Fiat Ulysse (2022 year). Manual in english — page 2
20
Dashboard instruments
indicating the driving range in miles or
kilometres.
While driving, the message is displayed every 30
seconds. The alert is repeated when switching
on the ignition.
You can continue driving for up to 685 miles
(1,100 km) before the
engine starting
prevention
system is triggered.
Have it checked by a Fiat Dealership or a
qualified workshop.
Starting prevented
Every time the ignition is switched on, the
message "
Emissions control fault: Starting
prevented
" or "
NO START IN
" is displayed.
To restart the engine
Contact a Fiat Dealership or a qualified
workshop.
Power
indicator (Electric)
CHARGE
Traction battery charging during deceleration
and braking.
ECO
Moderate energy consumption and optimised
driving range.
POWER
Energy consumption by the drive train during
acceleration.
NEUTRAL
When the ignition is switched on, the vehicle’s
electric drive train neither consumes nor
generates energy; after sweeping over the
indicator, the needle returns to its "neutral"
position: between ECO and CHARGE.
With the ignition off, opening the driver's
door activates the indicator, which moves
to the "neutral" position: between ECO and
CHARGE.
Charge level indicator
(Electric)
The traction battery's actual charge level and
the remaining range are displayed continuously
when the vehicle is started.
With the ignition off, opening the driver's
door activates the indicator.
Associated warning lamps
Two successive alert levels indicate that the
energy available has dropped to a low level:
1st level: Reserve
0 %
100
The state of charge of the traction battery
is low.
14/02/2022 15:33:02
-------------------------------------------------------------------------------------------------------------------------------------------------------------
21
Dashboard instruments
1
Fixed LED and needle in the red zone,
accompanied by an audible signal.
► View the remaining range on the instrument
panel.
► Put the vehicle on charge as soon as
possible.
2nd level: Critical
The state of charge of the traction battery
is critical.
Fixed, together with the reserve LED,
accompanied by an audible signal.
► You must put the vehicle on charge.
The remaining range is no longer
calculated. The drive train power
gradually decreases.
The heating and air conditioning are switched
off (even if the needle indicating their
consumption is not at the "
ECO
" position).
Thermal comfort
consumption indicator
(Electric)
The gauge shows the consumption of the
traction battery's electrical energy by the thermal
comfort devices in the passenger compartment.
The devices in question are the heating and air
conditioning systems.
This equipment can be used:
– If the vehicle is not plugged in, when the
READY
lamp is lit.
– If the vehicle is plugged in, when the ignition is
switched on ("Lounge" mode).
Selecting
ECO
mode limits the performance
of some of this equipment. The needle on the
thermal comfort consumption indicator then
moves into the "
ECO
" zone.
To quickly heat or cool the passenger
compartment, feel free to temporarily
select the maximum heating or cooling
setting.
When the heating is on maximum, the gauge
on the thermal comfort consumption indicator
is in the
MAX
zone. When the air conditioning
is on maximum, it stays in the
ECO
zone.
Excessive use of thermal comfort equipment,
particularly at low speed, can significantly
decrease the vehicle's range.
Remember to optimise equipment settings
upon achieving the desired level of comfort,
and adjust them if necessary whenever you
start the vehicle.
After an extended period without using the
heating, you may notice a slight odour during
the first few minutes of use.
Distance recorders
The total and trip distances are displayed for
thirty seconds when the ignition is switched off,
when the driver's door is opened and when the
vehicle is locked or unlocked.
14/02/2022 15:33:02
-------------------------------------------------------------------------------------------------------------------------------------------------------------
22
Dashboard instruments
Total distance recorder
This measures the total distance travelled by the
vehicle since its initial registration.
Trip distance recorder (Diesel)
This measures the distance travelled since it was
last reset by the driver.
Resetting the trip recorder
► With the ignition on, press the button until
zeros appear.
Lighting dimmer
This system allows the brightness of the
instruments and controls to be adjusted manually
to suit the ambient light level.
With buttons
With the lamps on, press button
A
to increase
the brightness of the lighting, or button
B
to
decrease it.
Release the button when the desired brightness
is reached.
With touch screen
► In the
Settings
menu, select "
Brightness
"
or "
OPTIONS
", "
Screen configuration
" then
"
Brightness
".
► Adjust the brightness by pressing the arrows
or moving the slider.
The brightness can be set differently for
day mode and night mode.
Trip computer
Displays information related to the current trip
(range, fuel consumption, average speed, etc.).
Information
display
To display the various trip computer tabs in turn:
14/02/2022 15:33:03
-------------------------------------------------------------------------------------------------------------------------------------------------------------
23
Dashboard instruments
1
► Press the button located on the end of the
wiper control stalk
.
With steering-mounted controls
► Press the knob on the
steering wheel
.
On the instrument panel
► Press this button.
The following current information is shown in
turn:
– Driving range (Diesel).
– Current consumption.
– Stop & Start time counter (Diesel).
– Trip "
1
" followed by (depending on version)
trip "
2
" including average speed, average
consumption and distance travelled for each trip.
Trips "
1
" and "
2
" are independent but their use
is identical.
For example, trip "
1
" can be used for daily
figures and trip "
2
" for monthly figures.
Trip reset
The reset is performed when the trip counter is
displayed.
► Press the button on the end of the
wiper
control stalk
for more than two seconds.
► Press the knob on the
steering wheel
for
more than two seconds.
► Press this button for more than 2 seconds.
Definitions
Range
(miles or km)
(Traction battery charge level percentage)
(Electric)
Distance that can still be travelled with the
fuel remaining in the tank (based on the
average fuel consumption over the last few miles
(kilometres) travelled).
This value may vary following a change in driving
style or terrain, leading to a significant change in
current fuel consumption.
When the range falls below 19 miles (30 km),
dashes are displayed.
After filling with at least 5 litres of fuel, the range
is recalculated and is displayed if it exceeds 62
miles (100 km).
Dashes appearing permanently in place of
numbers while driving indicates a malfunction.
14/02/2022 15:33:03
-------------------------------------------------------------------------------------------------------------------------------------------------------------
24
Dashboard instruments
Contact a Fiat Dealership or a qualified
workshop.
Current consumption
(mpg or l/100 km or km/l)
(miles/kWh or kWh/100 km or km/kWh) (Electric)
/
Calculated during the last few
seconds.
This function is only displayed at speeds above
19 mph (30 km/h) (Diesel).
Average consumption
(mpg or l/100 km or km/l)
(miles/kWh or kWh/100 km or km/kWh) (Electric)
/
Calculated since the last trip
computer reset.
Average speed
(mph or km/h)
Calculated since the last trip computer
reset.
Distance travelled
(miles or km)
Calculated since the last trip computer
reset.
Stop & Start time counter
(minutes/seconds or hours/minutes)
If your vehicle is fitted with the Stop & Start
function, a time counter calculates the time spent
in STOP mode during a journey.
The time counter is reset each time the ignition is
switched on.
Touch screen
This system gives access to the following
elements:
– Permanent display of the time and outside
temperature (a blue warning lamp appears if
there is a risk of ice).
– Vehicle functions and equipment setting
menus.
– Audio system and telephone controls and
display of related information.
– Display of visual manoeuvring aid functions
– Internet services and display of related
information.
– Navigation system controls and
display of related information (depending on
version).
For safety reasons, always stop the
vehicle before performing operations
that require sustained attention.
Some functions are not accessible while
driving.
Recommendations
This screen uses capacitive sensing technology.
– Do not use pointed objects on the touch
screen.
– Do not touch the touch screen with wet hands.
– Use a soft, clean cloth to clean the touch
screen.
Principles
► Use the buttons on each side of the touch
screen to access the menus, then press the
buttons that appear on the touch screen.
Some menus may display across two pages:
press the "
OPTIONS
" button to access the
second page.
After a few moments with no action on
the second page, the first page is
displayed automatically.
To deactivate/activate a function, select "
OFF
"
or "
ON
".
Configuring a function
Access to additional information on the
function
Confirm
Return to the previous page or confirm
Menus
14/02/2022 15:33:04
-------------------------------------------------------------------------------------------------------------------------------------------------------------
25
Dashboard instruments
1
Press the touch screen with three fingers
to show all of the menu buttons.
For more information about the menus,
refer to the sections describing the audio
and telematics systems.
Radio/Media
Navigation
(Depending on equipment)
Driving or Vehicle
(Depending on
equipment)
Activation, deactivation and settings for certain
functions.
The functions are organised in 2 tabs: "
Driving
functions
" and "
Vehicle settings
".
Telephone
Applications
Display of available connected services.
Energy
Access the specific Electric functions
(energy flow, consumption statistics, deferred
charge) organised in the corresponding 3 tabs.
or
Settings
Main settings for the audio system and
touch screen.
Audio system on/off
Volume adjustment/mute
Upper bar
Certain information is displayed permanently in
the upper bar of the touch screen:
– Time and outside temperature (a blue warning
lamp appears if there is a risk of ice).
– Reminder of information from the
RadioMedia
and
Telephone
menus and
navigation instructions (depending on
equipment).
– Notifications.
– Access to the
Settings
.
Energy menu (Electric)
Depending on version, this is accessible either:
– directly, by pressing the button near the
touch screen.
– via the
Applications
menu.
Flow
The page displays a real-time representation of
the electric drive train’s operation.
1.
Active driving mode
2.
Electric motor
3.
Estimated traction battery charge level
4.
Energy flows
The energy flows have a specific colour for each
type of driving:
A.
Blue: energy consumption
B.
Green: energy recovery
Statistics
This page shows electrical energy consumption
statistics.
– Blue bar chart: directly consumed energy
supplied by the traction battery.
– Green bar chart: energy recovered during
deceleration and braking, used to recharge the
battery.
The average result for the current trip is stated in
kWh/100 km.
► You can change the displayed time scale by
pressing the
-
or
+
buttons.
A current trip is any trip of more than 20
minutes without switching off the ignition.
14/02/2022 15:33:05
-------------------------------------------------------------------------------------------------------------------------------------------------------------
26
Dashboard instruments
Charging
This page allows you to programme deferred
charging.
For more information on
Charging the traction
battery (Electric)
, refer to the corresponding
section.
Setting the date and time
With audio system
► Press the
MENU
button for access to the
main menu
.
► Press the "
7
" or "
8
" button to select the
"
Personalisation-configuration
" menu, then
confirm by pressing the
OK
button.
► Press the "
5
" or "
6
" button to select the
Display configuration
menu, then confirm by
pressing the
OK
button.
► Press the "
5
" or "
6
" and "
7
" or "
8
" buttons
to adjust the date and time values, then confirm
by pressing the
OK
button.
With Connect Radio
► Select the
Settings
menu in the upper
banner of the touch screen.
► Select "
Configuration
".
► Select "
Date and time
".
► Select "
Date
" or "
Time
".
► Choose the display formats.
► Change the date and/or time using the
numeric keypad.
► Confirm with "
OK
".
With Connect Nav
Time and date settings are only available if GPS
synchronisation is deactivated.
► Select the
Settings
menu in the
banner of the touch screen.
► Press the "
OPTIONS
" button to access the
secondary page.
► Select "
Setting the time-date
".
► Select the "
Date:
" or "
Time
" tab.
► Set the date and/or time using the numeric
keypad.
► Confirm with "
OK
".
Additional settings
You can choose:
– To change the time zone.
– To change the display format of the date and
time (12h/24h).
– To activate or deactivate the summer time
management function (+1 hour).
– To activate or deactivate GPS synchronisation
(UTC).
The system does not automatically
change between winter and summer time
(depending on the country of sale).
14/02/2022 15:33:05
-------------------------------------------------------------------------------------------------------------------------------------------------------------
27
Access
2
Electronic key with
remote control function
and built-in key
Advice
If one of the doors or the boot is still open
or if the electronic key for the Keyless
Entry and Start system has been left inside
the vehicle, central locking will not take place.
However, if the vehicle is fitted with an alarm,
it will be activated after 45 seconds.
If the vehicle is unlocked but the doors or
boot are not subsequently opened, the
vehicle will automatically lock itself again after
about 30 seconds. If the vehicle is fitted with
an alarm, it will be reactivated automatically.
Automatic door mirror folding and
unfolding can be deactivated by a Fiat
Dealership or a qualified workshop.
As a safety measure, never leave the
vehicle, even for a short time, without
taking the Keyless Entry and Start system’s
electronic key with you.
Be aware of the risk of theft of the vehicle if
the key is present in one of the defined areas
while the vehicle is unlocked.
If a door is not properly closed (except the
right-hand door with side-hinged rear
doors):
– when the vehicle is stationary and engine
running, this warning lamp comes on,
accompanied by a warning message for a few
seconds,
– when the vehicle is moving (at speeds above
6 mph (10 km/h)), this warning lamp comes on,
accompanied by an audible signal and a warning
message for a few seconds.
Remote control key
This allows the central locking or unlocking of the
vehicle using the door lock or from a distance.
It also allows the vehicle to be located, the fuel
filler cap and charging flap to be opened and
closed and the engine to be started or switched
off, as well as providing protection against theft.
The remote control buttons are not active
with the ignition switched on.
Unfolding / Folding the key
► Press this button to unfold or fold the key.
The remote control may be damaged if
you do not press the button.
Keyless Entry and Start
This allows the central locking or unlocking of the
vehicle from a distance.
It is also used to locate and start the vehicle, as
well as providing protection against theft.
Integral key
This is used to lock and unlock the vehicle when
the remote control cannot operate:
– cell battery flat, vehicle battery discharged or
disconnected, etc.
– vehicle located in an area with strong
electromagnetic signals.
14/02/2022 15:33:05
-------------------------------------------------------------------------------------------------------------------------------------------------------------
28
Access
► Keep this button
1
pulled while removing
key
2
from the housing.
If the alarm is activated, the audible
signal triggered on opening a door with
the key (integral with the remote control) will
stop when the ignition is switched on.
Once the built-in key is ejected, always
keep it with you to be able to carry out
the corresponding back-up procedures.
"Keyless Entry and Start" on your
person
It allows the unlocking, locking and starting of the
vehicle while carrying the remote control on your
person in recognition zone "
A
".
In the ignition on (accessories) position,
with the "START/STOP" button, the
hands-free function is deactivated and it is
impossible to open the doors.
For more information on
Starting/switching
off the engine, Keyless Entry and Start
and
in particular the "ignition on" position, refer to
the corresponding section.
Locating the vehicle
This function helps you to spot your vehicle from
a distance, with the vehicle locked:
– The direction indicators flash for approximately
10 seconds.
– The courtesy lamps come on.
► Press this button.
Remote operation of lighting
If fitted to the vehicle.
A short press on this button switches on
the lighting remotely (lighting of
sidelamps, dipped beam headlamps and number
plate lamps).
A second press on the button before the end of
the timed period cancels the remote lighting.
Advice
Remote control
The remote control is a sensitive, high-
frequency device; avoid handling it in your
pocket, due to the risk of unintentionally
unlocking the vehicle.
Avoid pressing the remote control buttons
while out of range of the vehicle, due to
the risk of rendering the remote control
inoperative. It would then be necessary to
reset it.
The remote control does not work when the
key is in the ignition switch, even when the
ignition is switched off.
Anti-theft protection
Do not modify the electronic vehicle
immobiliser, as this might result in
malfunctions.
For vehicles with a key ignition switch,
remember to remove the key and turn the
steering wheel to engage the steering lock.
Locking the vehicle
Driving with the doors locked could make
it more difficult for the emergency services
to enter the passenger compartment in an
emergency.
As a safety precaution, remove the key from
the ignition or take the electronic key with you
when leaving the vehicle, even for a short
time.
14/02/2022 15:33:06
-------------------------------------------------------------------------------------------------------------------------------------------------------------
29
Access
2
Purchasing a second-hand vehicle
Have the key codes memorised by a Fiat
Dealership, to ensure that the keys in your
possession are the only ones able to start the
vehicle.
To preserve the battery charge in the
electronic key and the vehicle's battery,
the "hands-free" functions are set to
hibernation mode after 21 days without use.
To restore these functions, press one of the
remote control buttons or start the engine with
the electronic key in the reader.
For more information on starting with the
Keyless Entry and Start system, refer to the
corresponding section.
Electrical interference
The electronic key may not work if it is
close to an electronic device (e.g. mobile
telephone (switched on or on standby), laptop
computer, strong magnetic fields). If this
occurs, move the electronic key away from
the electronic device.
Accumulations (water, dust, grime, salt,
etc.) on the inner surface of the door
handle may affect detection.
If cleaning the inner surface of the door
handle using a cloth does not restore
detection, contact a Fiat Dealership or a
qualified workshop.
A sudden splash of water (stream of water,
high pressure jet washer, etc.) may be
identified by the system as the desire to open
the vehicle.
Unlocking/Complete or
selective unlocking
What is the purpose of total
or selective unlocking?
Total unlocking unlocks
all
the vehicle’s doors
(front, side and rear).
Selective unlocking unlocks either the
cab
doors,
or the doors of the
loading area
(side and rear).
The separated unlocking system
between
cab
and
loading area
is a
security measure. This prevents access to the
part of the vehicle where the driver is not
present.
Activation/Deactivation
► To
activateselective
unlocking
between the
cab
and the
loading
area
or to
deactivate
selective unlocking and
return to
total
unlocking mode, switch on the
ignition and press this button for more than two
seconds.
An audible signal and, depending on equipment,
a display message, confirm that the request has
been acknowledged.
Selective unlocking between
cab
and
loading area
is activated by default.
14/02/2022 15:33:06
-------------------------------------------------------------------------------------------------------------------------------------------------------------
30
Access
Unlocking/Complete
unlocking
Unlocking is signalled by rapid flashing of
the direction indicators for a few
seconds.
Depending on version, the door mirrors unfold
and the alarm is deactivated.
With the key
► To unlock the vehicle
fully
, turn the key in the
front left-hand door lock towards the front of the
vehicle.
If the vehicle has an alarm, it will not be
deactivated. Opening a door will trigger the
alarm, which can be stopped by switching the
ignition on.
With the remote control
► Depending on equipment,
press one of these buttons to
unlock the vehicle.
Using the remote control with electric
sliding side door(s)
► To
fully
unlock the vehicle and open
the side door, press and hold this button
until the door has opened.
With Keyless Entry and Start on your
person
To unlock the vehicle, the remote control must be
in recognition zone
A
.
► To unlock the vehicle
fully
, pass your hand
behind one of the door handles (front door(s),
manual sliding side door(s) or left-hand side-
hinged door) and then pull the handle to open
the corresponding door.
With electric sliding side door(s)
► With the Keyless Entry and Start on your
person, pass your hand behind the handle
to unlock the vehicle, then pull and release
the handle. This action also causes the
corresponding door to open.
With tailgate
► With the Keyless Entry and Start on your
person, to unlock the
vehicle
, pull the tailgate
handle and then lift it up to open it.
With an opening rear screen in the tailgate
► With the Keyless Entry and Start on your
person, to unlock the vehicle, press the tailgate
opening rear screen unlocking control. The
screen will open slightly; then, lift it up to open it.
14/02/2022 15:33:07
-------------------------------------------------------------------------------------------------------------------------------------------------------------
31
Access
2
Selective unlocking
Unlocking is signalled by rapid flashing of
the direction indicators for a few
seconds.
Depending on version, the door mirrors unfold
and the alarm is deactivated.
With the remote control
► To unlock the
cabin
doors alone,
press this button
once
.
► To unlock the side and rear doors of the
loading area
, press this button a
second time
.
If the vehicle is fitted with this function:
► Press this button to unlock the
loading area
only.
Using the remote control with electric
sliding side door(s)
► To unlock the
loading area
alone
without opening the side door, press the
relevant door button or keep the button pressed
down to open the door.
With Keyless Entry and Start on your
person
► To unlock the
cabin
alone, pass your hand
behind a handle of the front left or right doors,
then pull the handle to open the door.
The door locking state of the
loading
area
remains unchanged.
► To unlock the loading area alone, the remote
control on your person in
recognition zone
A
,
B
or
C
, pass your hand behind a handle of the front
left or right doors, then pull the handle to open
the corresponding door.
Depending on the version, the door
mirrors unfold only when the cabin is
unlocked, the alarm is deactivated.
With electric sliding side door(s)
► With the Keyless Entry and Start on your
person, pass your hand behind the left-hand or
right-hand door handle to unlock the
loading
area
, then pull and release the handle. This
action also causes the corresponding door to
open.
With tailgate
14/02/2022 15:33:07
-------------------------------------------------------------------------------------------------------------------------------------------------------------
32
Access
► With the Keyless Entry and Start on your
person, to unlock the
loading area
, pull the
tailgate handle and then lift it up.
Unlocking is signalled by rapid flashing of
the direction indicators for a few
seconds.
Locking
With the key
► To lock the vehicle
fully
, turn the key in the
front left-hand door lock towards the rear of the
vehicle.
If your vehicle has an alarm, it will not be
activated.
With the remote control
► To lock the vehicle
completely
, press
this button.
With Keyless Entry and
Start on your person
To lock the vehicle, the remote control must be in
recognition zone
A
.
► To lock the vehicle, press the markings on
one of the door handles (front door(s), manual
sliding side door(s) or left-hand side-hinged
door).
With electric sliding side door(s)
► With the Keyless Entry and Start on your
person, to lock the vehicle
fully
, press the
markings on one of the
front
door handles.
With tailgate
► With the Keyless Entry and Start on your
person, press the tailgate locking control to lock
the vehicle.
Depending on version, keeping
the locking controls depressed
closes the windows. If the control is released,
the window stops in its current position.
Ensure that no person or object might
prevent the windows from closing
properly.
Pay particular attention to children when
operating windows.
If the vehicle is not fitted with an alarm,
locking is signalled by fixed lighting of the
direction indicators for approximately two
seconds.
Depending on version, the door mirrors fold at
the same time.
Driving with the doors locked could make
it more difficult for the emergency
services to enter the passenger compartment
in an emergency.
As a safety measure, never leave the vehicle
without taking the remote control with you,
even for a short time.
Deadlocking
Deadlocking deactivates the exterior and
interior door controls, as well as the
central locking button on the dashboard.
The horn remains operational.
You must therefore never leave anyone inside
the vehicle when it is deadlocked.
With the key
► To deadlock the vehicle, turn the key in the
front left-hand door lock towards the rear of the
vehicle.
► Then,
within five seconds
, turn the key
towards the rear again.
14/02/2022 15:33:07
-------------------------------------------------------------------------------------------------------------------------------------------------------------
33
Access
2
With the remote control
► To deadlock the vehicle, press this
button.
► Then
within five seconds after locking
,
press this button again.
Depending on version, the electric door
mirrors fold at the same time.
If the vehicle is not fitted with an alarm,
deadlocking is confirmed by fixed
illumination of the direction indicators for
about two seconds.
With Keyless Entry and Start on your
person
To lock the vehicle, the remote control must be in
recognition zone
A
.
► To lock the vehicle
fully
, press the markings
on one of the door handles (front door(s),
manual sliding side door(s) or left-hand side-
hinged door).
► To deadlock the vehicle, press the markings
again
within five seconds.
With electric sliding side door(s)
► With the Keyless Entry and Start on your
person, to lock the vehicle
fully
, press the
markings on one of the
front
door handles.
► To deadlock the vehicle, press the markings
again
within five seconds.
With tailgate
► With the Keyless Entry and Start on your
person, press the tailgate locking control to lock
the
entire
vehicle.
► To deadlock the vehicle, press the control
again
within five seconds
.
If the vehicle is not fitted with an alarm,
deadlocking is signalled by fixed lighting
of the direction indicators for approximately
two seconds.
Back-up procedures
Lost keys, remote control,
electronic key
Go to a Fiat Dealership with the vehicle's
registration certificate, your personal
identification documents and if possible, the label
bearing the key code.
The Fiat Dealership will be able to retrieve the
key code and the transponder code, enabling a
new key to be ordered.
Complete unlocking/locking
of the vehicle with the key
Use this procedure in the following situations:
– Remote control battery discharged.
– Remote control malfunction.
– Vehicle battery discharged.
– Vehicle in an area subject to strong
electromagnetic interference.
In the first case, change the remote control
battery.
In the second case, reinitialise the remote
control.
Refer to the corresponding sections.
► Insert the key into the door lock.
► Turn the key towards the front/rear to unlock/
lock the vehicle.
► Turn the key towards the rear again within
5 seconds to deadlock the vehicle.
If the vehicle is fitted with an alarm, it will
not be activated when locking with the
key.
If the alarm is activated, the siren sounds
when the door is opened; switch on the
ignition to stop it.
14/02/2022 15:33:07
-------------------------------------------------------------------------------------------------------------------------------------------------------------
34
Access
If the vehicle is unlocked with the key in
the lock
after locking it with the remote
control or the Keyless Entry and Start
system
,
all doors and the boot
are
unlocked.
If the vehicle is unlocked with the key in the
lock
after locking it with the key
, only the
doors (front door and sliding side door(s)) are
unlocked. The side-hinged doors and tailgate
are not unlocked. Switching on the ignition
unlocks them.
Central locking not
functioning
Use these procedures in the following cases:
– Central locking malfunction.
– Battery disconnected or discharged.
In the event of a malfunction of the
central locking system, the battery must
be disconnected to ensure that the vehicle is
locked fully.
Front left-hand door
► Insert the key into the door lock.
► Turn the key towards the rear of the vehicle
to lock it, or towards the front to unlock it.
Front passenger door and sliding
side door
Unlocking
► Pull the interior door opening handle.
Locking
► Open the door.
► For the side door, check that the child lock is
not on. Refer to the corresponding section.
Front passenger door
Sliding side door
► Remove the black cap on the edge of the
door, using the key.
► Insert the key in the aperture without
forcing it, then without turning it, move the latch
sideways towards the inside of the door.
► Remove the key and refit the black cap.
► Close the doors and check from the outside
that the vehicle is locked.
Side-hinged doors
Unlocking
► Use the interior opening handle.
Locking
► If fitted to your vehicle, check that the electric
child lock is not on.
► Open the left-hand side-hinged door.
► Insert the key into the latch aperture on the
edge of the door (without forcing it) and slide the
assembly upwards.
► Remove the key.
► Close the door and check from the outside
that the vehicle is locked.
Unlocking the tailgate
► From inside the vehicle, insert a small
screwdriver into hole
A
on the lock to unlock the
tailgate.
► Move the latch to the left.
If the fault persists after closing again,
the tailgate will remain locked.
14/02/2022 15:33:08
-------------------------------------------------------------------------------------------------------------------------------------------------------------
35
Access
2
Changing the battery
If the battery is flat, this warning lamp
comes on, accompanied by an audible
signal and the display of a message.
Battery type: CR2032/3 volts.
► Unclip the cover by inserting a small
screwdriver in the slot and lift the cover.
► Remove the flat battery from its housing.
► Put the new battery in place, respecting the
polarity. Start by inserting it into the contacts
located in the corner, then clip the cover onto
the unit.
► Reinitialise the remote control.
For more information on
Reinitialising the
remote control
, refer to the corresponding
section.
Do not throw remote control batteries
away, as they contain metals that are
harmful to the environment. Take them to an
approved disposal point.
Reinitialising the remote
control
Following replacement of the battery or in
the event of a fault, it may be necessary to
reinitialise the remote control.
Without Keyless Entry and Start
► Switch the ignition off.
► Turn the key to position
2 (Ignition on)
.
► Immediately press the closed padlock button
for a few seconds.
► Switch off the ignition and remove the key
from the ignition switch.
The remote control is now fully operational
again.
► Insert the mechanical key (incorporated into
the remote control) into the lock to open the
vehicle.
► Place the electronic key against the back-up
reader on the steering column and hold it there
until the ignition is switched on.
►
With a manual gearbox,
place the gear lever
in neutral then fully depress the clutch pedal.
►
With an automatic gearbox or drive
selector
, while in mode
P
, depress the brake
pedal.
► Switch on the ignition by pressing the
"
START/STOP
" button.
If the fault persists after reinitialisation, contact a
Fiat Dealership or a qualified workshop without
delay.
14/02/2022 15:33:08
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст