Dongfeng DFA1063DJ10 (14)-301/303. Manual — part 18
Rear Axle
RA-2
Disassembly of the brake
1.Cotter pin
2. Brake adjusting arm
3.Cotter pin
4.Plain washer
5.U-fork
6.Flat pin
7.Locking nut
8.Spring air chamber
9.Air chamber bracket
10.Cam ring cage ring
11.Bolt
12.Spring washer
13.Rubber plug
14.Dustproof shield
15.Brake bottom plate
16.Set screw
17.Steel lock wire
18.Supporting pin
19.Rivet
20.Brake bush
21.Brake shoe
22.Return spring
23.Return spring pin
24.Spring washer
25.Screw
26.Roller pin shaft
27.Roller
28.Clamp ring
29.Dustproof shield
30.Grease nipple
31.Bush
32.Oil seal
33.Cam shaft
34.Brake friction plate
Rear Axle
RA-3
Maintenance
Before using new axle, apply enough 2# lithium grease into every grease fitting.
First maintain
To assure the safe running of your vehicle and obtain a long service life, you have to do the first maintain
after the first 1,500~2,500kmafter leaving factory. Please note the following items:
1.Add or replace the gear oil for the reductor;
2.Dismantle and check the wheel hub brake drum assembly for any abnormal wear (please go to the Assembly
and Adjustment to see the reference)
3.Check the fastening piece.
Periodical maintain
Do the periodical maintain for the vehicle is a good way to prolong the service life and assure the safe run-
ning of the vehicle. If you follow the maintenance schedule to do the maintain, your vehicle may obtain the best
economic benefit.
The items of the periodical maintain are as following:
1.Add some grease to the grease nipple
2.Avoid important nut loosed
3.Adjust wheel hub bearing pretightening force and brake clearance
4.Add and replace the gear oil for the reductor
Periodical Maintain Schedule
Item
Maintenance Interval Mileage ( × 1000km)
First maintain
4
8
12 16 20 24 28 32 36 40 44 48 80
Clean the axle assy
● ● ● ● ● ● ● ● ● ● ● ●
Check main reductor for leakage
●
● ● ● ● ● ● ● ● ● ● ● ●
Replace grease of main reductor
●
●
●
●
Check lubricant level of the main
reductor and clean the vent plug
●
●
●
●
Check tightness of the important
bolts
●
● ● ● ● ● ● ● ●
Clean and adjust wheel hub bear-
ing
●
●
●
●
Do the magnetic particle test to
half axle sleeve
●
Check service brake and parking
brake efficiency
●
● ● ● ● ● ● ● ● ● ● ● ●
Check the tightness of the brake
bottom plate
●
●
●
●
Clean brake air chamber
●
Check brake pipeline for leakage
●
● ● ● ● ● ● ● ● ● ● ● ●
Rear Axle
RA-4
Assembly and Adjustment
Disassemble and asseble of the assembly
Rear wheel hub brake drum assembly
1.Fixed the rear axle and remove the half axle bolt by a spanner;
2.Pull out the half axle gently and when the spline passing the oil seal, turn the half axle slowly to avoid damage
the half axle oil seal;
3.Take down three screws of the stop spacer by a screwdriver, then remove the stop spacer and dismantle the
adjusting nut by a spanner;
4.Turn the wheel hub brake drum a little and pull it, gently knock at the brake drum at the same time to loose the
inner ring of the outer bearing, then take down the wheel hub brake drum, but you need to pay attention that the
assembly is so heavy that may be fallen down or hurt someone, and the inner ring of the outer bearing need to
care at the same time, don't fall it.
The assembling sequence of the rear wheel hub brake drum assembly is opposite to the above sequence, and
you must to pay attention to the tightening torque of the thread connecting parts and the adjustment of the bearing
pretightening force.
Assembly of the main reductor assembly
1) Assembly of the drive gear
1.Press the outer ring of the front inner and outer bearing into the bearing seat;
2.Press the oil seal on the oil seal seat;
3.Press the inner ring of the front inner bearing onto the drive gear, and install the spacer sleeve, adjusting spacer,
bearing seat assembly and front outer bearing inner ring in sequence at the spline end of the gear;
4.Measure the pretightening load of the drive gear bearing: install the oil seal assembly, thrust washer, flange fork
and washer, then tighten the castle nut with a torque 350~500N.m and measure the pretightening force at this
time, the starting force of pulling the flange hole of the bearing seat should be 12~30N;
5.If the pretightening force is disqualified, you need to replace the adjusting spacer, reassemble to qualified;
6.Make use of a cotter pin to lock the castle nut.
2) Assembly of the differential
1.Install the bearing to the left and right differential housing;
2.Install planet gear, half axle gear, cross shaft, planet gear supporting washer, and half axle gear supporting
washer;
3.Measure the tooth space of the planet gear of the differential, check the clearance between half axle gear sup-
porting end face and the supporting washer with a clearance gauge, it should be ≤ 0.8 mm;
4.Align the marks of left and right differential housing and then assemble.
Tightening torque: 140~160N.m
3) Assembly of the main reductor assembly
1.After assembled the bearing outer ring of the differential, install it onto the main reductor housing;
2.Install the adjusting nut and the bearing cover, then fasten with bolts;
3.Equably tighten the adjusting nut to pretighten the load until the pretightening load is between 16.4~24.3N;
4.Install the adjusting spacer of main cone to the bearing seat and assemble the drive conical gear assembly;
5.Adjust the gear tooth space to 0.20~0.40mm:
The change value of the tooth space ≤ 0.15 mm
Rear Axle
RA-5
6.Paint two or three engaged teeth of driven gear red to chaeck the contact zone, if the contact area is improper,
increase or reduce the thickness of the adjusting spacer until it is proper;
Sketch map of the contact zone is as follows:
7.Tighten the bearing cover fixed bolt, reassemble the stop spacer.
Adjustment of the axle
Adjustment of the brake clearance
No matter if the brake clearance is too big or too small, it will effect the brake efficiency of the vehicle.
Please adjust the worm shaft hex-head of the adjusting arm by a spanner. Firstly, turn it with the clockwise until
you can't turn to make the clearance become zero, then turn with the counter clockwise until you hear two sounds
of steel ball, and the middle part clearance of the brake friction plate is 0.4~0.7mm.
Gear contact zone
Adjusting method
1
Proper contact zone
No need to adjust
2
The drive gear & the
driven gear is too far
The drive gear and the driven
gear is too far (reduce the
thickness of the spacer)
3
The drive gear & the
driven gear is too near
The drive gear and the driven
gear is too near (increase the
thickness of the spacer)
4
The contacting area of the
driven taped gear is too
low
The drive gear and the driven
gear is too near (increase the
thickness of the spacer)
5
The contacting area of the
driven tapered gear is too
high
The drive gear and the driven
gear is too far (reduce the
thickness of the spacer)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст