Nissan Murano Z50 (2005 year). Manual — part 210
SE-1
SEAT
I BODY
CONTENTS
C
D
E
F
G
H
J
K
L
M
SECTION
SE
A
B
SE
Revision: 2005 August
2005 Murano
SEAT
PRECAUTIONS . . . . . . . . . . . . . . .. 3
PREPARATION . . . . . . . . . . . . . . ... 4
Special Service Tools . . . . . . . . . . . ... 4
Commercial Service Tools . . . . . . . . . . 4
SQUEAK AND RATTLE TROUBLE DIAGNOSES . . 5
Work Flow . . . . . . . . . . . . . . . . 5
Generic Squeak and Rattle Troubleshooting . . ... 7
Diagnostic Worksheet . . . . . . . . . . . .. 9
CLIP AND FASTENER . . . . . . . . . . . ..11
Clip and Fastener . . . . . . . . . . . . . 11
AUTOMATIC DRIVE POSITIONER . . . . . . .. 12
System Description . . . . . . . . . . . . 12
KEYFOB INTERLOCK OPERATION . . . . .. 16
Component Parts And Harness Connector Location
SE-2
Revision: 2005 August
2005 Murano
POWER SEAT . . . . . . . . . . . . . . ... 93
HEATED SEAT . . . . . . . . . . . . . . .. 99
FRONT SEAT . . . . . . . . . . . . . . ..104
Removal and Installation . . . . . . . . . ...104
REAR SEAT . . . . . . . . . . . . . . . . 111
PRECAUTIONS
SE-3
C
D
E
F
G
H
J
K
L
M
A
B
SE
Revision: 2005 August
2005 Murano
PRECAUTIONS
PFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
AIS0038H
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
●
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
●
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
●
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Service Notice
AIS0038G
●
When removing or installing various parts, place a cloth or padding onto the vehicle body to prevent
scratches.
●
Handle trim, molding, instruments, grille, etc. carefully during removing or installing. Be careful not to oil or
damage them.
●
Apply sealing compound where necessary when installing parts.
●
When applying sealing compound, be careful that the sealing compound does not protrude from parts.
●
When replacing any metal parts (for example body outer panel, members, etc.), be sure to take rust pre-
vention measures.
Precautions for Work
AIS0038I
●
When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a cloth.
●
When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the compo-
nent with a cloth or vinyl tape to protect it.
●
Protect the removed parts with a cloth and keep them.
●
Replace a deformed or damaged clip.
●
If a part is specified as a non-reusable part, always replace it with new one.
●
Be sure to tighten bolts and nuts securely to the specified torque.
●
After re-installation is completed, be sure to check that each part works normally.
●
Follow the steps below to clean components.
–
Water soluble foul: Dip a soft cloth into lukewarm water, and wring the water out of the cloth to wipe the
fouled area.
Then rub with a soft and dry cloth.
–
Oily foul: Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%), and wipe
the fouled area.
Then dip a cloth into fresh water, and wring the water out of the cloth to wipe the detergent off. Then rub
with a soft and dry cloth.
●
Do not use organic solvent such as thinner, benzene, alcohol, and gasoline.
●
For genuine leather seats, use a genuine leather seat cleaner.
SE-4
PREPARATION
Revision: 2005 August
2005 Murano
PREPARATION
PFP:00002
Special Service Tools
AIS001T7
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
AIS001T8
Tool number
(Kent-Moore No.)
Tool name
Description
(J-39570)
Chassis ear
Locating the noise
(J-43980)
NISSAN Squeak and Rattle
Kit
Repairing the cause of noise
SIIA0993E
SIIA0994E
Tool name
Description
Engine ear
Locating the noise
SIIA0995E
SQUEAK AND RATTLE TROUBLE DIAGNOSES
SE-5
C
D
E
F
G
H
J
K
L
M
A
B
SE
Revision: 2005 August
2005 Murano
SQUEAK AND RATTLE TROUBLE DIAGNOSES
PFP:00000
Work Flow
AIS0038Y
CUSTOMER INTERVIEW
Interview the customer if possible, to determine the conditions that exist when the noise occurs. Use the Diag-
nostic Worksheet during the interview to document the facts and conditions when the noise occurs and any
customer's comments; refer to
. This information is necessary to duplicate the
conditions that exist when the noise occurs.
●
The customer may not be able to provide a detailed description or the location of the noise. Attempt to
obtain all the facts and conditions that exist when the noise occurs (or does not occur).
●
If there is more than one noise in the vehicle, be sure to diagnose and repair the noise that the customer
is concerned about. This can be accomplished by test driving the vehicle with the customer.
●
After identifying the type of noise, isolate the noise in terms of its characteristics. The noise characteristics
are provided so the customer, service adviser and technician are all speaking the same language when
defining the noise.
●
Squeak —(Like tennis shoes on a clean floor)
Squeak characteristics include the light contact/fast movement/brought on by road conditions/hard sur-
faces=higher pitch noise/softer surfaces=lower pitch noises/edge to surface=chirping
●
Creak—(Like walking on an old wooden floor)
Creak characteristics include firm contact/slow movement/twisting with a rotational movement/pitch
dependent on materials/often brought on by activity.
●
Rattle—(Like shaking a baby rattle)
Rattle characteristics include the fast repeated contact/vibration or similar movement/loose parts/missing
clip or fastener/incorrect clearance.
●
Knock —(Like a knock on a door)
Knock characteristics include hollow sounding/sometimes repeating/often brought on by driver action.
●
Tick—(Like a clock second hand)
Tick characteristics include gentle contacting of light materials/loose components/can be caused by driver
action or road conditions.
●
Thump—(Heavy, muffled knock noise)
Thump characteristics include softer knock/dead sound often drought on by activity.
●
Buzz—(Like a bumble bee)
Buzz characteristics include high frequency rattle/firm contact.
●
Often the degree of acceptable noise level will vary depending upon the person. A noise that you may
judge as acceptable may be very irritating to the customer.
●
Weather conditions, especially humidity and temperature, may have a great effect on noise level.
SBT842
SE-6
SQUEAK AND RATTLE TROUBLE DIAGNOSES
Revision: 2005 August
2005 Murano
DUPLICATE THE NOISE AND TEST DRIVE
If possible, drive the vehicle with the customer until the noise is duplicated. Note any additional information on
the Diagnostic Worksheet regarding the conditions or location of the noise. This information can be used to
duplicate the same conditions when you confirm the repair.
If the noise can be duplicated easily during the test drive, to help identify the source of the noise, try to dupli-
cate the noise with the vehicle stopped by doing one or all of the following:
1) Close a door.
2) Tap or push/pull around the area where the noise appears to be coming from.
3) Rev the engine.
4) Use a floor jack to recreate vehicle “twist”.
5) At idle, apply engine load (electrical load, half-clutch on M/T model, drive position on A/T model).
6) Raise the vehicle on a hoist and hit a tire with a rubber hammer.
●
Drive the vehicle and attempt to duplicate the conditions the customer states exist when the noise occurs.
●
If it is difficult to duplicate the noise, drive the vehicle slowly on an undulating or rough road to stress the
vehicle body.
CHECK RELATED SERVICE BULLETINS
After verifying the customer concern or symptom, check ASIST for Technical Service Bulletins (TSBs) related
to that concern or symptom.
If a TSB relates to the symptom, follow the procedure to repair the noise.
LOCATE THE NOISE AND IDENTIFY THE ROOT CAUSE
1.
Narrow down the noise to a general area. To help pinpoint the source of the noise, use a listening tool
(Chassis Ear: J-39570, Engine Ear and mechanics stethoscope).
2.
Narrow down the noise to a more specific area and identify the cause of the noise by:
●
removing the components in the area that you suspect the noise is coming from.
Do not use too much force when removing clips and fasteners, otherwise clips and fastener can be broken
or lost during the repair, resulting in the creation of new noise.
●
tapping or pushing/pulling the component that you suspect is causing the noise.
Do not tap or push/pull the component with excessive force, otherwise the noise will be eliminated only
temporarily.
●
feeling for a vibration with your hand by touching the component(s) that you suspect is (are) causing the
noise.
●
placing a piece of paper between components that you suspect are causing the noise.
●
looking for loose components and contact marks.
Refer to
SE-7, "Generic Squeak and Rattle Troubleshooting"
.
REPAIR THE CAUSE
●
If the cause is a loose component, tighten the component securely.
●
If the cause is insufficient clearance between components:
–
separate components by repositioning or loosening and retightening the component, if possible.
–
insulate components with a suitable insulator such as urethane pads, foam blocks, felt cloth tape or ure-
thane tape. A Nissan Squeak and Rattle Kit (J-43980) is available through your authorized Nissan Parts
Department.
CAUTION:
Do not use excessive force as many components are constructed of plastic and may be damaged.
Always check with the Parts Department for the latest parts information.
The following materials are contained in the Nissan Squeak and Rattle Kit (J-43980). Each item can be
ordered separately as needed.
URETHANE PADS [1.5 mm (0.059 in) thick]
Insulates connectors, harness, etc.
76268-9E005: 100
×
135 mm (3.94
×
5.31 in)/76884-71L01: 60
×
85 mm (2.36
×
3.35 in)/76884-71L02: 15
×
25 mm (0.59
×
0.98 in)
INSULATOR (Foam blocks)
Insulates components from contact. Can be used to fill space behind a panel.
73982-9E000: 45 mm (1.77 in) thick, 50
×
50 mm (1.97
×
1.97 in)/73982-50Y00: 10 mm (0.39 in) thick,
50
×
50 mm (1.97
×
1.97 in)
SQUEAK AND RATTLE TROUBLE DIAGNOSES
SE-7
C
D
E
F
G
H
J
K
L
M
A
B
SE
Revision: 2005 August
2005 Murano
INSULATOR (Light foam block)
80845-71L00: 30 mm (1.18 in) thick, 30
×
50 mm (1.18
×
1.97 in)
FELT CLOTHTAPE
Used to insulate where movement does not occur. Ideal for instrument panel applications.
68370-4B000: 15
×
25 mm (0.59
×
0.98 in) pad/68239-13E00: 5 mm (0.20 in) wide tape roll
The following materials, not found in the kit, can also be used to repair squeaks and rattles.
UHMW (TEFLON) TAPE
Insulates where slight movement is present. Ideal for instrument panel applications.
SILICONE GREASE
Used in of UHMW tape that will be visible or not fit.
Note: Will only last a few months.
SILICONE SPRAY
Use when grease cannot be applied.
DUCT TAPE
Use to eliminate movement.
CONFIRM THE REPAIR
Confirm that the cause of a noise is repaired by test driving the vehicle. Operate the vehicle under the same
conditions as when the noise originally occurred. Refer to the notes on the Diagnostic Worksheet.
Generic Squeak and Rattle Troubleshooting
AIS0038Z
Refer to Table of Contents for specific component removal and installation information.
INSTRUMENT PANEL
Most incidents are caused by contact and movement between:
1.
Cluster lid A and instrument panel
2.
Acrylic lens and combination meter housing
3.
Instrument panel to front pillar garnish
4.
Instrument panel to windshield
5.
Instrument panel mounting pins
6.
Wiring harnesses behind the combination meter
7.
A/C defroster duct and duct joint
These incidents can usually be located by tapping or moving the components to duplicate the noise or by
pressing on the components while driving to stop the noise. Most of these incidents can be repaired by apply-
ing felt cloth tape or silicon spray (in hard to reach areas). Urethane pads can be used to insulate wiring har-
ness.
CAUTION:
Do not use silicone spray to isolate a squeak or rattle. If you saturate the area with silicone, you will
not be able to recheck the repair.
CENTER CONSOLE
Components to pay attention to include:
1.
Shifter assembly cover to finisher
2.
A/C control unit and cluster lid C
3.
Wiring harnesses behind audio and A/C control unit
The instrument panel repair and isolation procedures also apply to the center console.
DOORS
Pay attention to the:
1.
Finisher and inner panel making a slapping noise
2.
Inside handle escutcheon to door finisher
3.
Wiring harnesses tapping
4.
Door striker out of alignment causing a popping noise on starts and stops
Tapping or moving the components or pressing on them while driving to duplicate the conditions can isolate
many of these incidents. You can usually insulate the areas with felt cloth tape or insulator foam blocks from
the Nissan Squeak and Rattle Kit (J-43980) to repair the noise.
SE-8
SQUEAK AND RATTLE TROUBLE DIAGNOSES
Revision: 2005 August
2005 Murano
TRUNK
Trunk noises are often caused by a loose jack or loose items put into the trunk by the owner.
In addition look for:
1.
Trunk lid dumpers out of adjustment
2.
Trunk lid striker out of adjustment
3.
Trunk lid torsion bars knocking together
4.
A loose license plate or bracket
Most of these incidents can be repaired by adjusting, securing or insulating the item(s) or component(s) caus-
ing the noise.
SUNROOF/HEADLINING
Noises in the sunroof/headlining area can often be traced to one of the following:
1.
Sunroof lid, rail, linkage or seals making a rattle or light knocking noise
2.
Sunvisor shaft shaking in the holder
3.
Front or rear windshield touching headlining and squeaking
Again, pressing on the components to stop the noise while duplicating the conditions can isolate most of these
incidents. Repairs usually consist of insulating with felt cloth tape.
SEATS
When isolating seat noise it's important to note the position the seat is in and the load placed on the seat when
the noise is present. These conditions should be duplicated when verifying and isolating the cause of the
noise.
Cause of seat noise include:
1.
Headrest rods and holder
2.
A squeak between the seat pad cushion and frame
3.
Seatback lock and bracket
These noises can be isolated by moving or pressing on the suspected components while duplicating the con-
ditions under which the noise occurs. Most of these incidents can be repaired by repositioning the component
or applying urethane tape to the contact area.
UNDERHOOD
Some interior noise may be caused by components under the hood or on the engine wall. The noise is then
transmitted into the passenger compartment.
Causes of transmitted underhood noise include:
1.
Any component mounted to the engine wall
2.
Components that pass through the engine wall
3.
Engine wall mounts and connectors
4.
Loose radiator mounting pins
5.
Hood bumpers out of adjustment
6.
Hood striker out of adjustment
These noises can be difficult to isolate since they cannot be reached from the interior of the vehicle. The best
method is to secure, move or insulate one component at a time and test drive the vehicle. Also, engine RPM
or load can be changed to isolate the noise. Repairs can usually be made by moving, adjusting, securing, or
insulating the component causing the noise.
SQUEAK AND RATTLE TROUBLE DIAGNOSES
SE-9
C
D
E
F
G
H
J
K
L
M
A
B
SE
Revision: 2005 August
2005 Murano
Diagnostic Worksheet
AIS00390
PIIB0723E
SE-10
SQUEAK AND RATTLE TROUBLE DIAGNOSES
Revision: 2005 August
2005 Murano
SBT844
CLIP AND FASTENER
SE-11
C
D
E
F
G
H
J
K
L
M
A
B
SE
Revision: 2005 August
2005 Murano
CLIP AND FASTENER
PFP:76906
Clip and Fastener
AIS003C2
SIIA0315E
SE-12
AUTOMATIC DRIVE POSITIONER
Revision: 2005 August
2005 Murano
AUTOMATIC DRIVE POSITIONER
PFP:28491
System Description
AIS003GD
MANUAL OPERATION
The driving position [seat position pedal position (Accelerator, brake) and door mirror position] can be adjusted
with the power seat switch or pedal adjusting switch or door mirror remote control switch.
NOTE:
●
The door mirrors can be manually operated with the ignition switch turned ACC or ON.
●
Only when CVT selector lever is in P position, adjusting pedal operates (except when ignition switch
turned to OFF).
●
If detection switch error is detected, manual adjustable pedal operation cannot be performed when igni-
tion switch turns ON.
AUTOMATIC OPERATION
●
The system automatically moves the driver seat to facilitate entry/exit to/from the vehicle. The driver seat
control unit can also store the optimum driving positions (driver seat, pedal position and door mirror posi-
tion) for 2 people. If the driver is changes, one-touch operation allows changing to the other driving posi-
tion.
●
The settings (ON/OFF) of the automatic sliding seat (Entry/Exiting operation) at entry/exit can be changed
as desired, using the display unit in the center of the instrument panel. The set content is transmitted by
CAN communication, from display unit (without NAVI) or display control unit (with NAVI) to driver seat con-
trol unit.
●
Using CONSULT-ll, the seat slide a mount at entry/exit setting can be changed.
NOTE:
●
Disconnecting the battery erases the stored memory.
●
After connecting the battery, insert the key into the ignition cylinder and turn the driver door switch ON (open)
→
OFF (close)
→
ON
(open), the Entry/ Exiting function becomes possible.
●
After Exiting operation is carried out, return operation can be operated.
NOTE:
During automatic operation, if the ignition switch is turned ON
→
START, the automatic operation is suspended. When the ignition switch
returns to ON, it resumes.
Function Description
Memory operation
The seat, pedal (accelerator, brake) and door mirror move to the stored driving posi-
tion by pushing memory switch (1 or 2).
Entry/Exit-
ing function
Exiting operation
At Exit, the seat moves backward. (Exiting position)
Entry operation
At entry, the seat returns from Exiting position to the previous driving position before
the Exiting operation.
Keyfob interlock operation
Perform memory operation, turnout operation and return operation by pressing key-
fob unlock button.
Auto operation temporary stop
conditions.
When ignition switch turned to START during memory switch operation and return opera-
tion, memory switch operation and return operation is stopped.
Auto operation stop conditions.
●
When the vehicle speed becomes 7 km/h (4 MPH) or higher. (memory switch operation
and entry operation)
●
When the setting switch, memory switch 1, or 2 are pressed.
●
When CVT selector lever is in any position other than P.
●
When the door mirror remote control switch is operated (when ignition switch or ACC
switch turned to ON).
●
When power seat switch turned ON.
●
When pedal adjusting switch turned ON.
●
When driver seat sliding Entry/Exiting setting is OFF (entry/exiting operation).
AUTOMATIC DRIVE POSITIONER
SE-13
C
D
E
F
G
H
J
K
L
M
A
B
SE
Revision: 2005 August
2005 Murano
FAIL- SAFE MODE
When any manual and automatic operations are not performed, if any motor operations of seats or pedals are
detected for T2 or more, status is judged “Output error”.
CANCEL OF FAIL-SAFE MODE
The mode is cancelled when the selector lever is shifted to P position from any other position.
OPERATED PORTION
T2
Seat sliding
Approx. 0.1 sec.
Seat reclining
Same as above
Seat lifting (Front)
Same as above
Seat lifting (Rear)
Same as above
Pedal adjust
Same as above
SE-14
AUTOMATIC DRIVE POSITIONER
Revision: 2005 August
2005 Murano
MEMORY STORING AND KEYFOB INTERLOCK STORING
●
Store the 2 driving positions and shifts to the stored driving position with the memory switch.
●
Keyfob interlock function is set simultaneously with setting driving position memory. It can set driving posi-
tion to memory position.
NOTE:
●
If another keyfob interlock function setting is performed by same key, newly registered setting is valid.
●
If new memory string is performed to memory switch that already set keyfob interlock function, keyfob
interlock function setting is reset.
●
If keyfob does not set previously, keyfob interlock function cannot set.
PIIB3488E
AUTOMATIC DRIVE POSITIONER
SE-15
C
D
E
F
G
H
J
K
L
M
A
B
SE
Revision: 2005 August
2005 Murano
MEMORY OPERATION
Selecting the memorized position.
NOTE:
The driver's seat position and pedal adjustment functions (see the following table) operate simultaneously in
the order of priority.
*: In conjunction with sliding the seat, the door mirrors are positioned.
ENTRY OPERATION
When the seat are on the exiting positions, the following operation moves the seat to the previous position
before the exiting operation.
EXITING OPERATION
At Entry/Exiting, the seat are automatically moved to the exiting position.
Priority
Function
Priority
Function
1
Seat sliding, (door mirror LH/RH)*
4
Seat lifter-FR
2
Pedal
5
Seat lifter-RR
3
Seat reclining
PIIA4798E
PIIB2805E
PIIB2806E
SE-16
AUTOMATIC DRIVE POSITIONER
Revision: 2005 August
2005 Murano
KEYFOB INTERLOCK OPERATION
●
The system performs memory operation, exiting operation and return operation by pressing keyfob unlock
button.
NOTE:
●
If Entry/Exiting operation is cancelled, the system performs memory operation only.
●
If ignition switch turns ON in the middle of memory operation, the system does not perform exiting opera-
tion after memory operation.
●
If ignition switch turns ON in the middle of exiting operation, entry operation starts at that time.
PIIA4797E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст