Freightliner FLA/FLB/FLC/FLD/FLL. Manual — part 6
General Information
Federal Law, Part 205:
Transportation Equipment Noise
Emission Controls
Part 205, Transportation Equipment Noise Emission
Controls, requires the vehicle manufacturer to fur-
nish, with each new vehicle, such written instructions
for the proper maintenance, use, and repair of the
vehicle by the ultimate purchaser to provide reason-
able assurance of the elimination or minimization of
noise-emission-control degradation throughout the
life of the vehicle. In compliance with the law, the
noise emission controls maintenance information in
each applicable group of this manual, in conjunction
with the vehicle service manual, provides these in-
structions to owners.
Recommendations for
Replacement Parts
Replacement parts used for maintenance or repair of
noise emission controls should be genuine Freight-
liner parts. If other than genuine Freightliner parts
are used for replacement or repair of components
affecting noise emission control, the owner should be
sure that such parts are warranted by their manufac-
turer to be equivalent to genuine Freightliner parts in
performance and durability.
Freightliner Noise Emission
Controls Warranty
Refer to the vehicle owner’s warranty information
book for warranty information concerning noise emis-
sion controls.
Tampering with Noise Controls is
Prohibited
Federal law prohibits the following acts or the caus-
ing thereof:
1.
The removal or rendering inoperative by any per-
son (other than for purposes of maintenance,
repair, or replacement) of any device or element
of design incorporated into any new vehicle for
the purpose of noise control, prior to its sale or
delivery to the ultimate purchaser, or while it is in
use.
2.
The use of the vehicle after such device or ele-
ment of design has been removed or rendered
inoperative by any person.
Among those acts presumed to constitute tam-
pering are the acts listed below:
A. Removal of engine noise-deadening panels.
B. Removal of cab-tunnel or hood noise-
deadening panels.
C. Removal of, or rendering inoperative, the en-
gine speed governor so as to allow engine
speed to exceed manufacturer’s specifica-
tions.
D. Removal of, or rendering inoperative, the fan
clutch, including bypassing the control on
any thermostatic fan drive to cause it to op-
erate continuously.
E. Removal of the fan shroud.
F.
Removal of, or rendering inoperative, ex-
haust components, including exhaust pipe
clamping.
G. Removal of air intake components.
Maintenance Instructions
Scheduled intervals are in the maintenance tables in
this group. A "Verification of Inspections Log (Groups
01, 20, and 49)" follows, and should be filled in each
time noise emission controls on the vehicle are main-
tained or repaired.
General Information
00
Noise Emission Controls Maintenance: 00–12
00/25
Verification of Inspections Log
Verification of Inspections Log, Group 01
Verification of Inspections Log — Group 01 — Engine Rear Supports and Engine Noise Panels
Date
Mileage
Item
Cost
Maintenance Facility
Verification of Inspections Log, Group 20
Verification of Inspections Log — Group 20 — Fan Drive
Date
Mileage
Item
Cost
Maintenance Facility
General Information
00
Verification of Inspections Log: 00–13
00/26
Verification of Inspections Log, Group 49
Verification of Inspections Log — Group 49 — Exhaust System Components
Date
Mileage
Item
Cost
Maintenance Facility
General Information
00
Verification of Inspections Log: 00–13
00/27
When You Know U.S.
Customary
Multiply
By
To Get Metric
When You
Know Metric
Multiply
By
To Get U.S. Customary
Length
inches (in)
25.4
millimeters (mm)
0.03937
inches (in)
inches (in)
2.54
centimeters (cm)
0.3937
inches (in)
feet (ft)
0.3048
meters (m)
3.281
feet (ft)
yards (yd)
0.9144
meters (m)
1.094
yards (yd)
miles (mi)
1.609
kilometers (km)
0.6215
miles (mi)
Area
square inches (in
2
)
645.16
square millimeters (mm
2
)
0.00155
square inches (in
2
)
square inches (in
2
)
6.452
square centimeters (cm
2
)
0.155
square inches (in
2
)
square feet (ft
2
)
0.0929
square meters (m
2
)
10.764
square feet (ft
2
)
Volume
cubic inches (in
3
)
16387.0
cubic millimeter (mm
3
)
0.000061
cubic inches (in
3
)
cubic inches (in
3
)
16.387
cubic centimeters (cm
3
)
0.06102
cubic inches (in
3
)
cubic inches (in
3
)
0.01639
liters (L)
61.024
cubic inches (in
3
)
fluid ounces (fl oz)
29.54
milliliters (mL)
0.03381
fluid ounces (fl oz)
pints (pt)
0.47318
liters (L)
2.1134
pints (pt)
quarts (qt)
0.94635
liters (L)
1.0567
quarts (qt)
gallons (gal)
3.7854
liters (L)
0.2642
gallons (gal)
cubic feet (ft
3
)
28.317
liters (L)
0.03531
cubic feet (ft
3
)
cubic feet (ft
3
)
0.02832
cubic meters (m
3
)
35.315
cubic feet (ft
3
)
Weight/Force
ounces (av) (oz)
28.35
grams (g)
0.03527
ounces (av) (oz)
pounds (av) (lb)
0.454
kilograms (kg)
2.205
pounds (av) (lb)
U.S. tons (t)
907.18
kilograms (kg)
0.001102
U.S. tons (t)
U.S. tons (t)
0.90718
metric tons (t)
1.1023
U.S. tons (t)
Torque/Work Force
inch–pounds (lbf·in)
11.298
Newton–centimeters (N·cm)
0.08851
inch–pounds (lbf·in)
foot–pounds (lbf·ft)
1.3558
Newton–meters (N·m)
0.7376
foot–pounds (lbf·ft)
Pressure/Vacuum
inches of mercury (inHg)
3.37685
kilo Pascals (kPa)
0.29613
inches of mercury (inHg)
pounds per square inch (psi)
6.895
kilo Pascals (kPa)
0.14503
pounds per square inch (psi)
Table 2, Metric/U.S. Customary Conversion
General Information
00
Metric/U.S. Customary Conversion Tables: 00–14
00/28
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст