Nissan Murano Z50 (2005 year). Manual — part 170
CAN SYSTEM (TYPE 8)
LAN-333
[CAN]
C
D
E
F
G
H
I
J
L
M
A
B
LAN
Revision: 2005 August
2005 Murano
2.
CHECK HARNESS FOR SHORT CIRCUIT
1.
Disconnect following connectors.
–
ECM connector
–
Intelligent Key unit connector
–
Harness connector M82
–
BCM connector
–
Display control unit connector
–
Unified meter and A/C amp. connector
–
Harness connector M9
2.
Check continuity between data link connector M24 terminals 6
(L) and 14 (Y).
OK or NG
OK
>> GO TO 3.
NG
>> Check the following harnesses. If any harness is dam-
aged, repair the harness.
●
Harness between data link connector and ECM
●
Harness between data link connector and Intelligent
Key unit
●
Harness between data link connector and harness connector M82
●
Harness between data link connector and BCM
●
Harness between data link connector and display control unit
●
Harness between data link connector and unified meter and A/C amp.
●
Harness between data link connector and harness connector M9
3.
CHECK HARNESS FOR SHORT CIRCUIT
Check continuity between data link connector M24 terminals 6 (L),
14 (Y) and ground.
OK or NG
OK
>> GO TO 4.
NG
>> Check the following harnesses. If any harness is dam-
aged, repair the harness.
●
Harness between data link connector and ECM
●
Harness between data link connector and Intelligent
Key unit
●
Harness between data link connector and harness connector M82
●
Harness between data link connector and BCM
●
Harness between data link connector and display control unit
●
Harness between data link connector and unified meter and A/C amp.
●
Harness between data link connector and harness connector M9
6 (L) - 14 (Y)
: Continuity should not exist.
SKIA6868E
6 (L) - Ground
: Continuity should not exist.
14 (Y) - Ground
: Continuity should not exist.
PKIB5318E
LAN-334
[CAN]
CAN SYSTEM (TYPE 8)
Revision: 2005 August
2005 Murano
4.
CHECK HARNESS FOR SHORT CIRCUIT
1.
Disconnect TCM connector.
2.
Check continuity between TCM harness connector F103 termi-
nals 5 (L) and 6 (Y).
OK or NG
OK
>> GO TO 5.
NG
>> Repair harness between TCM and harness connector
F102.
5.
CHECK HARNESS FOR SHORT CIRCUIT
Check continuity between TCM harness connector F103 terminals 5
(L), 6 (Y) and ground.
OK or NG
OK
>> GO TO 6.
NG
>> Repair harness between TCM and harness connector
F102.
6.
CHECK HARNESS FOR SHORT CIRCUIT
1.
Disconnect harness connector B4 and harness connector B9.
2.
Check continuity between harness connector B4 terminals 4 (L)
and 10 (Y).
OK or NG
OK
>> GO TO 7.
NG
>> Check the following harnesses. If any harness is dam-
aged, repair the harness.
●
Harness between harness connector B4 and harness
connector B2
●
Harness between harness connector B4 and harness
connector B9
5 (L) - 6 (Y)
: Continuity should not exist.
PKIB5313E
5 (L) - Ground
: Continuity should not exist.
6 (Y) - Ground
: Continuity should not exist.
PKIB5319E
4 (L) - 10 (Y)
: Continuity should not exist.
PKIB5320E
CAN SYSTEM (TYPE 8)
LAN-335
[CAN]
C
D
E
F
G
H
I
J
L
M
A
B
LAN
Revision: 2005 August
2005 Murano
7.
CHECK HARNESS FOR SHORT CIRCUIT
Check continuity between harness connector B4 terminals 4 (L), 10
(Y) and ground.
OK or NG
OK
>> GO TO 8.
NG
>> Check the following harnesses. If any harness is dam-
aged, repair the harness.
●
Harness between harness connector B4 and harness
connector B2
●
Harness between harness connector B4 and harness connector B9
8.
CHECK HARNESS FOR SHORT CIRCUIT
1.
Disconnect driver seat control unit connector.
2.
Check continuity between driver seat control unit harness con-
nector B303 terminals 3 (L/Y) and 19 (BR/W).
OK or NG
OK
>> GO TO 9.
NG
>> Repair harness between driver seat control unit and har-
ness connector B301.
9.
CHECK HARNESS FOR SHORT CIRCUIT
Check continuity between driver seat control unit harness connector
B303 terminals 3 (L/Y), 19 (BR/W) and ground.
OK or NG
OK
>> GO TO 10.
NG
>> Repair harness between driver seat control unit and har-
ness connector B301.
4 (L) - Ground
: Continuity should not exist.
10 (Y) - Ground
: Continuity should not exist.
PKIB5321E
3 (L/Y) - 19 (BR/W)
: Continuity should not exist.
PKIB5315E
3 (L/Y) - Ground
: Continuity should not exist.
19 (BR/W) - Ground
: Continuity should not exist.
PKIB5322E
LAN-336
[CAN]
CAN SYSTEM (TYPE 8)
Revision: 2005 August
2005 Murano
10.
CHECK HARNESS FOR SHORT CIRCUIT
1.
Disconnect following connectors.
–
AWD control unit connector
–
ABS actuator and electric unit (control unit) connector
–
IPDM E/R connector
2.
Check continuity between IPDM E/R harness connector E9 ter-
minals 48 (L) and 49 (Y).
OK or NG
OK
>> GO TO 11.
NG
>> Check the following harnesses. If any harness is dam-
aged, repair the harness.
●
Harness between IPDM E/R and AWD control unit
●
Harness between IPDM E/R and ABS actuator and
electric unit (control unit)
●
Harness between IPDM E/R and harness connector E105
11.
CHECK HARNESS FOR SHORT CIRCUIT
Check continuity between IPDM E/R harness connector E9 termi-
nals 48 (L), 49 (Y) and ground.
OK or NG
OK
>> GO TO 12.
NG
>> Check the following harnesses. If any harness is dam-
aged, repair the harness.
●
Harness between IPDM E/R and AWD control unit
●
Harness between IPDM E/R and ABS actuator and
electric unit (control unit)
●
Harness between IPDM E/R and harness connector E105
12.
CHECK ECM AND IPDM E/R INTERNAL CIRCUIT
1.
Remove ECM and IPDM E/R from vehicle.
2.
Check resistance between ECM terminals 94 and 86.
3.
Check resistance between IPDM E/R terminals 48 and 49.
OK or NG
OK
>> GO TO 13.
NG
>> Replace ECM and/or IPDM E/R.
48 (L) - 49 (Y)
: Continuity should not exist.
PKIB5317E
48 (L) - Ground
: Continuity should not exist.
49 (Y) - Ground
: Continuity should not exist.
PKIB5323E
94 - 86
: Approx. 108 – 132
Ω
48 - 49
: Approx. 108 – 132
Ω
LKIA0037E
CAN SYSTEM (TYPE 8)
LAN-337
[CAN]
C
D
E
F
G
H
I
J
L
M
A
B
LAN
Revision: 2005 August
2005 Murano
13.
CHECK SYMPTOM
1.
Fill in described symptoms on the column “Symptom” in the check sheet.
2.
Connect all the connectors, and then make sure that the symptom is reproduced.
OK or NG
OK
>> GO TO 14.
NG
>> Refer to
LAN-17, "Example of Filling in Check Sheet When Initial Conditions Are Not Reproduced"
.
14.
CHECK UNIT REPRODUCIBILITY
Perform the following procedure for each unit, and then perform reproducibility test.
1.
Turn ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Disconnect the unit connector.
4.
Connect the battery cable to the negative terminal.
5.
Make sure that the symptom filled in the “Symptom” of the check sheet is reproduced. (Do not confuse it
with the symptom related to removed unit.)
6.
Make sure that the same symptom is reproduce.
–
Intelligent Key unit
–
TCM
–
BCM
–
Display control unit
–
Unified meter and A/C amp.
–
Driver seat control unit
–
AWD control unit
–
ABS actuator and electric unit (control unit)
–
ECM
–
IPDM E/R
Check results
Reproduced>>Install removed unit, and then check the other unit.
Not reproduced>>Replace removed unit.
IPDM E/R Ignition Relay Circuit Inspection
AKS00CJH
Check the following. If no malfunction is found, replace the IPDM E/R.
●
IPDM E/R power supply circuit. Refer to
PG-27, "IPDM E/R Power/Ground Circuit Inspection"
●
Ignition power supply circuit. Refer to
PG-10, "IGNITION POWER SUPPLY - IGNITION SW. IN “ON”
.
LAN-338
[CAN]
CAN SYSTEM (TYPE 9)
Revision: 2005 August
2005 Murano
CAN SYSTEM (TYPE 9)
PFP:23710
Component Parts and Harness Connector Location
AKS00AGU
PKIB6922E
CAN SYSTEM (TYPE 9)
LAN-339
[CAN]
C
D
E
F
G
H
I
J
L
M
A
B
LAN
Revision: 2005 August
2005 Murano
Schematic
AKS00AGV
TKWB0867E
LAN-340
[CAN]
CAN SYSTEM (TYPE 9)
Revision: 2005 August
2005 Murano
Wiring Diagram - CAN -
AKS00AGW
TKWB0868E
CAN SYSTEM (TYPE 9)
LAN-341
[CAN]
C
D
E
F
G
H
I
J
L
M
A
B
LAN
Revision: 2005 August
2005 Murano
TKWB0869E
LAN-342
[CAN]
CAN SYSTEM (TYPE 9)
Revision: 2005 August
2005 Murano
TKWB0870E
CAN SYSTEM (TYPE 9)
LAN-343
[CAN]
C
D
E
F
G
H
I
J
L
M
A
B
LAN
Revision: 2005 August
2005 Murano
TKWB0871E
LAN-344
[CAN]
CAN SYSTEM (TYPE 9)
Revision: 2005 August
2005 Murano
TKWB0872E
CAN SYSTEM (TYPE 9)
LAN-345
[CAN]
C
D
E
F
G
H
I
J
L
M
A
B
LAN
Revision: 2005 August
2005 Murano
Check Sheet
AKS00ASH
NOTE:
If a check mark is put on “NG” on “INITIAL DIAG (Initial diagnosis)”, replace the control unit.
PKIB4724E
LAN-346
[CAN]
CAN SYSTEM (TYPE 9)
Revision: 2005 August
2005 Murano
PKIB4725E
CAN SYSTEM (TYPE 9)
LAN-347
[CAN]
C
D
E
F
G
H
I
J
L
M
A
B
LAN
Revision: 2005 August
2005 Murano
PKIB4726E
LAN-348
[CAN]
CAN SYSTEM (TYPE 9)
Revision: 2005 August
2005 Murano
CHECK SHEET RESULTS (EXAMPLE)
NOTE:
If a check mark is put on “NG” on “INITIAL DIAG (Initial diagnosis)”, replace the control unit.
Case 1
Check harness between TCM and data link connector. Refer to
LAN-366, "Inspection Between TCM and Data
.
PKIB4866E
PKIB4657E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст