Kia Sedona (2008 year). Manual — part 155
3. Select "Diagnostic Trouble Codes (DTC s)" mode and monitor "DTC Status" parameter.
4. Is the DTC B1605 present?
YES
Go to TERMINAL AND CONNECTOR INSPECTION procedure.
NO
Fault is intermittent caused by poor contact in the sensor's and/or ECM's connector or was repaired and
ECM memory was not cleared. Thoroughly check connectors for looseness, poor connection, bending,
corrosion, contamination, deterioration, or damage. Repair or replace as necessary and then go to
"VERIFICATION OF VEHICLE REPAIR" procedure.
TERMINAL AND CONNECTOR INSPECTION
Refer to DTC B1102.
SIGNAL CIRCUIT INSPECTION
1. Check CAN high communication circuit
1. Ignition "ON" and Engine "OFF".
2. Connect scan tool and select VEHICLE SCOPEMETER function.
3. Measure waveform between terminal "BCM-IF-30" of IPM and chassis ground.
Specification: CAN communication waveform is displayed
Fig. 73: Measuring Waveform Between Terminal BCM-IF-30 Of IPM And Chassis Ground
Courtesy of KIA MOTORS AMERICA, INC.
4. Is the measured waveform within specifications?
The existence of CAN communication waveform itself shows there's no trouble in CAN
communication circuit. If there's any short in harness, no signal is detected.
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:17 PM
Page 89
© 2006 Mitchell Repair Information Company, LLC.
YES
Go to step 2.
NO
Check for short circuit in signal harness. Repair as necessary and go to "VERIFICATION
VEHICLE REPAIR" procedure.
2. Check CAN low communication circuit
1. Ignition "ON" and Engine "OFF".
2. Connect scan tool and select VEHICLE SCOPEMETER function.
3. Measure waveform between terminal "BCM-IF-39" of BCM ECU and chassis ground.
Specification: CAN communication waveform is displayed
Fig. 74: Measuring Waveform Between Terminal BCM-IF-39 Of BCM ECU And Chassis
Ground
Courtesy of KIA MOTORS AMERICA, INC.
4. Is the measured waveform within specifications?
The existence of CAN communication waveform itself shows there's no trouble in CAN
communication circuit. If there's any short in harness, no signal is detected
YES
Go to "COMPONENT INSPECTION" procedure.
NO
Check for short circuit in signal harness. Repair as necessary and go to "VERIFICATION
VEHICLE REPAIR" procedure.
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:17 PM
Page 90
© 2006 Mitchell Repair Information Company, LLC.
POWER SUPPLY CIRCUIT INSPECTION
1. Check for open or short in power harness
1. Ignition "OFF".
2. Connect DDM
3. Measure voltage value between terminal "D01-1-13" of DDM and chassis ground.
Specification: 9-16V
Fig. 75: Measuring Voltage Value Between Terminal D01-1-13 Of DDM And Chassis Ground
Courtesy of KIA MOTORS AMERICA, INC.
4. Is the measured voltage within specifications?
YES
Go to "COMPONENT INSPECTION" procedure.
NO
Check for open or short in power harness. Repair as necessary and go to "VERIFICATION OF
VEHICLE REPAIR" procedure.
COMPONENT INSPECTION
1. Check DDM
1. Connect scan tool to Data Link Connector (DLC).
2. Ignition "ON" & engine "OFF".
3. Substitute with a known-good DDM and Check if the DTC is erased.
4. Is the DTC erased?
YES
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:17 PM
Page 91
© 2006 Mitchell Repair Information Company, LLC.
Substitute with a known-good DDM and check for proper operation.
If the problem is corrected, replace DDM and then go to "VERIFICATION OF VEHICLE
REPAIR" procedure.
NO
Go to step 2.
2. Check IPM
1. Connect scan tool to Data Link Connector (DLC).
2. Ignition "ON" & engine "OFF".
3. Substitute with a known-good IPM and Check if the DTC is erased.
4. Is the DTC erased?
YES
Substitute with a known-good IPM and check for proper operation.
If the problem is corrected, replace IPM and then go to "VERIFICATION OF VEHICLE
REPAIR" procedure.
NO
Check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration,
or damage.
Repair or replace as necessary and then go to "VERIFICATION OF VEHICLE REPAIR"
procedure.
VERIFICATION OF VEHICLE REPAIR
Refer to DTC B1102.
DTC B1606 LOST COMMUNICATION WITH ADM, BUS FAILURE
COMPONENT LOCATION
Refer to DTC B1605.
GENERAL DESCRIPTION
Refer to DTC B1602.
DTC DESCRIPTION
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:17 PM
Page 92
© 2006 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст