Nissan Murano Z50 (2005 year). Manual — part 43
INTEGRATED HOMELINK TRANSMITTER
BL-257
C
D
E
F
G
H
J
K
L
M
A
B
BL
Revision: 2005 August
2005 Murano
INTEGRATED HOMELINK TRANSMITTER
PFP:96401
Wiring Diagram —TRNSCV—
AIS002WQ
TIWA0443E
BL-258
INTEGRATED HOMELINK TRANSMITTER
Revision: 2005 August
2005 Murano
Trouble Diagnoses
AIS002WR
DIAGNOSTIC PROCEDURE
SYMPTOM: Transmitter Does Not Activate Receiver
Before conducting the procedure given below, make sure that system receiver (garage door opener, etc.)
operates with original, hand-held transmitter. If NG, receiver or hand-held transmitter is malfunctioning, not
vehicle related.
1.
CHECK ILLUMINATION
1.
Turn ignition switch “OFF”.
2.
Does red light (LED) of transmitter illuminate when any transmit-
ter button is pressed?
YES or NO
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
CHECK TRANSMITTER
Check auto anti-dazzling inside mirror (homelink universal transceiver) with Tool*.
*:For details, refer to Technical Service Bulletin.
OK or NG
OK
>> Receiver or hand-held transmitter malfunction, not vehicle related.
NG
>> Replace inside mirror assembly.
3.
CHECK POWER SUPPLY
1.
Disconnect auto anti-dazzling inside mirror (homelink universal transceiver) connector.
2.
Turn ignition switch “OFF”.
3.
Check voltage between auto anti-dazzling inside mirror (homelink universal transceiver) connector R4 ter-
minal 5 (Y) and ground.
OK or NG
OK
>> GO TO 4.
NG
>>
●
Check 10A fuse. [No. 19 located in the fuse block (J/
B)]
●
Repair or replace harness between fuse and anti-daz-
zling inside mirror (homelink universal transceiver).
PIIA4815E
5 (Y) – Ground
: Battery voltage
PIIA2370E
INTEGRATED HOMELINK TRANSMITTER
BL-259
C
D
E
F
G
H
J
K
L
M
A
B
BL
Revision: 2005 August
2005 Murano
4.
CHECK GROUND CIRCUIT
Check continuity between anti-dazzling inside mirror (homelink uni-
versal transceiver) connector R4 terminal 8 (B) and ground.
OK or NG
OK
>> Replace inside mirror assembly.
NG
>> Harness for open or short between anti-dazzling inside
mirror (homelink universal transceiver) ground.
8 (B) – Ground
:Continuity should exist.
PIIA2368E
BL-260
BODY REPAIR
Revision: 2005 August
2005 Murano
BODY REPAIR
PFP:60100
Body Exterior Paint Color
AIS001XT
2S:Solid + Clear,
M:Metallic, P:Pearl, 2P:2-Coat pearl, 3P:3-Coat pearl, FPM:Iron oxide pearl, RPM:Multi flex color
Component
Color code
BAX5
BBW9
BEY0
BK21
BKH3
BKY0
BQX1
BR10
Description
RED
Dark
Blue
Light
Gold
Gray
Black
Silver
White
Orange
Paint type
2P
2P
RPM
FPM
2S
M
3P
M
Hard clear coat
×
×
-
-
×
-
-
-
1 Bumper fas-
cia
Upper
Body color
BAX5
BBW9
BEY0
BK21
BKH3
BKY0
BQX1
BR10
Lower
Gray Metallic (M)
BKR2
BKR2
BKR2
BKR2
BKR2
BKR2
BKR2
BKR2
2 Front grille
Chromium-plate +
Color clear coat
Cr2p
Cr2p
Cr2p
Cr2p
Cr2p
Cr2p
Cr2p
Cr2p
3 Door outside
mirror
Housing
Body color
BAX5
BBW9
BEY0
BK21
BKH3
BKY0
BQX1
BR10
Base
Black
BKH3
BKH3
BKH3
BKH3
BKH3
BKH3
BKH3
BKH3
4 Door outside
handle
Chromium-plate
Cr2p
Cr2p
Cr2p
Cr2p
Cr2p
Cr2p
Cr2p
Cr2p
Body color
BAX5
BBW9
BEY0
BK21
BKH3
BKY0
BQX1
BR10
5 Back door
Body color
BAX5
BBW9
BEY0
BK21
BKH3
BKY0
BQX1
BR10
SIIA2069E
BODY REPAIR
BL-261
C
D
E
F
G
H
J
K
L
M
A
B
BL
Revision: 2005 August
2005 Murano
Body Component Parts
AIS001XU
UNDERBODY COMPONENT PARTS
SIIA2388E
BL-262
BODY REPAIR
Revision: 2005 August
2005 Murano
1.
Hoodledge assembly
23. Rear floor side
2.
Upper hoodledge
24. Spare tire clamp bracket
3.
Lower front hoodledge
25. Front side member assembly
4.
Hoodledge reinforcement
26. Front side member
5.
Air box assembly
27. Front side member connector
6.
Side cowl top
28. Bumper stay reinforcement assembly
7.
Lower dash
29. Front suspension mounting bracket
8.
Side dash
30. Front side member outrigger assembly
9.
Front floor
31. Lower dash crossmember
10. Center front floor reinforcement
32. Front side member closing plate assembly
11. Front floor reinforcement (RH&LH)
33. Front side member front closing plate
12. Front side member stiffener
34. Front side member center extension
13. Center floor member assembly
35. Front side member rear extension
14. Inner sill
36. Rear seat crossmember
15. 2ND crossmember assembly
37. Rear side member assembly
16. 3RD crossmember assembly
38. Inner sill extension
17. Rear floor
39. Jack up point bracket
18. Rear floor rear
40. Sill closing plate
19. Rear floor front extension
41. Rear side member extension
20. Rear seat back support assembly
42. Center rear crossmember assembly
21. Outer rear seat belt anchor reinforcement
43. Spare wheel crossmember
22. 2ND seat mounting bracket
BODY REPAIR
BL-263
C
D
E
F
G
H
J
K
L
M
A
B
BL
Revision: 2005 August
2005 Murano
BODY COMPONENT PARTS
1.
Hood
24. Rear roof rail assembly
2.
Front fender (RH&LH)
25. Roof bow No.1
SIIA2389E
BL-264
BODY REPAIR
Revision: 2005 August
2005 Murano
3.
Side body assembly (RH&LH)
26. Roof bow No.3
4.
Upper pillar hinge brace assembly (RH&LH)
27. Roof bow No.4
5.
Lower front pillar hinge brace (RH&LH)
28. Roof bow No.5
6.
Lower front pillar reinforcement (RH&LH)
29. Rear fender assembly (RH&LH)
7.
Center pillar reinforcement (RH&LH)
30. Rear fender extension (RH&LH)
8.
Outer sill reinforcement assembly (RH&LH)
31. Back pillar assembly (RH&LH)
9.
Rear outer sill reinforcement (RH&LH)
32. Rear combination lamp base assembly (RH&LH)
10. Outer sill (RH&LH)
33. Rear bumper fascia rear bracket (RH&LH)
11. Inner side roof rail (RH&LH)
34. Rear combination lamp base extension (RH&LH)
12. Inner center pillar (RH&LH)
35. Fuel filler lid (LH)
13. Inner rear pillar assembly (RH&LH)
36. Rear panel assembly
14. Inner rear pillar reinforcement (RH&LH)
37. Rear bumper fascia bracket
15. Back pillar reinforcement (RH&LH)
38. Front door assembly (RH&LH)
16. Outer rear wheelhouse (RH&LH)
39. Outer front door panel (RH&LH)
17. Inner rear wheelhouse assembly (RH&LH)
40. Rear door assembly (RH&LH)
18. Inner rear wheelhouse front extension (RH&LH)
41. Outer rear door panel (RH&LH)
19. Inner rear wheelhouse rear extension (RH&LH)
42. Front bumper reinforcement
20. Roof
43. Front bumper stay (RH&LH)
21. Roof assembly (for sunroof)
44. Rear bumper reinforcement
22. Front roof rail assembly
45. Rear bumper stay (RH&LH)
23. Roof bow No.2
BODY REPAIR
BL-265
C
D
E
F
G
H
J
K
L
M
A
B
BL
Revision: 2005 August
2005 Murano
Corrosion Protection
AIS001XV
DESCRIPTION
To provide improved corrosion prevention, the following anti-corrosive measures have been implemented in
NISSAN production plants. When repairing or replacing body panels, it is necessary to use the same anti-cor-
rosive measures.
Anti-corrosive Precoated Steel (Galvannealed Steel)
To improve repairability and corrosion resistance, a new type of anti-
corrosive precoated steel sheet has been adopted replacing conven-
tional zinc-coated steel sheet.
Galvannealed steel is electroplated and heated to form Zinc-iron
alloy, which provides excellent and long term corrosion resistance
with cationic electrodeposition primer.
Nissan Genuine Service Parts are fabricated from galvannealed steel. Therefore, it is recommended that
GENUINE NISSAN PARTS or equivalent be used for panel replacement to maintain the anti-corrosive perfor-
mance built into the vehicle at the factory.
Phosphate Coating Treatment and Cationic Electrodeposition Primer
A phosphate coating treatment and a cationic electrodeposition primer, which provide excellent corrosion pro-
tection, are employed on all body components.
CAUTION:
Confine paint removal during welding operations to an absolute
minimum.
Nissan Genuine Service Parts are also treated in the same manner. Therefore, it is recommended that GENU-
INE NISSAN PARTS or equivalent be used for panel replacement to maintain anti-corrosive performance built
into the vehicle at the factory.
SIIA2294E
PIIA0095E
BL-266
BODY REPAIR
Revision: 2005 August
2005 Murano
ANTI-CORROSIVE WAX
To improve corrosion resistance, anti-corrosive wax is applied inside the body sill and inside other closed sec-
tions. Accordingly, when replacing these parts, be sure to apply anti-corrosive wax to the appropriate areas of
the new parts. Select an excellent anti-corrosive wax which will penetrate after application and has a long shelf
life.
SIIA2160E
BODY REPAIR
BL-267
C
D
E
F
G
H
J
K
L
M
A
B
BL
Revision: 2005 August
2005 Murano
UNDERCOATING
The underside of the floor and wheelhouse are undercoated to prevent rust, vibration, noise and stone chip-
ping. Therefore, when such a panel is replaced or repaired, apply undercoating to that part. Use an undercoat-
ing which is rust preventive, soundproof, vibration-proof, shock-resistant, adhesive, and durable.
Precautions in Undercoating
1.
Do not apply undercoating to any place unless specified (such as the areas above the muffler and three
way catalyst which are subjected to heat).
2.
Do not undercoat the exhaust pipe or other parts which become hot.
3.
Do not undercoat rotating parts.
4.
Apply bitumen wax after applying undercoating.
5.
After putting seal on the vehicle, put undercoating on it.
SIIA2161E
BL-268
BODY REPAIR
Revision: 2005 August
2005 Murano
STONE GUARD COAT
To prevent damage caused by stones, the lower outer body panel (fender, door, etc.) have an additional layer
of Stone Guard Coating over the ED primer coating. When replacing or repairing these panels, apply Stone
Guard coating to the same portions as before. Use a coating which is rust preventive, durable, shock-resistant
and has a long shelf life.
SIIA2162E
BODY REPAIR
BL-269
C
D
E
F
G
H
J
K
L
M
A
B
BL
Revision: 2005 August
2005 Murano
Body Sealing
AIS001XW
DESCRIPTION
The following figure shows the areas which are sealed at the factory. Sealant which has been applied to these
areas should be smooth and free from cuts or gaps. Care should be taken not to apply an excess amount of
sealant and not to allow other unaffected parts to come into contact with the sealant.
SIIA2163E
BL-270
BODY REPAIR
Revision: 2005 August
2005 Murano
SIIA2164E
BODY REPAIR
BL-271
C
D
E
F
G
H
J
K
L
M
A
B
BL
Revision: 2005 August
2005 Murano
SIIA2165E
BL-272
BODY REPAIR
Revision: 2005 August
2005 Murano
Body Construction
AIS001XX
BODY CONSTRUCTION
SIIA2166E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст