Nissan Murano Z50 (2005 year). Manual — part 57
COOLING FAN
CO-21
C
D
E
F
G
H
I
J
K
L
M
A
CO
Revision: 2005 August
2005 Murano
Disassembly and Assembly
ABS00D9J
DISASSEMBLY
1.
Remove cooling fans (RH and LH) from fan motors.
2.
Remove fan motors from fan shroud.
INSPECTION AFTER DISASSEMBLY
Cooling Fan
Inspect cooling fan for crack or unusual bend.
●
If anything is found, replace cooling fan.
ASSEMBLY
Assemble in the reverse order of disassembly.
CAUTION:
Cooling fans and fan motors are different between RH and LH. Be careful not to misassemble them.
CO-22
WATER PUMP
Revision: 2005 August
2005 Murano
WATER PUMP
PFP:21020
Removal and Installation
ABS00353
CAUTION:
●
When removing water pump assembly, be careful not to get engine coolant on drive belt.
●
Water pump cannot be disassembled and should be replaced as a unit.
●
After installing water pump, connect hose and clamp securely, then check for leaks using the radi-
ator cap tester (commercial service tool) and the radiator cap tester adapter [SST: EG17650301
(J33984-A)].
REMOVAL
1.
Remove engine cover. Refer to
EM-18, "INTAKE MANIFOLD COLLECTOR"
.
2.
Remove air duct (inlet) and radiator cover grills (right and left sides). Refer to
3.
Remove undercover and splash guard (RH).
4.
Drain engine coolant from radiator. Refer to
CO-9, "Changing Engine Coolant"
CAUTION:
●
Perform this step when the engine is cold.
●
Do not spill engine coolant on drive belts.
5.
Remove drive belts. Refer to
.
6.
Remove reservoir tank of radiator. Refer to
7.
Remove reservoir tank of power steering oil pump with piping connected, and move it to aside. Refer to
.
8.
Support oil pan (lower) bottom with transmission jack.
9.
Remove RH engine mounting insulator and RH engine mounting bracket. Refer to
1.
Water pump
2.
Timing chain tensioner (primary)
3.
Chain tensioner cover
4.
Water drain plug (front)
5.
Water pump cover
6.
O-ring
7.
O-ring
PBIC2695E
WATER PUMP
CO-23
C
D
E
F
G
H
I
J
K
L
M
A
CO
Revision: 2005 August
2005 Murano
10. Remove water drain plug (front) on water pump side of cylinder
block to drain engine coolant from engine inside.
11. Remove chain tensioner cover and water pump cover from front timing chain case.
●
Use the seal cutter [SST: KV10111100 (J37228)] to cut liquid gasket for removal.
12. Remove idler pulley and bracket. Refer to
.
13. Remove timing chain tensioner (primary) as follows:
a.
Remove lower mounting bolt.
CAUTION:
Be careful not to drop mounting bolt inside timing chain
case.
b.
Loosen upper mounting bolt slowly, and then turn chain ten-
sioner (primary) on the mounting bolt so that plunger is fully
expanded.
NOTE:
Even if plunger is fully expanded, it is not dropped from the body
of timing chain tensioner (primary).
c.
Turn crankshaft pulley clockwise so that timing chain on the tim-
ing chain tensioner (primary) side is loose.
d.
Remove upper mounting bolt, and then remove timing chain ten-
sioner (primary).
CAUTION:
Be careful not to drop mounting bolt inside timing chain
case.
14. Remove water pump as follows:
PBIC2662E
PBIC3575E
PBIC1805E
PBIC3576E
CO-24
WATER PUMP
Revision: 2005 August
2005 Murano
a.
Remove three water pump mounting bolts. Secure a gap
between water pump gear and timing chain, by turning crank-
shaft pulley counterclockwise until timing chain looseness on
water pump sprocket becomes maximum.
b.
Screw M8 bolts [pitch: 1.25 mm (0.049 in) length: approx. 50
mm (1.97 in)] into water pumps upper and lower mounting bolt
holes until they reach timing chain case. Then, alternately
tighten each bolt for a half turn, and pull out water pump.
CAUTION:
●
Pull straight out while preventing vane from contacting
socket in installation area.
●
Remove water pump without causing sprocket to contact
timing chain.
c.
Remove M8 bolts and O-rings from water pump.
CAUTION:
Do not disassemble water pump.
INSPECTION AFTER REMOVAL
●
Check for badly rusted or corroded water pump body assembly.
●
Check for rough operation due to excessive end play.
●
If anything is found, replace water pump.
INSTALLATION
1.
Install new O-rings to water pump.
●
Apply engine oil and engine coolant to O-rings as shown in
the figure.
●
Locate O-ring with white paint mark to engine front side.
PBIC1193E
JLC357B
SLC943A
PBIC1397E
WATER PUMP
CO-25
C
D
E
F
G
H
I
J
K
L
M
A
CO
Revision: 2005 August
2005 Murano
2.
Install water pump.
CAUTION:
Do not allow cylinder block to nip O-rings when installing
water pump.
●
Check that timing chain and water pump sprocket are
engaged.
●
Insert water pump by tightening mounting bolts alternately
and evenly.
3.
Install timing chain tensioner (primary) as follows:
a.
Turn crankshaft pulley clockwise so that timing chain on the tim-
ing chain tensioner (primary) side is loose.
b.
Pull plunger stopper tab up (or turn lever downward) so as to
remove plunger stopper tab from the ratchet of plunger.
NOTE:
Plunger stopper tab and lever are synchronized.
c.
Push plunger into the inside of tensioner body.
d.
Hold plunger in the fully compressed position by engaging
plunger stopper tab with the tip of ratchet.
e.
To secure lever, insert stopper pin through hole of lever into ten-
sioner body hole.
●
The lever parts and the tab are synchronized. Therefore, the
plunger will be secured under this condition.
NOTE:
Figure shows the example of 1.2 mm (0.047 in) diameter thin screwdriver being used as the stopper pin.
f.
Install timing chain tensioner (primary).
●
Remove dust and foreign material completely from backside of timing chain tensioner (primary) and
from installation area of rear timing chain case.
g.
Remove stopper pin.
h.
Make sure again that timing chain and water pump sprocket are engaged.
4.
Install chain tensioner cover and water pump cover as follows:
SLC031B
PBIC1805E
PBIC3568E
PBIC3577E
CO-26
WATER PUMP
Revision: 2005 August
2005 Murano
a.
Before installing, remove all traces of old liquid gasket from mat-
ing surface of water pump cover and chain tensioner cover
using scraper. Also remove traces of old liquid gasket from the
mating surface of front timing chain case.
b.
Apply a continuous bead of liquid gasket with the tube presser
[SST: WS39930000 (
—
)] to mating surface of chain ten-
sioner cover and water pump cover.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-47, "RECOMMENDED CHEMICAL PRODUCTS AND
SEALANTS"
CAUTION:
Attaching should be done within 5 minutes after coating.
c.
Tighten mounting bolts.
5.
Install water drain plug (front) on water pump side of cylinder block.
●
Apply liquid gasket to the thread of water drain plug (front).
Use Genuine RTV Silicone Sealant or equivalent. Refer to
.
6.
Install in the reverse order of removal after this step.
●
After starting engine, let idle for three minutes, then rev engine up to 3,000 rpm under no load to
purge air from the high-pressure chamber of chain tensioner. Engine may produce a rattling
noise. This indicates that air still remains in the chamber and is not a matter of concern.
INSPECTION AFTER INSTALLATION
●
Check for leaks of engine coolant using the radiator cap tester adapter [SST: EG17650301 (J33984-A)]
and the radiator cap tester (commercial service tool). Refer to
.
●
Start and warm up the engine. Visually make sure that there is no leaks of engine coolant.
SLC446B
PBIC2663E
WATER INLET AND THERMOSTAT ASSEMBLY
CO-27
C
D
E
F
G
H
I
J
K
L
M
A
CO
Revision: 2005 August
2005 Murano
WATER INLET AND THERMOSTAT ASSEMBLY
PFP:21200
Removal and Installation
ABS00354
REMOVAL
1.
Drain engine coolant from radiator drain plug at the bottom of radiator, and from water drain plug at the
front of cylinder block. Refer to
CO-9, "Changing Engine Coolant"
.
CAUTION:
●
Perform this step when the engine is cold.
●
Do not spill engine coolant on drive belts.
2.
Remove reservoir tank of radiator, and move it aside.
3.
Disconnect radiator hose (lower) and oil cooler water hose from water inlet and thermostat assembly.
4.
Remove water inlet and thermostat assembly.
CAUTION:
Do not disassemble water inlet and thermostat assembly.
Replace them as a unit, if necessary.
1.
Gasket
2.
Water inlet and thermostat assembly
3.
Radiator hose (lower)
4.
Water hose
PBIC2696E
SLC962AB
CO-28
WATER INLET AND THERMOSTAT ASSEMBLY
Revision: 2005 August
2005 Murano
INSPECTION AFTER REMOVAL
1.
Check valve seating condition at ordinary room temperatures. It should seat tightly.
2.
Check valve operation.
●
If the malfunctioning condition, when valve seating at ordinary
room temperature, or measured values are out of the standard,
replace water inlet and thermostat assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
●
Be careful not to spill engine coolant over engine room. Use rag to absorb engine coolant.
INSPECTION AFTER INSTALLATION
●
Check for leaks of engine coolant using the radiator cap tester adapter [SST: EG17650301 (J33984-A)]
and the radiator cap tester (commercial service tool). Refer to
.
●
Start and warm up the engine. Visually make sure that there is no leaks of engine coolant.
Thermostat
Standard
Valve opening temperature
80.5 - 83.5
°
C (177 - 182
°
F)
Maximum valve lift
8.6 mm / 95
°
C (0.339 in / 203
°
F)
Valve closing temperature
77
°
C (171
°
F)
SLC949A
WATER OUTLET AND WATER PIPING
CO-29
C
D
E
F
G
H
I
J
K
L
M
A
CO
Revision: 2005 August
2005 Murano
WATER OUTLET AND WATER PIPING
PFP:11060
Removal and Installation
ABS0035E
REMOVAL
1.
EM-18, "INTAKE MANIFOLD COLLECTOR"
2.
Drain engine coolant from radiator drain plug at the bottom of radiator, and from water drain plug at the
front of cylinder block. Refer to
CO-9, "Changing Engine Coolant"
.
CAUTION:
●
Perform this step when the engine is cold.
●
Do not spill engine coolant on drive belts.
3.
Remove air duct (inlet), radiator cover grills (right and left sides), air cleaner case (upper) with mass air
flow sensor and air duct assembly. Refer to
EM-16, "AIR CLEANER AND AIR DUCT"
4.
Remove battery and battery tray. Refer to
SC-8, "Removal and Installation"
5.
Remove CVT fluid cooler control valve assembly. Refer to
.
6.
Move CVT control cable aside. Refer to
CVT-211, "SHIFT CONTROL SYSTEM"
.
7.
Remove radiator hose (upper).
8.
Remove water hoses and heater hoses.
9.
Disconnect harness connectors, and move harness to aside.
1.
Radiator hose (upper)
2.
Washer
3.
Engine coolant temperature sensor
4.
Heater hose
5.
Water outlet
6.
Water hose
7.
Gasket
8.
Water hose
9.
Gasket
10. Water connector
11.
O-ring
12. Heater pipe
13. Heater hose
14. Water bypass pipe
15. Water hose
PBIC4203E
CO-30
WATER OUTLET AND WATER PIPING
Revision: 2005 August
2005 Murano
10. Remove engine coolant temperature sensor as necessary.
CAUTION:
Be careful not to damage engine coolant temperature sensor.
11. Remove water outlet, heater pipe, water bypass pipe and water connector.
INSTALLATION
Note the following, and install in the reverse order of removal.
●
Securely insert each hose, and install clamp at a position where it does not interfere with the pipe bulge.
●
When inserting water bypass pipe and heater pipe into water connector, apply neutral detergent to O-ring.
INSPECTION AFTER INSTALLATION
●
Check for leaks of engine coolant using the radiator cap tester adapter [SST: EG17650301 (J33984-A)]
and the radiator cap tester (commercial service tool). Refer to
.
●
Start and warm up the engine. Visually make sure that there is no leaks of engine coolant.
SERVICE DATA AND SPECIFICATIONS (SDS)
CO-31
C
D
E
F
G
H
I
J
K
L
M
A
CO
Revision: 2005 August
2005 Murano
SERVICE DATA AND SPECIFICATIONS (SDS)
PFP:00100
Standard and Limit
ABS00E86
ENGINE COOLANT CAPACITY (APPROXIMATE)
Unit:
(US qt, Imp qt)
RADIATOR
Unit: kPa (kg/cm
2
, psi)
THERMOSTAT
Engine coolant capacity (With reservoir tank at “MAX” level)
9.6 (10-1/8, 8-1/2)
Reservoir tank engine coolant capacity (At “MAX” level)
0.8 (7/8, 3/4)
Cap relief pressure
Standard
78 - 98 (0.8 - 1.0, 11 - 14)
Limit
59 (0.6, 9)
Leakage testing pressure
157 (1.6, 23)
Thermostat
Standard
Valve opening temperature
80.5 - 83.5
°
C (177 - 182
°
F)
Maximum valve lift
8.6 mm / 95
°
C (0.339 in / 203
°
F)
Valve closing temperature
77
°
C (171
°
F)
CO-32
SERVICE DATA AND SPECIFICATIONS (SDS)
Revision: 2005 August
2005 Murano
CVT-1
CVT
C TRANSMISSION/TRANSAXLE
CONTENTS
D
E
F
G
H
I
J
K
L
M
SECTION
CVT
A
B
CVT
Revision: 2005 August
2005 Murano
CVT
INDEX FOR DTC . . . . . . . . . . . . . . 6
Alphabetical Index . . . . . . . . . . . . . 6
DTC No. Index . . . . . . . . . . . . . . . 7
PRECAUTIONS . . . . . . . . . . . . . . .. 8
OPERATION PROCEDURE . . . . . . . . . 8
Precautions for TCM and CVT Assembly Replace-
ment . . . . . . . . . . . . . . . . . . . 9
Removal and Installation Procedure for CVT Unit
Connector . . . . . . . . . . . . . . . ... 10
REMOVAL . . . . . . . . . . . . . . ... 10
INSTALLATION . . . . . . . . . . . . ... 10
Precautions . . . . . . . . . . . . . . . .11
Service Notice or Precautions . . . . . . . . 12
CVT FLUID COOLER SERVICE . . . . . . . 12
OBD-II SELF-DIAGNOSIS . . . . . . . . .. 12
PREPARATION . . . . . . . . . . . . . . . 13
Special Service Tools . . . . . . . . . . . . 13
Commercial Service Tools . . . . . . . . . .. 14
CVT FLUID . . . . . . . . . . . . . . . ... 15
Checking CVT Fluid . . . . . . . . . . . ... 15
FLUID LEVEL CHECK . . . . . . . . . . 15
Changing CVT Fluid . . . . . . . . . . . ... 16
CVT Fluid Cooler Cleaning . . . . . . . . . 17
CVT FLUID COOLER CLEANING PROCEDURE
DURE . . . . . . . . . . . . . . . . .. 19
CVT FLUID COOLER FINAL INSPECTION . . 19
CVT SYSTEM . . . . . . . . . . . . . . . 20
CONTROL SYSTEM OUTLINE . . . . . . .. 23
CONTROL SYSTEM DIAGRAM . . . . . . . 23
CAN Communication . . . . . . . . . . . .. 24
SYSTEM DESCRIPTION . . . . . . . . . 24
Input/Output Signal of TCM . . . . . . . . . 24
Line Pressure and Secondary Pressure Control . 25
NORMAL CONTROL . . . . . . . . . . .. 25
FEEDBACK CONTROL . . . . . . . . . .. 25
Shift Control . . . . . . . . . . . . . . . 25
Lock-up and Select Control . . . . . . . . . 27
TORQUE CONVERTER CLUTCH AND SELECT
CONTROL VALVE CONTROL . . . . . . . 27
Control Valve . . . . . . . . . . . . . . .. 28
FUNCTION OF CONTROL VALVE . . . . . . 28
ON BOARD DIAGNOSTIC (OBD) SYSTEM . . . 29
ONE TRIP DETECTION LOGIC . . . . . . . 29
TWO TRIP DETECTION LOGIC . . . . . . . 29
CVT-2
Revision: 2005 August
2005 Murano
HOW TO ERASE DTC (WITH GST) . . . . ... 31
Malfunction Indicator Lamp (MIL) . . . . . . ... 32
DESCRIPTION . . . . . . . . . . . . . 32
TROUBLE DIAGNOSIS . . . . . . . . . . . 33
DTC Inspection Priority Chart . . . . . . . . . 33
Fail-safe . . . . . . . . . . . . . . . . .. 33
FAIL-SAFE FUNCTION . . . . . . . . . ... 33
How to Perform Trouble Diagnosis for Quick and
Accurate Repair . . . . . . . . . . . . . .. 34
Road Test . . . . . . . . . . . . . . . ... 46
DESCRIPTION . . . . . . . . . . . . . 46
CONSULT-II SETTING PROCEDURE . . . . 46
TCM TERMINAL CONNECTOR LAYOUT . . .. 58
TCM INSPECTION TABLE . . . . . . . . .. 58
CONSULT-II Function (TRANSMISSION) . . . .. 61
Diagnostic Procedure Without CONSULT-II . . ... 73
OBD-II SELF-DIAGNOSTIC PROCEDURE
(WITH GST) . . . . . . . . . . . . . . . 73
DTC U1000 CAN COMMUNICATION LINE . . . .. 74
WITH CONSULT-II . . . . . . . . . . . .. 74
WITH GST . . . . . . . . . . . . . . ... 74
Wiring Diagram — CVT — CAN . . . . . . . . 75
Diagnostic Procedure . . . . . . . . . . . . 76
DTC P0615 START SIGNAL CIRCUIT . . . . . . 77
WITH CONSULT-II . . . . . . . . . . . .. 77
Wiring Diagram — CVT — STSIG . . . . . . ..78
Diagnostic Procedure . . . . . . . . . . . ..79
DTC P0703 STOP LAMP SWITCH CIRCUIT . . . 81
WITH CONSULT-II . . . . . . . . . . . ...81
Diagnostic Procedure . . . . . . . . . . . ..82
DTC P0705 PARK/NEUTRAL POSITION SWITCH ...83
WITH CONSULT-II . . . . . . . . . . . ...84
WITH GST . . . . . . . . . . . . . . ...84
PNP SWITCH . . . . . . . . . . . . . ..90
DTC P0710 CVT FLUID TEMPERATURE SENSOR
CIRCUIT . . . . . . . . . . . . . . . . . 91
WITH CONSULT-II . . . . . . . . . . . ...91
WITH GST . . . . . . . . . . . . . . ...91
CVT FLUID TEMPERATURE SENSOR . . . ..95
DTC P0715 INPUT SPEED SENSOR CIRCUIT (PRI
SPEED SENSOR) . . . . . . . . . . . . . .96
WITH CONSULT-II . . . . . . . . . . . ...96
WITH GST . . . . . . . . . . . . . . ...96
Wiring Diagram — CVT — PRSCVT . . . . . ..97
Diagnostic Procedure . . . . . . . . . . . ..98
DTC P0720 VEHICLE SPEED SENSOR CVT (SEC-
ONDARY SPEED SENSOR) . . . . . . . . ...101
WITH CONSULT-II . . . . . . . . . . . .101
WITH GST . . . . . . . . . . . . . . .101
Wiring Diagram — CVT — SESCVT . . . . . 102
Diagnostic Procedure . . . . . . . . . . . 103
CVT-3
D
E
F
G
H
I
J
K
L
M
A
B
CVT
Revision: 2005 August
2005 Murano
WITH CONSULT-II . . . . . . . . . . . 107
Diagnostic Procedure . . . . . . . . . . ... 107
DTC P0730 BELT DAMAGE . . . . . . . . .. 109
WITH CONSULT-II . . . . . . . . . . . 109
Diagnostic Procedure . . . . . . . . . . . 110
DTC P0740 TORQUE CONVERTER CLUTCH
SOLENOID VALVE . . . . . . . . . . . . .. 111
WITH CONSULT-II . . . . . . . . . . . . 111
WITH GST . . . . . . . . . . . . . . .. 111
TORQUE CONVERTER CLUTCH SOLENOID
VALVE . . . . . . . . . . . . . . . . 115
DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP) ..116
WITH CONSULT-II . . . . . . . . . . . .116
WITH GST . . . . . . . . . . . . . . ..116
Diagnostic Procedure . . . . . . . . . . . 117
DTC P0745 LINE PRESSURE SOLENOID VALVE
WITH CONSULT-II . . . . . . . . . . . .119
WITH GST . . . . . . . . . . . . . . ..119
PRESSURE CONTROL SOLENOID VALVE A
(LINE PRESSURE SOLENOID VALVE) . . ... 123
WITH CONSULT-II . . . . . . . . . . . 124
WITH GST . . . . . . . . . . . . . . . 124
Diagnostic Procedure . . . . . . . . . . ... 125
WITH CONSULT-II . . . . . . . . . . . 127
WITH GST . . . . . . . . . . . . . . . 127
Diagnostic Procedure . . . . . . . . . . ... 128
WITH CONSULT-II . . . . . . . . . . . 130
WITH GST . . . . . . . . . . . . . . . 130
PRESSURE CONTROL SORENOID VALVE B
(SECONDARY PRESSURE SOLENOID VALVE)
DTC P0826 MANUAL MODE SWITCH CIRCUIT ... 135
WITH CONSULT-II . . . . . . . . . . . 135
MANUAL MODE SWITCH . . . . . . . . 139
DTC P0840 TRANSMISSION FLUID PRESSURE
SENSOR A CIRCUIT (SEC PRESSURE SENSOR) .140
WITH CONSULT-II . . . . . . . . . . . 140
WITH GST . . . . . . . . . . . . . . . 140
Wiring Diagram — CVT — SECPS . . . . . .. 141
Diagnostic Procedure . . . . . . . . . . ... 142
DTC P0841 PRESSURE SENSOR FUNCTION . . 145
CVT-4
Revision: 2005 August
2005 Murano
DTC P0845 TRANSMISSION FLUID PRESSURE
SENSOR B CIRCUIT (PRI PRESSURE SENSOR) .148
WITH CONSULT-II . . . . . . . . . . . 148
WITH GST . . . . . . . . . . . . . . . 148
Wiring Diagram — CVT — PRIPS . . . . . . 149
Diagnostic Procedure . . . . . . . . . . ... 150
DTC P0868 SECONDARY PRESSURE DOWN . . 153
WITH CONSULT-II . . . . . . . . . . . 153
Diagnostic Procedure . . . . . . . . . . ... 154
DTC P1701 TRANSMISSION CONTROL MODULE
(POWER SUPPLY) . . . . . . . . . . . . .. 156
WITH CONSULT-II . . . . . . . . . . . 156
Wiring Diagram — CVT — POWER . . . . . . 157
Diagnostic Procedure . . . . . . . . . . ... 158
DTC P1705 THROTTLE POSITION SENSOR . ... 161
WITH CONSULT-II . . . . . . . . . . . 161
Diagnostic Procedure . . . . . . . . . . ... 162
DTC P1722 ESTM VEHICLE SPEED SIGNAL . ... 163
WITH CONSULT-II . . . . . . . . . . . 163
Diagnostic Procedure . . . . . . . . . . ... 164
DTC P1723 CVT SPEED SENSOR FUNCTION . . 165
WITH CONSULT-II . . . . . . . . . . . 165
Diagnostic Procedure . . . . . . . . . . ... 166
DTC P1726 ELECTRIC THROTTLE CONTROL
SYSTEM . . . . . . . . . . . . . . . . .. 167
WITH CONSULT-II . . . . . . . . . . . 167
Diagnostic Procedure . . . . . . . . . . ... 168
DTC P1740 LOCK-UP SELECT SOLENOID VALVE
CIRCUIT . . . . . . . . . . . . . . . . ..169
WITH CONSULT-II . . . . . . . . . . . .169
WITH GST . . . . . . . . . . . . . . .169
LOCK-UP SELECT SOLENOID VALVE . . . 173
DTC P1745 LINE PRESSURE CONTROL . . . .174
WITH CONSULT-II . . . . . . . . . . . .174
Diagnostic Procedure . . . . . . . . . . . 174
DTC P1777 STEP MOTOR - CIRCUIT . . . . . 175
WITH CONSULT-II . . . . . . . . . . . .175
WITH GST . . . . . . . . . . . . . . .175
STEP MOTOR . . . . . . . . . . . . ...178
DTC P1778 STEP MOTOR - FUNCTION . . . . 179
WITH CONSULT-II . . . . . . . . . . . .179
WITH GST . . . . . . . . . . . . . . .180
Diagnostic Procedure . . . . . . . . . . . 180
SECOND POSITION SWITCH . . . . . . . . 181
SECOND POSITION SWITCH . . . . . . ..184
CVT INDICATOR CIRCUIT . . . . . . . . . ..185
CVT INDICATOR SYMPTOM CHART . . . ...185
TROUBLE DIAGNOSIS FOR SYMPTOMS . . . 186
Wiring Diagram — CVT — NONDTC . . . . ...186
CVT Indicator Lamp Does Not Come On . . . ..190
SYMPTOM: . . . . . . . . . . . . . . 190
DIAGNOSTIC PROCEDURE . . . . . . . .190
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст