Kia Sedona (2008 year). Manual — part 180
Replace "defogger for test" with "new defogger" and go to "VERIFICATION OF VEHICLE
REPAIR".
NO
Go to step 2.
2. Check RAM
1. Connect scan tool to Data Link Connector (DLC).
2. Ignition "ON" & engine "OFF"
3. Check if DTC is erased after replacing RAM with "RAM for test".
4. Is the DTC erased?
YES
Replace "RAM for test" with "new RAM" and go to "VERIFICATION OF VEHICLE
REPAIR".
NO
Check connecting condition of connector and go to "VERIFICATION OF VEHICLE REPAIR".
VERIFICATION OF VEHICLE REPAIR
After a repair, it is essential to verify that the fault has been corrected.
1. Connect scan tool and select "Diagnostic Trouble Codes (DTCs)" mode and then clear DTC.
2. Operate the vehicle within DTC Enable conditions in General information.
3. Are any DTCs present?
YES
Go to the applicable troubleshooting procedure.
NO
System is performing to specification at this time.
DTC B2119 WINDSHIELD DEFOG RELAY FAILURE
COMPONENT LOCATION
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:19 PM
Page 189
© 2006 Mitchell Repair Information Company, LLC.
Fig. 159: Locating Front Wiper Motor & Windshield Defogger Connector
Courtesy of KIA MOTORS AMERICA, INC.
GENERAL DESCRIPTION
FAM is a part of BCM with DDM, ADM, IPM, RAM, IMS and Cluster module. Each part of BCM is
connected to one another through CAN communication line for efficient communication. Those modules
control front/rear, driver/passenger seat, cluster with electrical signal and they share information with other
modules. FAM (Front Area Module) set up at engine room controls various lamps (fog lamp, headlamp, stop
lamp, turn signal lamp), wiper and performs system error checking as well. Received wind shield defogger
switch signal from IPM through CAN line, FAM controls wind shield defogger.
DTC DESCRIPTION
The ECM sets DTC B2119 if open/short in wind shield defogger circuit or relay failure is detected.
DTC DETECTING CONDITION
DTC DETECTING CONDITION
MONITOR DTC STATUS
1. Connect scan tool to Data Link Connector (DLC).
2. Ignition "ON" & engine "OFF" & FAM: "ON".
3. Select "Diagnostic Trouble Codes (DTCs) "mode and monitor "DTC Status" parameter.
Item
Detecting Condition
Possible Cause
DTC Strategy
Resistance check
Open in power circuit
RAM failure
Enable Conditions
IGN: ON, ENG: OFF
Threshold value
infinity ohms
Detecting time
-
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:19 PM
Page 190
© 2006 Mitchell Repair Information Company, LLC.
Fig. 160: Identifying Scan Tool Display - Diagnostic Trouble Codes (DTCs)
Courtesy of KIA MOTORS AMERICA, INC.
4. Is the DTC B2119 present?
YES
Go to TERMINAL AND CONNECTOR INSPECTION.
NO
Fault is intermittent caused by poor contact in the sensor's and/or ECM's connector or was repaired and
ECM memory was not cleared. Thoroughly check connectors for looseness, poor connection, bending,
corrosion, contamination, deterioration, or damage. Repair or replace as necessary and then go to
"VERIFICATION OF VEHICLE REPAIR" procedure.
TERMINAL AND CONNECTOR INSPECTION
1. Electrical systems consist of a lot of harness and connectors, poor connection of terminals can cause
various problems and damage of component.
2. Check poor connection, bedding, corrosion, contamination, deformation of connector and it terminals.
3. Is any problem found?
YES
Repair if necessary and go to "VERIFICATION OF VEHICLE REPAIR".
NO
Go to POWER SUPPLY CIRCUIT INSPECTION.
POWER SUPPLY CIRCUIT INSPECTION
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:19 PM
Page 191
© 2006 Mitchell Repair Information Company, LLC.
1. Check open in power circuit
1. Ignition "ON" & engine "OFF".
2. Measure the resistance between wind shield defogger power circuit of FAM (BEC-FE-3) and wind
shield defogger (E04-2).
Specification: 0 ohms.
Fig. 161: Measuring Resistance Between Wind Shield Defogger Power Circuit Of FAM
(BEC-FE-3) And Wind Shield Defogger (E04-2)
Courtesy of KIA MOTORS AMERICA, INC.
3. Is the measured resistance within the specification?
YES
Go to step 2.
NO
Repair open in power circuit and go to "VERIFICATION OF VEHICLE REPAIR".
2. Check short in power circuit
1. Ignition "ON" & engine "OFF".
2. Disconnect wind shield defogger.
3. Measure the resistance between wind shield defogger power circuit of FAM (BEC-FE-3) and
chassis ground.
Specification: infinity ohms
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:19 PM
Page 192
© 2006 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст