
CAMSHAFT
Revision: 2005 August
2005 Murano
Valve Clearance
ABS003MI
INSPECTION
In cases of removing/installing or replacing camshaft and valve-
related parts, or of unusual engine conditions due to changes in
valve clearance (found malfunctions during stating, idling or causing
noise), perform inspection as follows:
1.
Remove rocker covers (right and left banks). Refer to
.
2.
Measure the valve clearance as follows:
a.
Set No. 1 cylinder at TDC of its compression stroke.
●
Rotate crankshaft pulley clockwise to align timing mark
(grooved line without color) with timing indicator.
●
Make sure that intake and exhaust cam noses on No. 1 cylin-
der (engine front side of right bank) are located as shown in
the figure.
●
If not, turn crankshaft one revolution (360 degrees) and align
as shown in the figure.
b.
Use a feeler gauge, measure the clearance between valve lifter
and camshaft.
SEM713A
SEM918G
SEM418G
SEM139D
CAMSHAFT
EM-89
C
D
E
F
G
H
I
J
K
L
M
A
EM
Revision: 2005 August
2005 Murano
Valve clearance:
Unit: mm (in)
*: Approximately 80
°
C (176
°
F)
●
By referring to the figure, measure the valve clearances at
locations marked “
×
” as shown in the table below (locations
indicated in the figure).
●
No. 1 cylinder at compression TDC
c.
Rotate crankshaft by 240 degrees clockwise (when viewed from
engine front) to align No. 3 cylinder at TDC of its compression
stroke.
NOTE:
Crankshaft pulley mounting bolt flange has a stamped line every
60 degrees. They can be used as a guide to rotation angle.
Items
Cold
Hot * (reference data)
Intake
0.26 - 0.34 (0.010 - 0.013)
0.304 - 0.416 (0.012 - 0.016)
Exhaust
0.29 - 0.37 (0.011 - 0.015)
0.308 - 0.432 (0.012 - 0.016)
Measuring position (right bank)
No. 1 CYL.
No. 3 CYL.
No. 5 CYL.
No. 1 cylinder at
compression TDC
EXH
×
INT
×
Measuring position (left bank)
No. 2 CYL.
No. 4 CYL.
No. 6 CYL.
No. 1 cylinder at
compression TDC
INT
×
EXH
×
PBIC2054E
SEM751G
EM-90
CAMSHAFT
Revision: 2005 August
2005 Murano
●
By referring to the figure, measure the valve clearances at
locations marked “
×
” as shown in the table below (locations
indicated in the figure).
●
No. 3 cylinder at compression TDC
d.
Rotate crankshaft by 240 degrees clockwise (when viewed from
engine front) to align No. 5 cylinder at TDC of compression
stroke.
●
By referring to the figure, measure the valve clearances at
locations marked “
×
” as shown in the table below (locations
indicated in the figure).
●
No. 5 cylinder at compression TDC
Measuring position (right bank)
No. 1 CYL.
No. 3 CYL.
No. 5 CYL.
No. 3 cylinder at
compression TDC
EXH
×
INT
×
Measuring position (left bank)
No. 2 CYL.
No. 4 CYL.
No. 6 CYL.
No. 3 cylinder at
compression TDC
INT
×
EXH
×
PBIC2055E
SEM751G
Measuring position (right bank)
No. 1 CYL.
No. 3 CYL.
No. 5 CYL.
No. 5 cylinder at
compression TDC
EXH
×
INT
×
Measuring position (left bank)
No. 2 CYL.
No. 4 CYL.
No. 6 CYL.
No. 5 cylinder at
compression TDC
INT
×
EXH
×
PBIC2056E
CAMSHAFT
EM-91
C
D
E
F
G
H
I
J
K
L
M
A
EM
Revision: 2005 August
2005 Murano
3.
For the measured value are out of the standard, perform adjustment. Refer to
ADJUSTMENT
●
Perform adjustment depending on selected head thickness of valve lifter.
1.
Measure the valve clearance. Refer to
2.
Remove camshaft. Refer to
3.
Remove valve lifters at the locations that are out of the standard.
4.
Measure the center thickness of the removed valve lifters with a
micrometer.
5.
Use the equation below to calculate valve lifter thickness for replacement.
●
Thickness of new valve lifter can be identified by stamp marks
on the reverse side (inside the cylinder).
Stamp mark 788U or 788R indicates 7.88 mm (0.3102 in) in
thickness.
NOTE:
Two types of stamp marks are used for parallel setting and for
manufacturer identification.
Available thickness of valve lifter: 27 sizes with range 7.88 to 8.40 mm (0.3102 to 0.3307 in) in steps of
0.02 mm (0.0008 in) (when manufactured at factory). Refer to
EM-144, "Available Valve Lifter"
6.
Install selected valve lifter.
7.
.
8.
Manually turn crankshaft pulley a few turns.
9.
Make sure that the valve clearances for cold engine are within the specifications by referring to the speci-
fied values. Refer to
10. Install all removal parts in the reverse order of removal. Refer to
11. Warm up the engine, and check for unusual noise and vibration.
KBIA0057E
Valve lifter thickness calculation:
t = t
1
+ (C
1
– C
2
)
t
= Valve lifter thickness to be replaced
t
1
= Removed valve lifter thickness
C
1
= Measured valve clearance
C
2
= Standard valve clearance:
Intake
: 0.30 mm (0.012 in)*
Exhaust
: 0.33 mm (0.013 in)*
*: Approximately 20
°
C (68
°
F)
KBIA0119E
EM-92
OIL SEAL
Revision: 2005 August
2005 Murano
OIL SEAL
PFP:00100
Removal and Installation of Valve Oil Seal
ABS003MJ
REMOVAL
1.
Remove engine assembly from the vehicle, and separate front suspension member, transaxle and trans-
fer (AWD models) assembly from engine. Refer to
.
2.
Install engine sub-attachment with engine stand shaft [SST: KV10117001 (
—
) and KV10106500 (
—
)] to right side of cylinder block, then lift engine, and mount it onto engine stand [SST: ST0501S000
(
—
)]. Refer to
3.
Remove camshaft relating to valve oil seal to be removed. Refer to
4.
Remove valve lifters. Refer to
5.
Turn crankshaft until the cylinder requiring new oil seals is at TDC. This will prevent valve from dropping
into cylinder.
6.
Remove valve collet.
●
Compress valve spring with the valve spring compressor, the
attachment, the adapter [SST]. Remove valve collet with a
magnet hand.
CAUTION:
When working, take care not to damage valve lifter holes.
7.
Remove valve spring retainer and valve spring.
8.
Remove valve oil seal using the valve oil seal puller [SST].
INSTALLATION
1.
Apply new engine oil on new valve oil seal joint and seal lip.
2.
Using the valve oil seal drift [SST], press fit valve seal to height
“H” shown in figure.
NOTE:
Dimension “H”: Height measured before valve spring seat instal-
lation
3.
Install in the reverse order of removal after this step.
PBIC1803E
PBIC0884E
Intake and exhaust
: 14.3 - 14.9 mm (0.563 - 0.587 in)
PBIC2769E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст