Nissan Murano Z50 (2005 year). Manual — part 75
UNIFIED METER AND A/C AMP
DI-37
C
D
E
F
G
H
I
J
L
M
A
B
DI
Revision: 2005 August
2005 Murano
DTC [B2205] Vehicle Speed Circuit
AKS00D5J
Symptom: Display VEHICLE SPEED CIRC [B2205] at the result of self-diagnosis for unified meter and A/C
amp.
1.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS
Perform the ABS actuator and electric unit (control unit) self-diagnosis. Refer to
BRC-20, "CONSULT- II Functions"
(without VDC system).
Self-diagnostic results content
No malfunction detected >>Replace unified meter and A/C amp.
Malfunction detected >>Check applicable parts, and repair or replace corresponding parts.
Removal and Installation of Unified Meter and A/C Amp.
AKS00D5K
REMOVAL
1.
Remove the audio unit. Refer to
.
2.
Remove the fixing screws, then remove the unified meter and A/
C amp.
INSTALLATION
Installation is basically the reverse order of removal.
RJIA1813E
DI-38
COMPASS
Revision: 2005 August
2005 Murano
COMPASS
PFP:24835
System Description
AKS00ABY
This unit displays earth magnetism and heading direction of vehicle.
DIRECTION DISPLAY
Push the switch when the ignition key is in the “ON” or “START” position. The direction will be displayed.
Pushing the “COMP” switch a second time will turn off the display.
1.
If the display reads “C” calibrate the compass by driving the vehicle in 3 complete circles at less than 8
km/h (5 MPH).
2.
To adjust for compass variance:
a.
Press the “COMP” switch for more than 3 seconds. The current zone number will appear in the display.
b.
Find your current location and variance zone number on the zone map.
c.
Press the “COMP” switch until the new zone number appears in the display. After you stop pressing the
button in, the display will show a compass direction within a few seconds.
NOTE:
1. Do not install the ski rack, antenna, etc. which are attached to the vehicle by means of a magnet. They
affect the operation of the compass.
2. If the compass deviates from the correct indication soon after repeated adjustment, have the compass
checked at an authorized dealer.
3. The compass may not indicate the correct compass point in tunnels or while driving up or down a steep
hill. (The compass returns to the correct compass point when the vehicle moves to an area where the
geomagnetism is stabilized.)
3.
Cleaning the Mirror
When cleaning the mirror, use a paper towel or similar material dampened with glass cleaner. Do not
spray glass cleaner directly on the mirror as that may cause the liquid cleaner to enter the mirror housing.
SKIA5335E
COMPASS
DI-39
C
D
E
F
G
H
I
J
L
M
A
B
DI
Revision: 2005 August
2005 Murano
“C” is Displayed In the Compass Window
The compass needs to be calibrated. Drive the vehicle in 3 circles at 8 km/h (5 MPH) or less until the display
reads a direction. You can also calibrate the compass by driving your vehicle on your everyday routine. The
compass will be calibrated once it has tracked 3 complete circles.
Inaccurate Compass Direction
1.
With the display turned on, push the “COMP” switch for 3 sec-
onds, until the zone selection comes up (a number will be dis-
played in the mirror compass window).
2.
Toggle until correct zone is found and release switch.
3.
The display will show all segments, and return to the normal
compass mode within 10 seconds of no switch activity.
4.
If the vehicle changes zone, repeat steps 1 through 3. See map.
SEL168Y
DI-40
COMPASS
Revision: 2005 August
2005 Murano
Wiring Diagram – COMPASS –
AKS00ABZ
TKWA1428E
COMPASS
DI-41
C
D
E
F
G
H
I
J
L
M
A
B
DI
Revision: 2005 August
2005 Murano
Removal and Installation of Compass
AKS00AC0
Refer to
DI-42
WARNING LAMPS
Revision: 2005 August
2005 Murano
WARNING LAMPS
PFP:24814
Schematic
AKS00D5L
TKWB0482E
WARNING LAMPS
DI-43
C
D
E
F
G
H
I
J
L
M
A
B
DI
Revision: 2005 August
2005 Murano
Wiring Diagram — WARN —
AKS00D5M
TKWB0483E
DI-44
WARNING LAMPS
Revision: 2005 August
2005 Murano
TKWB0484E
WARNING LAMPS
DI-45
C
D
E
F
G
H
I
J
L
M
A
B
DI
Revision: 2005 August
2005 Murano
TKWB0485E
DI-46
WARNING LAMPS
Revision: 2005 August
2005 Murano
TKWB0486E
WARNING LAMPS
DI-47
C
D
E
F
G
H
I
J
L
M
A
B
DI
Revision: 2005 August
2005 Murano
TKWB0487E
DI-48
WARNING LAMPS
Revision: 2005 August
2005 Murano
TKWB0488E
WARNING LAMPS
DI-49
C
D
E
F
G
H
I
J
L
M
A
B
DI
Revision: 2005 August
2005 Murano
TKWB0489E
DI-50
WARNING LAMPS
Revision: 2005 August
2005 Murano
TKWB0490E
WARNING LAMPS
DI-51
C
D
E
F
G
H
I
J
L
M
A
B
DI
Revision: 2005 August
2005 Murano
Oil Pressure Warning Lamp Stays Off (Ignition Switch ON)
AKS00D5N
1.
CHECK SELF-DIAGNOSTIC RESULTS OF UNIFIED METER AND A/C AMP.
Select “METER A/C AMP” on CONSULT-II, and perform self-diagnosis of unified meter and A/C amp. Refer to
DI-31, "CONSULT-II Function (METER A/C AMP)"
Self-diagnostic results content
No malfunction detected>> GO TO 2.
Malfunction detected>> Go to
2.
CHECK IPDM E/R OUTPUT SIGNAL
Activate IPDM E/R auto active test. Refer to
.
Does oil pressure warning lamp blink?
YES
>> GO TO 5.
NO
>> GO TO 3.
3.
CHECK BCM INPUT SIGNAL
Select “DATA MONITOR” of “SIGNAL BUFFER”. Refer to
. Operate ignition switch with “OIL
PRESS SW” of “DATA MONITOR” and check operate status.
OK or NG
OK
>> GO TO 4.
NG
>> Replace IPDM E/R. Refer to
.
4.
CHECK UNIFIED METER AND A/C AMP. INPUT SIGNAL
Select “METER A/C AMP” on CONSULT-II. Operate ignition switch
with “OIL W/L” of “DATA MONITOR” and check operation status.
OK or NG
OK
>> Replace combination meter.
NG
>> Replace BCM. Refer to
BCS-16, "Removal and Installa-
“OIL PRESS SW”
When ignition switch is in ON
position (Engine stopped)
: ON
When engine running
: OFF
SKIA8709E
“OIL W/L”
When ignition switch is in ON
position (Engine stopped)
: ON
When engine running
: OFF
PKIA2064E
DI-52
WARNING LAMPS
Revision: 2005 August
2005 Murano
5.
CHECK OIL PRESSURE SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector and oil pressure switch connector.
3.
Check continuity between IPDM E/R harness connector E9 ter-
minal 57 (P/L) and oil pressure switch harness connector F203
terminal 1 (R/L).
OK or NG
OK
>> GO TO 6.
NG
>> Repair harness or connector.
6.
CHECK OIL PRESSURE SWITCH
Check oil pressure switch. Refer to
OK or NG
OK
PG-29, "Removal and Installation of IPDM E/R"
NG
>> Replace oil pressure switch.
Oil Pressure Warning Lamp Does Not Turn Off (Oil Pressure Is Normal)
AKS00D5O
NOTE:
For oil pressure inspection, refer to
1.
CHECK IPDM E/R OUTPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect oil pressure switch connector.
3.
Turn ignition switch ON.
4.
Check voltage between oil pressure switch harness connector
F203 terminal 1 (R/L) and ground.
OK or NG
OK
>> GO TO 2.
NG
>> GO TO 3.
2.
CHECK OIL PRESSURE SWITCH
1.
Turn ignition switch OFF.
2.
Check oil pressure switch. Refer to
OK or NG
OK
PG-29, "Removal and Installation of IPDM E/R"
NG
>> Replace oil pressure switch.
57 (P/L) – 1 (R/L)
: Continuity should exist.
PKIB3986E
1 (R/L) – Ground
: Approx. 12 V
PKIB3987E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст