Nissan Murano Z50 (2005 year). Manual — part 11
REFRIGERANT LINES
ATC-137
C
D
E
F
G
H
I
K
L
M
A
B
ATC
Revision: 2005 August
2005 Murano
Inspection
Clutch disc
If the contact surface shows signs of damage due to excessive heat,
replace clutch disc and pulley.
Pulley
Check appearance of pulley assembly. If contact surface of pulley
shows signs of excessive grooving, replace clutch disc and pulley.
Contact surfaces of pulley assembly should be cleaned with a suit-
able solvent before reinstallation.
Coil
Check coil for loose connection or cracked insulation.
INSTALLATION
1.
Install field coil.
Be sure to align coil’s pin with the hole in the compressor’s front
head.
2.
Install compressor connector.
3.
Install pulley assembly using pulley installer (SST) and a hand
press, and then install snap ring using a snap ring pliers.
4.
Using holder to prevent clutch disc rotation.
After tightening bolt, make sure pulley rotates smoothly.
RJIA1883E
RHA142E
RJIA1884E
Tightening torque
: 14 N·m (1.4 kg-m,10 ft-lb)
RJIA1885E
ATC-138
REFRIGERANT LINES
Revision: 2005 August
2005 Murano
5.
Check clearance around entire periphery of clutch disc.
If the specified clearance is not obtained, replace adjusting
spacer and readjust.
Break-in Operation
When replacing compressor clutch assembly, always carry out break-in operation. This is done by engaging
and disengaging clutch about thirty-times. Break-in operation raises the level of transmitted torque.
Disc to pulley
clearance
: 0.3 - 0.60 mm (0.012 - 0.024 in)
RJIA1886E
REFRIGERANT LINES
ATC-139
C
D
E
F
G
H
I
K
L
M
A
B
ATC
Revision: 2005 August
2005 Murano
Removal and Installation of Low-pressure Flexible Hose
AJS00109
REMOVAL
1.
Use a refrigerant collecting equipment (for HFC-134a) to discharge the refrigerant.
2.
Remove cowl top cover. Refer to
3.
Remove air duct (inlet). Refer to
EM-16, "AIR CLEANER AND AIR DUCT"
4.
Remove mounting bolt from low-pressure flexible hose. (Com-
pressor side)
5.
Remove mounting bolt from low-pressure flexible hose.
6.
Remove low-pressure flexible hose.
CAUTION:
Cap or wrap the joint of the pipe with suitable material such
as vinyl tape to avoid the entry of air.
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
●
Replace O-rings of A/C piping with new ones, and then apply compressor oil to it when installing
it.
●
When recharging refrigerant, check for leaks.
RJIA2986E
RJIA1851E
ATC-140
REFRIGERANT LINES
Revision: 2005 August
2005 Murano
Removal and Installation of High-pressure Flexible Hose
AJS0010S
REMOVAL
1.
Use a refrigerant collecting equipment (for HFC-134a) to discharge the refrigerant.
2.
Remove air duct (inlet). Refer to
EM-16, "AIR CLEANER AND AIR DUCT"
3.
Remove mounting bolt from high-pressure flexible hose (Com-
pressor side), and then remove high-pressure flexible hose
mounting clip.
4.
Remove mounting nut from high-pressure flexible hose (Con-
denser side), and then remove high-pressure flexible hose.
CAUTION:
Cap or wrap the joint of the pipe with suitable material such
as vinyl tape to avoid the entry of air.
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
●
Replace O-rings of high-pressure flexible hose with new ones, and then apply compressor oil to it
when installing it.
●
When recharging refrigerant, check for leaks.
RJIA2988E
RJIA1853E
REFRIGERANT LINES
ATC-141
C
D
E
F
G
H
I
K
L
M
A
B
ATC
Revision: 2005 August
2005 Murano
Removal and Installation of Low-pressure Pipe 1 (Engine Compartment)
AJS0010B
REMOVAL
1.
Use a refrigerant collecting equipment (for HFC-134a) to discharge the refrigerant.
2.
Remove cowl top cover. Refer to
3.
Remove mounting bolt from low-pressure pipe 1 and low-pres-
sure pipe 1 bracket.
4.
Remove high-pressure pipe 1 from clip.
5.
Disconnect one-touch joints.
a.
Set a disconnector (SST: 9253089916) on A/C piping.
b.
Slide a disconnector toward vehicle front until it clicks.
c.
Slide A/C piping toward vehicle front and disconnect it.
6.
Remove low-pressure pipe 1.
CAUTION:
Cap or wrap the joint of the pipe with suitable material such
as vinyl tape to avoid the entry of air.
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
●
Replace O-rings of low-pressure pipe 1 with new ones, and then apply compressor oil to it when
installing it.
●
Connection point for female-side piping is thin. So, when inserting male-side piping, take care not
to deform female-side piping. Slowly insert in axial direction.
●
Insert one-touch joint connection point securely until it clicks.
●
After piping has been connected, pull male-side piping by hand to make sure piping does not
come off.
●
When recharging refrigerant, check for leaks.
RJIA1854E
RJIA1815E
Low-pressure pipe 1 bracket mounting bolt
Tightening torque
: 4.2 N·m (0.43 kg-m, 37 in-lb)
ATC-142
REFRIGERANT LINES
Revision: 2005 August
2005 Murano
Removal and Installation of High-pressure Pipe 1 (Engine Compartment)
AJS0010T
REMOVAL
1.
Remove air duct (inlet). Refer to
EM-16, "AIR CLEANER AND AIR DUCT"
2.
Remove low-pressure pipe 1. Refer to
ATC-141, "Removal and Installation of Low-pressure Pipe 1
3.
Remove radiator reservoir tank. Refer to
.
4.
Remove IPDM E/R. Refer to
PG-29, "Removal and Installation of IPDM E/R"
5.
Remove power steering oil tank mounting nuts.
6.
Remove vehicle harness connector from bracket.
7.
Remove high-pressure pipe 1 from clips.
8.
Remove high-pressure flexible hose from vehicle clips.
9.
Disconnect cooling fan connector.
10. Remove cooling fan harness clips from fan shroud.
11. Remove ground harness terminal mounting bolt.
12. Disconnect one-touch joint of high-pressure pipe 1.
a.
Set a disconnector (SST: 9253089908) on A/C piping.
b.
Slide a disconnector toward vehicle front until it clicks.
c.
Slide A/C piping toward vehicle front and disconnect it.
CAUTION:
Cap or wrap the joint of the pipe with suitable material such
as vinyl tape to avoid the entry of air.
13. Remove mounting bolt, and then remove high-pressure pipe 1.
CAUTION:
Cap or wrap the joint of the pipe with suitable material such
as vinyl tape to avoid the entry of air.
RJIA1856E
RJIA1857E
RJIA1855E
RJIA1853E
REFRIGERANT LINES
ATC-143
C
D
E
F
G
H
I
K
L
M
A
B
ATC
Revision: 2005 August
2005 Murano
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
●
Replace O-rings of high-pressure pipe 1 with new ones, and then apply compressor oil to it when
installing it.
●
Connection point for female-side piping is thin. So, when inserting male-side piping, take care not
to deform female-side piping. Slowly insert in axial direction.
●
Insert one-touch joint connection point securely until it clicks.
●
After piping has been connected, pull male-side piping by hand to make sure piping does not
come off.
●
When recharging refrigerant, check for leaks.
Removal and Installation of Low-pressure Pipe 2 and High-pressure Pipe 2
AJS0010D
REMOVAL
1.
Set the temperature control dial (passenger side) at 18
°
C (60
°
F), and then disconnect the battery cable
from negative terminal.
2.
Use a refrigerant collecting equipment (for HFC-134a) to discharge the refrigerant.
3.
Remove cowl top cover. Refer to
4.
Remove mounting bolt from low-pressure flexible pipe 1 bracket.
5.
Remove high-pressure pipe 1 from vehicle clips.
6.
Disconnect one-touch joints.
a.
Set a disconnector [high-pressure side (SST: 9253089908), low-
pressure side (SST: 9253089916)] on A/C piping.
b.
Slide a disconnector toward vehicle front until it clicks.
c.
Slide A/C piping toward vehicle front and disconnect it.
CAUTION:
Cap or wrap the joint of the pipe with suitable material such
as vinyl tape to avoid the entry of air.
7.
Remove blower unit. Refer to
8.
Remove air mix door motor (passenger side), foot duct, heater
core cover and evaporator cover.
RJIA1858E
RJIA1815E
RJIA1816E
ATC-144
REFRIGERANT LINES
Revision: 2005 August
2005 Murano
9.
Remove mounting bolt, and then remove low-pressure pipe 2
and high-pressure pipe 2.
CAUTION:
Cap or wrap the joint of the pipe with suitable material such
as vinyl tape to avoid the entry of air.
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
●
Replace O-rings of A/C piping with new ones, and then apply compressor oil to it when installing
it.
●
Connection point for female-side piping is thin. So, when inserting male-side piping, take care not
to deform female-side piping. Slowly insert in axial direction.
●
Insert one-touch joint connection point securely until it clicks.
●
After piping has been connected, pull male-side piping by hand to make sure piping does not
come off.
●
When recharging refrigerant, check for leaks.
RJIA1817E
Low-pressure pipe 1 bracket mounting bolt.
Tightening torque
: 4.2 N·m (0.43 kg-m, 37 in-lb)
REFRIGERANT LINES
ATC-145
C
D
E
F
G
H
I
K
L
M
A
B
ATC
Revision: 2005 August
2005 Murano
Removal and Installation of Liquid Tank
AJS0010E
REMOVAL
1.
Remove condenser. Refer to
ATC-146, "Removal and Installation of Condenser"
.
2.
Clean liquid tank and its surrounding area, and remove dirt and rust from tank.
CAUTION:
Be sure to clean carefully.
3.
Remove mounting bolts from liquid tank.
4.
Lift liquid tank bracket upward. Remove bracket from protruding
part of condenser.
5.
Slide liquid tank upward, and then remove liquid tank.
INSTALLATION
Install liquid tank, and then install liquid tank bracket on condenser.
CAUTION:
●
Make sure liquid tank bracket is securely installed at protru-
sion of condenser. (Make sure liquid tank bracket does not
move to a position below center of liquid tank.)
●
Replace O-rings of A/C piping with new ones, and then
apply compressor oil to it when installing it.
●
When recharging refrigerant, check for leaks.
RJIA1859E
RJIA1860E
RJIA1861E
Liquid tank bracket mounting bolt (upper side)
Tightening torque
: 3.4 N·m (0.34 kg-m, 30 in-lb)
Liquid tank bracket mounting bolt (lower side)
Tightening torque
: 5.7 N·m (0.58 kg-m, 50 in-lb)
ATC-146
REFRIGERANT LINES
Revision: 2005 August
2005 Murano
Removal and Installation of Condenser
AJS0010U
REMOVAL
1.
Use a refrigerant collecting equipment (for HFC-134a) to discharge the refrigerant.
2.
Remove air duct (inlet). Refer to
EM-16, "AIR CLEANER AND AIR DUCT"
3.
Remove engine undercover, using power tools.
4.
Drain engine coolant. Refer to
CO-9, "Changing Engine Coolant"
5.
Remove cooling fan shroud after removing radiator upper hose. Refer to
6.
Remove mounting bolt, and then disconnect high-pressure flexi-
ble hose and high-pressure pipe 1.
CAUTION:
Cap or wrap the joint of the pipe with suitable material such
as vinyl tape to avoid the entry of air.
7.
Remove radiator upper mount, move radiator and condenser to
the engine side.
8.
Remove mounting bolts, and then remove condenser.
CAUTION:
Be careful not to damage core surface of condenser and
radiator.
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
●
Replace O-rings of A/C piping with new ones, and then apply compressor oil to it when installing
it.
●
When recharging refrigerant, check for leaks.
RJIA1853E
RJIA1862E
Condenser mounting bolt
Tightening torque
: 6.1 N·m (0.62 kg-m, 54 in-lb)
REFRIGERANT LINES
ATC-147
C
D
E
F
G
H
I
K
L
M
A
B
ATC
Revision: 2005 August
2005 Murano
Removal and Installation of Refrigerant Pressure Sensor
AJS0010G
REMOVAL
1.
Remove condenser. Refer to
ATC-146, "Removal and Installation of Condenser"
.
2.
Remove refrigerant pressure sensor from condenser.
CAUTION:
When working, be careful not to damage the condenser.
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
●
Apply compressor oil to the O-ring of the refrigerant pressure sensor when installing it.
●
When recharging refrigerant, check for leaks.
Removal and Installation of Evaporator
AJS0010V
REMOVAL
1.
Remove low-pressure pipe 2 and high-pressure pipe 2. Refer to
ATC-143, "Removal and Installation of
Low-pressure Pipe 2 and High-pressure Pipe 2"
.
CAUTION:
Cap or wrap the joint of the pipe with suitable material such as vinyl tape to avoid the entry of air.
2.
Slide evaporator, and then remove it from heater & cooling unit
assembly.
3.
Remove intake sensor from evaporator, and then remove evap-
orator.
RJIA1863E
Refrigerant pressure sensor
Tightening torque
: 10.8 N·m (1.1 kg-m, 8.0 ft-lb)
RJIA1808E
ATC-148
REFRIGERANT LINES
Revision: 2005 August
2005 Murano
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
●
Replace O-rings of A/C piping with new ones, and then apply compressor oil to it when installing
it.
●
Connection point for female-side piping is thin. So, when inserting male-side piping, take care not
to deform female-side piping. Slowly insert in axial direction.
●
Insert one-touch joint connection point securely until it clicks.
●
After piping has been connected, pull male-side piping by hand to make sure piping does not
come off.
●
O-rings are different from low-pressure pipe 1 (high-pressure pipe 1) and low-pressure pipe 2
(high-pressure pipe 2).
●
Mark the mounting position of the intake sensor bracket prior to removal so that the reinstalled
sensor can be located in the same position.
●
When recharging refrigerant, check for leaks.
Removal and Installation of Expansion Valve
AJS0010W
REMOVAL
1.
Remove evaporator. Refer to
ATC-147, "Removal and Installation of Evaporator"
.
2.
Remove mounting bolts from expansion valve, and then remove
expansion valve.
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
●
Replace O-rings of evaporator with new ones, and then apply compressor oil to it when installing
it.
●
Connection point for female-side piping is thin. So, when inserting male-side piping, take care not
to deform female-side piping. Slowly insert in axial direction.
●
Insert one-touch joint connection point securely until it clicks.
●
After piping has been connected, pull male-side piping by hand to make sure piping does not
come off.
●
O-rings are different from low-pressure pipe 1 (high-pressure pipe 1) and low-pressure pipe 2
(high-pressure pipe 2).
●
When recharging refrigerant, check for leaks.
Low-pressure pipe 1 bracket mounting bolt
Tightening torque
: 4.2 N·m (0.43 kg-m, 37 in-lb)
RJIA1864E
Expansion valve mounting bolt
Tightening torque
: 3.9 N·m (0.4 kg-m, 35 in-lb)
REFRIGERANT LINES
ATC-149
C
D
E
F
G
H
I
K
L
M
A
B
ATC
Revision: 2005 August
2005 Murano
Checking for Refrigerant Leaks
AJS0010J
Perform a visual inspection of all refrigeration parts, fittings, hoses and components for signs of A/C lubricant
leakage, damage and corrosion. A/C lubricant leakage may indicate an area of refrigerant leakage. Allow
extra inspection time in these areas when using either an electronic refrigerant leak detector or fluorescent
dye leak detector (SST: J-42220).
If dye is observed, confirm the leak with an electronic refrigerant leak detector. It is possible a prior leak was
repaired and not properly cleaned.
When searching for leaks, do not stop when one leak is found but continue to check for additional leaks at all
system components and connections.
When searching for refrigerant leaks using an electronic leak detector, move the probe along the suspected
leak area at 1 to 2 inches per second and no further than 1/4 inch from the component.
CAUTION:
Moving the electronic leak detector probe slower and closer to the suspected leak area will improve
the chances of finding a leak.
Checking System for Leaks Using the Fluorescent Leak Detector
AJS0010K
1.
Check A/C system for leaks using the UV lamp and safety goggles (SST: J-42220) in a low sunlight area
(area without windows preferable). Illuminate all components, fittings and lines. The dye will appear as a
bright green/yellow area at the point of leakage. Fluorescent dye observed at the evaporator drain open-
ing indicates an evaporator core assembly (tubes, core or expansion valve) leak.
2.
If the suspected area is difficult to see, use an adjustable mirror or wipe the area with a clean shop rag or
cloth, with the UV lamp for dye residue.
3.
After the leak is repaired, remove any residual dye using dye cleaner (SST: J-43872) to prevent future
misdiagnosis.
4.
Perform a system performance check and verify the leak repair with an approved electronic refrigerant
leak detector.
NOTE:
Other gases in the work area or substances on the A/C components, for example, anti-freeze, windshield
washer fluid, solvents and lubricants, may falsely trigger the leak detector. Make sure the surfaces to be
checked are clean.
Clean with a dry cloth or blow off with shop air.
Do not allow the sensor tip of the detector to contact with any substance. This can also cause false readings
and may damage the detector.
Dye Injection
AJS0010L
(This procedure is only necessary when recharging the system or when the compressor has seized and was
replaced.)
1.
Check A/C system static (at rest) pressure. Pressure must be at least 345 kPa (3.52 kg/cm
2
, 50 psi).
2.
Pour one bottle (1/4 ounce / 7.4 cc) of the A/C refrigerant dye into the injector tool (SST: J-41459).
3.
Connect the injector tool to the A/C LOW PRESSURE side service fitting.
4.
Start engine and switch A/C ON.
5.
When the A/C operating (compressor running), inject one bottle (1/4 ounce / 7.4 cc) of fluorescent dye
through the low-pressure service valve using dye injector tool (SST: J-41459) (refer to the manufacture’s
operating instructions).
6.
With the engine still running, disconnect the injector tool from the service fitting.
CAUTION:
Be careful the A/C system or replacing a component, pour the dye directly into the open system
connection and proceed with the service procedures.
7.
Operate the A/C system for a minimum of 20 minutes to mix the dye with the system oil. Depending on the
leak size, operating conditions and location of the leak, it may take from minutes to days for the dye to
penetrate a leak and become visible.
8.
Attach a blue label as necessary.
ATC-150
REFRIGERANT LINES
Revision: 2005 August
2005 Murano
Electronic Refrigerant Leak Detector
AJS0010M
PRECAUTIONS FOR HANDLING LEAK DETECTOR
When performing a refrigerant leak check, use an A/C electrical leak
detector (SST) or equivalent. Ensure that the instrument is calibrated
and set properly per the operating instructions.
The leak detector is a delicate device. In order to use the leak detec-
tor properly, read the operating instructions and perform any speci-
fied maintenance.
1.
Position probe approximately 5 mm (3/16 in) away from point to
be checked.
2.
When testing, circle each fitting completely with probe.
3.
Move probe along component approximately 25 to 50 mm (1 to
2 in)/sec.
SHA196FA
SHA707EA
SHA706E
SHA708EA
REFRIGERANT LINES
ATC-151
C
D
E
F
G
H
I
K
L
M
A
B
ATC
Revision: 2005 August
2005 Murano
CHECKING PROCEDURE
To prevent inaccurate or false readings, make sure there is no refrigerant vapor, shop chemicals, or cigarette
smoke in the vicinity of the vehicle. Perform the leak test in calm area (low air/wind movement) so that the
leaking refrigerant is not dispersed.
1.
Stop engine.
2.
Connect a suitable A/C manifold gauge set (SST: J-39183) to the A/C service valves.
3.
Check if the A/C refrigerant pressure is at least 345 kPa (3.52 kg/cm
2
, 50 psi) above 16
°
C (61
°
F). If less
than specification, recover/evacuate and recharge the system with the specified amount of refrigerant.
NOTE:
At temperatures below 16
°
C (61
°
F), leaks may not be detected since the system may not reach 345 kPa
(3.52 kg/cm
2
, 50 psi).
4.
Perform the leak test from the high-pressure side (compressor discharge a to evaporator inlet g) to the
low-pressure side (evaporator drain hose h to shaft seal m). Refer to
. Perform a
leak check for the following areas carefully. Clean the component to be checked and move the leak
detected probe completely around the connection/component.
Compressor
Check the fitting of high- and low-pressure flexible hoses, relief valve and shaft seal.
Condenser
Check the fitting of high-pressure flexible hose and pipe, refrigerant pressure sensor.
Liquid tank
Check the fitting of refrigerant connection.
Service valves
Check all around the service valves. Ensure service valve caps are secured on the service valves (to pre-
vent leaks).
NOTE:
After removing A/C manifold gauge set from service valves, wipe any residue from valves to prevent any
false readings by leak detector.
Cooling unit (Evaporator)
With engine OFF, turn blower fan on “High” for at least 15 seconds to dissipate any refrigerant trace in the
cooling unit. Wait a minimum of 10 minutes accumulation time (refer to the manufacturer’s recommended
procedure for actual wait time) before inserting the leak detector probe into the drain hose.
Keep the probe inserted for at least 10 seconds. Use caution not to contaminate the probe tip with water
or dirt that may be in the drain hose.
5.
If a leak detector detects a leak, verify at least once by blowing compressed air into area of suspected
leak, then repeat check as outlined above.
6.
Do not stop when one leak is found. Continue to check for additional leaks at all system components.
If no leaks are found, perform steps 7 - 10.
7.
Start engine.
8.
Set the heater A/C control as follows;
a.
A/C switch: ON
b.
MODE switch: VENT (Ventilation)
c.
Intake door position: Recirculation
d.
Temperature control dial: Max cold
e.
Fan speed: High
9.
Run engine at 1,500 rpm for at least 2 minutes.
ATC-152
REFRIGERANT LINES
Revision: 2005 August
2005 Murano
10. Stop engine and perform leak check again following steps 4
through 6 above.
Refrigerant leaks should be checked immediately after stopping
the engine. Begin with the leak detector at the compressor. The
pressure on the high-pressure side will gradually drop after
refrigerant circulation stops and pressure on the low-pressure
side will gradually rise, as shown in the graph. Some leaks are
more easily detected when pressure is high.
11. Before connecting recovery/recycling recharging equipment to
vehicle, check recovery/recycling recharging equipment gauges.
No refrigerant pressure should be displayed. If pressure is dis-
played, recover refrigerant from equipment lines and then check
refrigerant purity.
12. Confirm refrigerant purity in supply tank using recovery/recycling recharging equipment and refrigerant
identifier.
13. Confirm refrigerant purity in vehicle A/C system using recovery/recycling recharging equipment and refrig-
erant identifier.
14. Discharge A/C system using approved refrigerant recovery equipment. Repair the leaking fitting or com-
ponent if necessary.
15. Evacuate and recharge A/C system and perform the leak test to confirm no refrigerant leaks.
16. Perform A/C performance test to ensure system works properly.
SHA839E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст