Nissan GT-R (2007-2014 year). HORN / INTERIOR LIGHTING SYSTEM / INTERIOR. Service Manual — part 3
INT-6
< SYMPTOM DIAGNOSIS >
SQUEAK AND RATTLE TROUBLE DIAGNOSES
Diagnostic Worksheet
INFOID:0000000009162321
PIIB8740E
Revision: 2012 November
2014 GT-R
SQUEAK AND RATTLE TROUBLE DIAGNOSES
INT-7
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
PIIB8742E
Revision: 2012 November
2014 GT-R
INT-8
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009162322
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precautions Necessary for Steering Wheel Rotation After Battery Disconnection
INFOID:0000000009162323
CAUTION:
Comply with the following cautions to prevent any error and malfunction.
• Before removing and installing any control units, first turn the ignition switch to the LOCK position,
then disconnect both battery cables.
• After finishing work, confirm that all control unit connectors are connected properly, then re-connect
both battery cables.
• Always use CONSULT to perform self-diagnosis as a part of each function inspection after finishing
work. If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
For vehicle with steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock and
cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the operation pro-
cedure below before starting the repair operation.
OPERATION PROCEDURE
1.
Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2.
Turn the ignition switch to ACC position.
(At this time, the steering lock will be released.)
3.
Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
Revision: 2012 November
2014 GT-R
PRECAUTIONS
INT-9
< PRECAUTION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
4.
Perform the necessary repair operation.
5.
When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the ignition switch from ACC position to ON position, then to LOCK position. (The steering wheel will lock
when the ignition switch is turned to LOCK position.)
6.
Perform self-diagnosis check of all control units using CONSULT.
Precaution for Procedure without Cowl Top Cover
INFOID:0000000009162324
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.
Precaution for Work
INFOID:0000000009162325
• After removing and installing the opening/closing parts, be sure to carry out fitting adjustments to check their
operation.
• Check the lubrication level, damage, and wear of each part. If necessary, grease or replace it.
PIIB3706J
Revision: 2012 November
2014 GT-R
INT-10
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000009162326
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
INFOID:0000000009162327
Tool number
(Kent-Moore No.)
Tool name
Description
(J-39570)
Chassis ear
Locates the noise
(J-43980)
NISSAN Squeak and Rattle
Kit
Repairs the cause of noise
SIIA0993E
SIIA0994E
Tool name
Description
Engine ear
Locates the noise
Remover tool
Removes clips, pawls and metal clips
Power tool
SIIA0995E
JMKIA3050ZZ
PIIB1407E
Revision: 2012 November
2014 GT-R
CLIP LIST
INT-11
< PREPARATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
CLIP LIST
Clip List
INFOID:0000000009162328
JMJIA3734GB
Revision: 2012 November
2014 GT-R
INT-12
< REMOVAL AND INSTALLATION >
DOOR FINISHER
REMOVAL AND INSTALLATION
DOOR FINISHER
Exploded View
INFOID:0000000009162329
Removal and Installation
INFOID:0000000009162330
CAUTION:
Wrap the tip of flat-bladed screwdriver with a shop cloth before remove.
REMOVAL
1.
Fully open the door window.
1.
Bracket
2.
Door finisher
3.
Power window switch finisher
4.
Armrest
5.
Step lamp
6.
Door grip cap
7.
Door corner cover inner
8.
Door panel
9.
Power window switch
: Clip
: Pawl
: Metal clip
JMJIA2155ZZ
Revision: 2012 November
2014 GT-R
DOOR FINISHER
INT-13
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
2.
Insert a remover tool (A) into the lower side of door grip cap (1),
then disengage and remove the pawls and metal clips.
3.
Insert a remover tool (A) between the door finisher and rear of
armrest (1), disengage the pawls and metal clips and then
remove the armrest.
4.
Remove the door finisher tightening bolts (A) shown in the fig-
ure.
5.
Remove the step lamp.
1.
Insert a remover tool (A) between the door finisher and the
step (1) to disengage the metal clips and remove the step
lamp.
2.
Remove the bolt located behind the step lamp.
6.
Remove the clip from the door finisher rear end. Refer to
: Pawl
: Metal clip
JMJIA2156ZZ
: Pawl
: Metal clip
JMJIA2157ZZ
NNJIA0175ZZ
: metal clip
JMJIA6123ZZ
Revision: 2012 November
2014 GT-R
INT-14
< REMOVAL AND INSTALLATION >
DOOR FINISHER
7.
Disengage the clips from the door finisher (1) rear side using a
remover tool (A).
CAUTION:
Insert the remover tool between door panel and clip, and
then disengage the clip.
8.
Remove the door finisher rear side lock knob cable (2) and the inside handle cable (1) from the inside
handle (A).
9.
Lift up the door finisher and pull it out toward the passenger
room. Disconnect the connectors (A) and (B) from the door fin-
isher rear side.
10. Remove the door finisher.
11. Remove the front door squawker (BOSE AUDIO WITH NAVIGA-
TION) after removing the door finisher. Refer to
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
When installing the door finisher, check that the clips are securely fitted in panel holes, and then press
them in.
: Clip
JMJIA2159ZZ
JMJIA2160ZZ
JMJIA2161ZZ
Revision: 2012 November
2014 GT-R
BODY SIDE TRIM
INT-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
BODY SIDE TRIM
Exploded View
INFOID:0000000009162331
Removal and Installation
INFOID:0000000009162332
CAUTION:
Wrap the tools with shop cloth or tape to prevent damage when using the tools during removal.
REMOVAL
FRONT PILLAR GARNISH
1.
Remove the front body side welt of the front pillar.
1.
Front pillar garnish
2.
Kicking plate outer
3.
Dash side finisher (RH)
4.
Kicking plate inner
5.
Rear side finisher
6.
Rear pillar finisher
7.
Body side welt
8.
Dash side finisher cover
9.
Dash side finisher (LH)
: Clip
: Pawl
: Metal clip
: Always replace after every disassembly
JMJIA2162ZZ
Revision: 2012 November
2014 GT-R
INT-16
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
2.
Insert the remover tool (A) into the clearance between the front pillar garnish (1) and the vehicle body, dis-
engage the metal clips, cut the clip (2) and then remove the front pillar garnish.
KICKING PLATE INNER
1.
Disengage pawls on rear end and side of kicking plate inner
using a remover tool (A).
2.
Disengage remaining pawls while rotating the kicking plate
inner.
3.
Pull kicking plate toward vehicle rear, disengage metal clips, and
then remove kicking plate inner.
DASH SIDE FINISHER
1.
Remove the kicking plate inner.
2.
Remove the clip (A) of the dash side finisher (1).
3.
Disengage and remove the clips of the dash side finisher using
the remover tool (B).
KICKING PLATE OUTER
1.
Remove the center mud guard. Refer to
EXT-34, "Removal and Installation"
: Clip
: Metal clip
NNJIA0016ZZ
: Pawl
JMJIA5244ZZ
: Pawl
: Metal clip
JMJIA5245ZZ
: Metal clip
JMJIA2165ZZ
Revision: 2012 November
2014 GT-R
BODY SIDE TRIM
INT-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
2.
Disengage and remove the pawls using a remover tool (A) after
removing the clip of kicking plate outer.
BODY SIDE WELT
1.
Remove the kicking plate inner.
2.
Remove the body side welt from the panel flange.
REAR SIDE FINISHER
1.
Remove the kicking plate inner.
2.
Remove the body side welt from the rear side finisher.
3.
Remove the rear seat cushion and the rear seatback. Refer to
SE-56, "Removal and Installation"
4.
Remove rear side finisher fixing clip (2).
5.
Disengage rear side finisher (1) fixing clips and pawls with a
remover tool (A), and then remove rear side finisher.
REAR PILLAR FINISHER
1.
Remove the rear seat cushion and the rear seatback. Refer to
SE-56, "Removal and Installation"
2.
Remove the kicking plate inner.
3.
Remove the rear side finisher and the body side welt of rear pillar finisher.
4.
Remove the rear side finisher.
5.
Remove the front seat belt shoulder anchor. Refer to
SB-6, "SEAT BELT RETRACTOR : Removal and
.
6.
Remove the mounting screw from rear pillar finisher (1) using a screwdriver (A).
7.
Disengage the clips and the metal clips from the rear pillar finisher using the remover tool (A).
INSTALLATION
: Pawl
NNJIA0018ZZ
: Clip
: Pawl
JMJIA5241ZZ
: Clip
: Pawl
: Metal clip
JMJIA5349ZZ
Revision: 2012 November
2014 GT-R
INT-18
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
Note the following, and install in the reverse order of removal.
CAUTION:
When installing body side trim, check that clips are securely fitted in panel holes on the body, and then
press them in.
Revision: 2012 November
2014 GT-R
REAR PARCEL SHELF FINISHER
INT-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
REAR PARCEL SHELF FINISHER
Exploded View
INFOID:0000000009162333
Removal and Installation
INFOID:0000000009162334
REMOVAL
1.
Remove the rear seat cushion and the rear seatback. Refer to
SE-56, "Removal and Installation"
2.
Remove the kicking plate inner (LH/RH) and body side welt (LH/RH). Refer to
.
3.
Remove the rear side finisher (LH/RH). Refer to
INT-15, "Removal and Installation"
4.
Remove the rear pillar finisher (LH/RH). Refer to
INT-15, "Removal and Installation"
5.
Remove the rear console assembly. Refer to
IP-23, "Removal and Installation"
1.
Child anchor cover
2.
Rear parcel shelf finisher
3.
Rear seat center finisher
: Clip
: Pawl
JMJIA2166ZZ
Revision: 2012 November
2014 GT-R
INT-20
< REMOVAL AND INSTALLATION >
REAR PARCEL SHELF FINISHER
6.
Remove the rear seat center finisher mounting bolts (B) using
socket wrench (A).
7.
Insert the remover tool (A) into the clearance between the rear
seat center finisher (1) and the vehicle body, and then disen-
gage the clips.
8.
Remove the rear parcel shelf finisher mounting clips (A).
9.
Remove the rear seat belt escutcheon.
10. Remove the rear seat belt inner anchor. Refer to
SB-11, "SEAT BELT RETRACTOR : Removal and Instal-
.
11. Disengage the child anchor cover (1) fixing pawls, with a
remover tool (A) and then remove the child anchor cover (LH/
RH).
NNJIA0106ZZ
: Clip
NNJIA0107ZZ
NNJIA0022ZZ
NNJIA0181ZZ
Revision: 2012 November
2014 GT-R
REAR PARCEL SHELF FINISHER
INT-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
12. Remove the rear seat belt (1) through the hole of rear parcel
shelf finisher (2) as shown in the figure.
13. Pull and remove the rear parcel shelf finisher after disengaging the clip from the back side of rear parcel
shelf finisher.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
Check that clips are securely fitted in panel holes on body when installing the rear parcel shelf finisher
and then press in.
NNJIA0109ZZ
Revision: 2012 November
2014 GT-R
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст