Fiat 500L (2022 year). Manual in english — page 14
MULTIMEDIA
220
TIPS, CONTROLS
AND GENERAL INFO
ROAD SAFETY
171) 172)
Learn how to use the various system
functions before setting off.
Read the instructions for the system
carefully before starting to drive.
RECEPTION CONDITIONS
Reception conditions change
constantly while driving. Reception may
be interfered with by the presence
of mountains, buildings or bridges,
especially when you are far away from
the broadcaster.
WARNING The volume may be
increased when receiving traffic
information and news.
NOTE The DAB frequency can be used
in countries where digital transmission
technology is available. The device
will tuned to any frequency if the DAB
button is pressed in a country where
the service is not provided.
CARE AND MAINTENANCE
76) 77)
Observe the following precautions to
ensure the system is fully operational:
the display lens should not come into
contact with pointed or rigid objects
which could damage its surface; use a
soft, dry anti-static cloth to clean and
do not press.
do not use alcohol, petrol and
derived products them to clean the
display lens and make sure that the
UconnectTM
system is switched off
during cleaning.
prevent any liquid from entering the
system: this could damage it beyond
repair.
MULTIMEDIA DEVICES
WARNING Some multimedia players
may not be compatible with the
Uconnect™
system.
Only use devices (e.g. USB flash drives)
from safe sources on the car.
NOTE The system supports FAT32 and
exFAT formatted USB devices only.
The system does not support devices
with a capacity higher than 64 GB.
Devices from unknown sources could
contain software infected by viruses
which, if installed on the car, could
increase the vulnerability of the car's
electric/electronic systems to hacking.
ANTI-THEFT
PROTECTION
The system is equipped with an
anti-theft protection system based on
the exchange of information with the
electronic control unit (Body Computer)
on the vehicle.
This guarantees maximum safety and
prevents the secret code from being
entered after the power supply has
been disconnected.
If the check has a positive outcome,
the system will start to operate,
whereas if the comparison codes are
not the same or if the electronic control
unit (Body Computer) is replaced,
the system will ask the user to enter
the secret code according to the
procedure described in the paragraph
below.
Entering the secret code
When the system is switched on, if the
code is requested, the display will show
"Please enter Anti-Theft Code" followed
by the screen showing a keypad
to enter the secret code. The secret
code has four numbers from 0 to 9:
to insert the code numbers, rotate the
BROWSE/ENTER dial and press to
confirm.
After entering the fourth digit, the
system begins operating. If an incorrect
code is entered, the system displays
"Incorrect Code" to notify the user of
the need to enter the correct code.
After the 3 available attempts to
enter the code, the system displays
"Incorrect Code. Radio locked. Please
wait for 30 minutes". After the text has
-------------------------------------------------------------------------------------------------------------------------------------------------------------
221
disappeared it is possible to start the
code entering procedure again.
Car radio passport
This document certifies ownership of
the system. The car radio passport
shows the system model, serial
number and secret code.
In case of loss of the car radio
passport, contact the Fiat Dealership,
taking an ID document and the car
ownership documents.
WARNING Keep the car radio passport
in a safe place so that you can give the
information to the relevant authorities if
the system is stolen.
WARNINGS
In the event of a fault, the system must
only be checked and repaired by a Fiat
Dealership.
If the temperature is particularly low,
the display may take a while to reach
optimum brightness.
If the car is stopped for a while and
the external temperature is very high,
the system may go into "thermal
protection" mode, suspending
operation until the radio temperature
returns to acceptable levels.
Look at the screen only and when it
is necessary and safe. If you need to
look at the screen for a long time, pull
over to a safe place so as not to be
distracted while driving.
Immediately stop using the system
in the event of a fault. Otherwise the
system might be damaged. Contact a
Fiat Dealership as soon as possible to
have the system repaired.
171)
Follow the safety rules here below:
otherwise serious injuries may occur to
the occupants or the system may be
damaged.
172)
If the volume is too loud this can
be dangerous. Adjust the volume so that
you can still hear background noises (e.g.
horns, ambulances, police vehicles, etc.).
76)
Only clean the front panel and the
display with a soft, clean, dry, anti-static
cloth. Cleaning and polishing products
may damage the surface. Do not use
alcohol or similar products to clean the
control panel or the display.
77)
Do not use the display as a base for
supports with suction pads or adhesives
for external navigators or smartphones or
similar devices.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
MULTIMEDIA
222
Uconnect™ 5” LIVE
CONTROLS ON FRONT PANEL
227
F0Y0633C
-------------------------------------------------------------------------------------------------------------------------------------------------------------
223
FRONT CONTROL PANEL SUMMARY TABLE
Button
Functions
Mode
On/off
Brief button press
Volume adjustment
Left/right rotation of knob
Volume activation/deactivation (Mute/Pause)
Brief button press
Display on/off
Brief button press
Accessing the Vehicle Settings menu
Brief button press
Exit the selection/return to previous screen
Brief button press
BROWSE ENTER
Scrolling the list or tuning to a radio station
Left/right rotation of knob
Confirmation of the option displayed
Brief button press
APPS
Access to additional features (e.g. Time display,
Outside Temperature, Media, Radio data function and
Uconnect™
LIVE services, where provided)
Brief button press
PHONE
Phone data display
Brief button press
TRIP
Access to the TRIP menu
Brief button press
MEDIA
Source selection: USB or
Bluetooth®
Brief button press
RADIO
Access to the Radio mode
Brief button press
-------------------------------------------------------------------------------------------------------------------------------------------------------------
MULTIMEDIA
224
STEERING WHEEL CONTROLS
The controls for the main system functions are present on the steering wheel to make control easier.
The activation of the function selected is controlled, in some cases, by how long the button is pressed (short or long press) as
described in the table below.
228
F0Y0632C
-------------------------------------------------------------------------------------------------------------------------------------------------------------
225
STEERING WHEEL CONTROLS SUMMARY TABLE
Button
Interaction
Acceptance of incoming call
Answering the second incoming call and putting the active call on hold
Display on the instrument panel of the list of the last 10 calls (only with call browsing active)
Activation of voice recognition
Interruption of the voice message in order to give a new voice command
Interruption of voice recognition
Rejection of incoming call
Ending of call in progress
Exit the display of the last calls on the instrument panel display (only with call browsing active) (for
versions/markets, where provided)
Short press (Phone mode): selection, on the instrument panel display, of the last calls/text messages (only with
call browsing active)
-------------------------------------------------------------------------------------------------------------------------------------------------------------
MULTIMEDIA
226
CONTROLS BEHIND THE STEERING WHEEL
Buttons
Interaction
Button A (steering wheel left side)
Upper button
Brief button press: search for next radio station or selection of USB next track.
Long button press: scan of higher frequencies until released/fast forward of USB track.
Central button
With each press it scrolls through sources AM, FM, DAB (where provided), USB. Only the available
sources will be selected.
Lower button
Brief button press: search for next radio station or select USB previous track.
Long button press: scan of lower frequencies until released/fast forward of USB track.
Button B (steering wheel right side)
Upper button
Increasing volume
Brief button press: single volume increase.
Long button press: fast volume increase.
Central button
Activation/deactivation of Mute / Pause function
Lower button
Decreasing volume
Brief button press: single volume decrease.
Long button press: fast volume decrease.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
227
SYSTEM ON / OFF
The system is switched on/off by
pressing the
(ON/OFF) button/knob.
Turn the button/knob clockwise
to increase the radio volume or
anticlockwise to decrease it.
USB SOURCE
Depending on the version, the car may
have one or two USB ports on the
central tunnel fig. 229.
To activate the USB mode, insert the
corresponding device into one of the
USB ports.
WARNING After using a USB charging
port, we recommend disconnecting the
device (smartphone), always removing
the cable from the vehicle socket first,
never from the device. Cables left
flying or connected incorrectly could
compromise correct recharging and/or
the USB socket condition.
The
Uconnect™
system may not
support some USB keys: in this case,
it may not automatically switch from
"Radio” mode to "Media” mode.
If the device used does not play,
verify its compatibility by selecting
Media mode: a dedicated message will
appear on the
Uconnect™
system
display.
NOTE The USB ports handle
data transmission from the Pen
Drive/Smartphone, etc. and slow
recharging of an external device, which
is not guaranteed as it depends on the
device type/brand.
229
F0Y0728
RADIO MODE
After the desired radio station is
selected, the following information is
shown on the display:
At the top
: the list of radio stations
stored (preset) is displayed; the station
currently playing is highlighted.
In the middle
: display of the name
of the current radio station and the
buttons
/
for selecting the
previous or next radio station.
At the bottom
: display of the following
buttons:
"Browse": list of the radio stations
available;
"AM/FM", "AM/DAB", "FM/DAB":
selection of the desired frequency
band (graphic button reconfigurable
according to the band selected: AM,
FM or DAB (where provided));
“Tune": manual radio station tuning
(not available for DAB radio);
"Info": additional information on the
source being listened to;
"Audio": access to the "Audio
Settings" screen.
Audio menu
The following adjustments can be
carried out using the "Audio" menu:
"Equalizer" (for versions/markets,
where provided);
"Balance/Fade" (left/right and
front/rear audio balance adjustment);
"Volume / Speed" (excluding versions
with Hi-Fi system) speed-dependent
automatic volume adjustment;
"Loudness" (for versions/markets,
where provided);
"Auto-On Radio" (for
markets/versions, where provided)
"Radio Off Delay".
MEDIA MODE
With Media mode active, briefly press
the
/
graphic buttons to play
the previous/next track or keep the
/
buttons pressed to fast
rewind/forward the track.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
MULTIMEDIA
228
Track selection (Browse)
NOTE The keyboard is not available
for languages not supported by
the system which feature special
characters (e.g. Greek). In these cases
this function will be limited.
Bluetooth® SOURCE
Pairing a Bluetooth® audio device
To pair a
Bluetooth®
audio device,
proceed as follows:
activate the
Bluetooth®
function on
the device;
press the MEDIA button on the front
panel;
if the "Media" source is active, press
the "Source" graphic button;
select the
Bluetooth®
Media
source;
press the "Add Device" button;
search for
Uconnect™
on the
Bluetooth®
audio device (during the
pairing stage a screen is displayed
showing the progress of the operation);
when requested by the audio device,
enter the PIN code shown on the
system display or confirm on the device
the PIN displayed;
if the pairing procedure is completed
successfully, a screen is displayed.
Answer “Yes” to the question to pair
the
Bluetooth®
audio device as
favourite (the device will have priority
over all other devices to be paired
subsequently). If “No” is selected, the
priority is determined according to the
order of connection. The last device
connected will have the highest priority;
an audio device can also be paired
by pressing the PHONE button on the
front panel and by selecting “Settings”
or, from the “Settings” menu, selecting
“Phone/Bluetooth”.
NOTE When modifying the name-
device in the
Bluetooth®
settings of
the phone (where provided), the Radio
may change the track being played
if the device is connected via USB
after the
Bluetooth®
connection.
After updating the phone software, for
proper operation, it is recommended
to remove the phone from the list of
devices linked to the radio, delete the
previous system pairing also from the
list of
Bluetooth®
devices on the
phone and make a new pairing.
WARNING If the
Bluetooth®
connection between mobile phone
and system is lost, consult the mobile
phone handbook.
PHONE MODE
Phone mode activation:
Press the PHONE button on the front
panel to activate the Phone mode. Use
the graphic buttons on the display to:
dial the phone number (using the
graphic dial pad on the display);
display and call the contacts in the
phonebook of the mobile phone;
display and call contacts from the
registers of previous calls;
pair up to 10 phones/audio device
to make access and connection easier
and quicker;
transfer calls from the system to
the mobile phone and vice versa and
deactivate the microphone audio for
private conversations. The mobile
phone audio is transmitted through
the car’s sound system; the system
automatically mutes the
Uconnect™
system audio when the Phone function
is used.
NOTE To consult the list of mobile
phones and supported functions, visit
the www.driveuconnect.eu website
Pairing a mobile phone
Proceed as follows:
activate the
Bluetooth®
function on
the mobile phone;
press the PHONE button on the front
panel;
if no phone is paired with the system
yet, the display shows a dedicated
screen;
select "Yes" to start the pairing
procedure, then search for the
Uconnect™
device on the mobile
-------------------------------------------------------------------------------------------------------------------------------------------------------------
229
phone (if "No" is selected, the Phone
main screen is displayed);
when prompted by the mobile
phone, use its keypad to enter the PIN
code shown on the system display or
confirm on the mobile phone the PIN
displayed;
from the "Phone" screen you can
always pair a mobile phone by pressing
the "Settings" graphic button: press the
"Add Device" button and proceed as
described above.
During the pairing stage a screen is
displayed showing the progress of the
operation.
When the pairing procedure is
completed successfully, a screen
is displayed: answer “Yes” to the
question to pair the mobile phone as
favourite (the mobile phone will have
priority over all other mobile phones
to be paired subsequently). If no other
devices are paired, the system will
consider the first paired device as the
favourite.
NOTE To ensure proper operation
after updating the phone software, it is
recommended to remove the phone
from the list of devices linked to the
radio, delete the previous system
pairing also from the list of
Bluetooth®
devices on the phone and make a new
pairing.
Making a phone call
A call can be made by:
selecting the
icon (mobile phone
phonebook);
selecting "Recent Calls";
selecting the icon
pressing the "Redial" graphic button.
NOTE The operations described above
are accessible only if supported by the
mobile phone in use.
Text Message Reader
The system can read the messages
received by the mobile phone. To use
this function, the mobile phone must
support the text exchange function
through
Bluetooth®
.
If this function is not supported by the
phone, the corresponding graphic
button
is deactivated (greyed out).
When a text message is received, the
display will show a screen where the
options "Listen", "Call" or "Ignore" can
be selected.
Press the
graphic button to access
the list of text messages received by
the mobile phone (the list displays a
maximum of 60 messages received).
NOTE On some mobile phones,
to make the text message voice
reading function available, the text
message notification option on the
phone must be enabled; this option is
usually available on the phone, in the
Bluetooth®
connections menu for a
device registered as
Uconnect™
.
After enabling this function on the
mobile phone, it must be disconnected
and reconnected with the
Uconnect™
system in order to make it effective.
WARNING Some mobile phones may
not take the text message delivery
confirmation settings into account
when interfacing with
Uconnect™
.
If a text message is sent via the
Uconnect™
system, the driver could
face an additional cost, without any
warning, due to the text message
delivery confirmation request sent by
the phone. For any problems related
to the above, contact your telephone
service provider.
Text message options
Predefined messages are stored in the
system memory and can be sent to
answer a received message or as a
new message.
Yes
No
Okay
I can't talk right now
Call me
I'll call you later
-------------------------------------------------------------------------------------------------------------------------------------------------------------
MULTIMEDIA
230
I’m on my way
Thanks
I'll be late
Stuck in traffic
Start without me
Where are you?
Are you there yet?
I need directions
I'm lost
See you later
I will be 5 (or 10, 15, 20, 25, 30, 45,
60) (*) minutes late
See you in 5 (or 10, 15, 20, 25, 30,
45, 60) (*) minutes
(*) Only use the numbers listed,
otherwise the system will not take the
message.
When receiving a text message, the
systems also allows the same message
to be forwarded.
NOTE For details on how to send an
text using the voice commands, refer to
the dedicated paragraph.
Browsing text messages
(for versions/markets, where provided)
Using the steering wheel controls, you
can view and manage the last 10 text
messages received on the instrument
panel display. To use this function,
the mobile phone must support
the text exchange function through
Bluetooth®
.
Select “Phone” on the instrument panel
Setup menu and then select “Text
message reader” using the
/
steering wheel controls. The "SMS
reader" submenu allows the last 10
SMS messages to be displayed.
Uconnect™ LIVE
SERVICES
(where provided)
Press the APPS button to access
the menu where all the application
functions of the system are present,
such as: time display,
eco:Drive™
function data, Trip Computer, Outdoor
temperature, Settings,
Uconnect™
LIVE
applications.
If there is a
Uconnect™ LIVE
icon,
the system is set up for the connected
services and allows the applications to
be used directly from the radio menu,
for a more efficient and advanced use
of the car.
The application functions are present
according to the car configuration and
to the market.
To use the
Uconnect™ LIVE
services,
you need to:
to download
Uconnect™ LIVE
App
from "App Store" or "Google
play" on your compatible smartphone,
making sure that the data connection is
enabled;
register, through the
Uconnect™ LIVE App
on the
www.driveuconnect.eu or www.fiat.it
website
start the
Uconnect™ LIVE App
on the smartphone and enter your
credentials.
For more information relating to the
services available on the market,
consult the www.driveucoinnect.eu
site.
First access to the car
After starting the
Uconnect™ LIVE
App
and entering your credentials,
to access the
Uconnect™
LIVE App
services in the car
you need
Bluetooth®
pairing
between your smart phone and the
Uconnect™
system as described
in the "Registering your mobile
phone" section. The list of supported
mobile phones is available on
www.driveuconnect.eu
After pairing, press the
Uconnect™
LIVE
graphic button on the display to
access the connected services.
When the activation process is
completed, the display shows a
dedicated message. In the case
of services that require a personal
profile, you can connect your own
account through the
Uconnect™ LIVE
-------------------------------------------------------------------------------------------------------------------------------------------------------------
231
App
or in the reserved area on the
www.driveuconnect.eu site.
User not connected
If the device is not paired to a
Bluetooth®
telephone, if the
Uconnect™ LIVE
graphic button is
pressed, the system menu has its icons
disabled, except for
eco:Drive™
.
For further details on the
eco:Drive™
function refer to the dedicated
paragraph.
Uconnect™ LIVE services setup
using the dedicated menu
On the
Uconnect™
system menu
dedicated to
Uconnect™ LIVE
services the “Settings” section can be
accessed by pressing the icon
. In
this section you can check the system
options and change them according to
your preferences.
System updating
In case a system update is available
for the
Uconnect™
system during use
of the
Uconnect™ LIVE
services, a
message to this effect will appear on
the screen.
The update includes a download of the
new software version for managing the
Uconnect™ LIVE
services.
Updating is effected when using the
traffic data from the coupled smart
phone: the amount of traffic generated
will be communicated to the driver.
WARNING In order not to compromise
the proper functioning of the
Uconnect™
during installation, do not
carry out any other operations but wait
until it is finished.
Uconnect™ LIVE app
The
Uconnect™ LIVE App
must be
installed on your smartphone to access
the connected services on the car. This
can be used to manage your profile
and customise your
Uconnect™
LIVE
experience. The App can by
downloaded from "App Store" or
"Google play".
For safety reasons, the App cannot be
accessed when the phone is paired
with the
Uconnect™
system.
Personal details (e-mail and
password) are required to access the
Uconnect™ LIVE
services using the
Uconnect™
system menu, therefore
the content of your personal accounts
is protected and can only be accessed
by the real user.
Connected services that can be
accessed on the car
The
Uconnect™ LIVE
services
available in the
Uconnect™
system
menu can change according to the
market.
The
eco:Drive™
application was
developed to improve the driving
experience and therefore it can
be used in all markets where the
Uconnect™ LIVE
services are
accessible. For further information visit
the www.driveuconnect.eu website.
eco:Drive™
The
eco:Drive™
application allows
you to display your driving behaviour in
real time, in order to help you reach
a more efficient driving style as far
as consumption and emissions are
concerned.
It is also possible to consult the data on
the
Uconnect™ LIVE App
.
Driving style is evaluated by means of
four indices which monitor the following
parameters:
Acceleration
Deceleration
Shifting
Speed
eco:Drive™ display
Press the
eco:Drive™
graphic button
to interact with the function. A screen
will be displayed showing the 4 indices
described above. These indices are
grey until the system has enough data
to evaluate the driving style. Once
sufficient data are available, the indices
will have 5 colours depending on the
evaluation: dark green (very good), light
-------------------------------------------------------------------------------------------------------------------------------------------------------------
MULTIMEDIA
232
green, yellow, orange and red (very
bad).
"
Current trip index" refers to the entire
value calculated in real time based on
the average of the described indices.
It represents eco-friendliness of the
driving style: from 0 (low) to 100 (high).
In the event of extended inactivity, the
display will show the average of the
indices up to that moment ("
Average
Index") then the indices will be coloured
again in real time as soon as the car is
restarted.
To check the data average of previous
route (the "route" starts when the
ignition key is turned to MAR and stops
when it is turned to STOP), select the
"
Previous route" graphic button.
The details of the previous trip can also
be displayed by pressing the "
Details"
graphic button to show trip duration
(time and mileage) and average speed.
WARNING Do not unpair the
smartphone from the
Uconnect™
LIVE App
before the system has
downloaded the data, otherwise it
could be lost. During the transfer of
data to the devices, messages may
appear on the
Uconnect™
display to
guide the user correctly through the
operation; follow these instructions.
These messages are only displayed
with the ignition key at STOP and when
a delay in the
Uconnect™
system
switching off is set. The data are
automatically transferred to the devices
when the engine is switched off.
Transferred data will be deleted from
the system memory in this manner.
You can choose to store the trip data
or not, by pressing the "
Settings"
graphic button and setting storage
activation as desired.
my:Car
my:Car allows you to keep the
"condition" of your car always under
control. my:Car application can detect
faults in real time and inform the driver
on impending scheduled service
deadlines.
To interact with the application, press
"my:Car" graphic button: a screen will
appear on the display showing the
"care:Index" section which contains
detailed information on car status.
Press the "Active warnings" graphic
button to show the details of any faults
on the car which caused a warning
light to switch on.
The car status can be seen both on
www.driveuconnect.eu or through the
Uconnect™ LIVE App
.
"SETTINGS" MENU
"Settings" Menu Display
To access the "Settings" menu press
the
button on the front panel.
As a guideline, the menu includes the
following items:
Language
Display
Units (for versions/markets, where
provided)
Voice Commands
Clock and Date
Safety & Driving Assistance (for
versions/markets, where provided)
Lights
Doors & Locks
Key off options
Audio
Phone / Bluetooth
Radio Setup
SiriusXM Setup (for versions/markets,
where provided)
Restore Default Settings
Clear Personal Data
VOICE COMMANDS
NOTE Voice commands are not
available for languages not supported
by the system.
NOTE Voice entry of addresses is
only supported in the country in which
you are located and provided that
the system language matches the
local language. For example, if the car
is located in Italy, it will be possible
to enter Italian addresses only if the
system language is set to "Italian".
To use the voice commands, press
the
button ("Voice" button) on the
-------------------------------------------------------------------------------------------------------------------------------------------------------------
233
steering wheel controls and say the
function you want to activate aloud.
Phone functions
The
button activates the following
functions:
Call
Dial
Redial
Call back
Show recent calls
Show outgoing calls
Show missed calls
Show incoming calls
Phonebook
Search
Show text message
Radio functions
The
button activates the following
functions:
Tune to XXX FM
Tune to XXX AM
Tune in Radio XXX
Turn to the DAB channel (where
provided)
Media Functions
The
button activates the following
functions:
Play song...
Play album…
Play artist…
Play genre…
Play playlist…
Play podcast…
Play audiobook…
Play track number...
Select the source
View
-------------------------------------------------------------------------------------------------------------------------------------------------------------
MULTIMEDIA
234
Uconnect™ 7” HD LIVE / Uconnect™ 7” HD Nav LIVE
CONTROLS ON FRONT PANEL
230
F0Y0739
-------------------------------------------------------------------------------------------------------------------------------------------------------------
235
FRONT CONTROL PANEL SUMMARY TABLE
Button
Functions
Mode
On/off
Short button press
Volume adjustment
Left/right rotation of knob
Volume activation/deactivation (Mute/Pause)
Short button press
Display on/off
Short button press
Exit the selection/return to previous screen
Short button press
Scrolling the list or tuning to a radio station
Display list of stations (Radio mode)
Scroll contents of sources (Media mode)
Media source track change
Station change (RADIO mode)
Left/right rotation of knob
Confirmation of the option displayed Browsing lists
opening (Radio mode and Media mode)
Short button press
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст