Kia Carnival (2007 year). Manual — part 304

Head Lamps Low Beam Function

1. Necessary conditions to switch ON :

a. By putting the Head lamp switch in position 'Head lamp Low Beam' or Auto light activation or DRL activation.

2. Necessary conditions to switch OFF :

a. If they are released by the Head lamp switch (Auto light function deactivated) and if the DRL function is

deactivated

b. If the Auto light function is active but the Auto light sensor signal status is not 'HL ON'.

3. Functional diagram

Head Lamps High Beam Function

1. Necessary conditions to switch ON :

a. By pushing down the High Beam lever switch if

a. the Head lamp switch is in position 'Head lamp Low Beam' or the Head lamps Low Beam have been turned ON

by the Auto light function.

b. By pulling the High Beam lever switch toward the driver (Flash to pass activation)

c. By the DRL function activation for Canada.

2. Necessary conditions to switch OFF :

a. By pulling back the High Beam lever switch (manual reset by the driver) or

b. If the Head lamps Low Beam are turned OFF or if the Auto light function is active but the Auto light Sensor

signal status is not 'HL ON') or

c. By releasing the Flash To Pass activation and

d. If the DRL function is deactivated for Canada.

3. Functional diagram

Turn Signal And Side Repeater Lamps Function

1. Necessary conditions to switch ON(if they are standard) :

a. By activation of Crash Unlock

b. During the opening / closing of the Tail gate by the PTG Flasher input

c. With the Remote Keyless Entry to lock / unlock the vehicle

d. By alarm activation

e. By panic activation with the Remote Keyless Entry

f. By activation of the Hazard Lamp by the hazard switch and ignition is position OFF, ACC or RUN

g. By using the turn lever switch with the ignition switch in the ON position.

2. Necessary conditions to switch OFF(if they are standard) :

a. Ignition switch in OFF position for deactivation of crash unlock flashing

b. Deactivation of the alarm or at the end of the alarm flashing sequence

c. Deactivation of panic sequence with pushing any button of the Remote Keyless Entry or at the end of the panic

flashing sequence

d. Turn lever switch command in OFF postion or ignition switch in OFF, ACC or START position to stop turn lever

flashing.

e. The hazard switch in OFF position or ignition switch in position START to stop the Hazard flashing.

f. At the end of the Lock, Unlock and PTG flashing sequence.

3. During the start up of the vehicle (ignition key in position START) :

a. The Turn signal lamps activated by the turn lever switch are temporarily turned OFF. If the time duration in Start

position is more than 10seconds and engine running, the Turn signal lamps are managed again as if the ignition
key was in ON position,

b. The flashing sequence of the hazard lamps is immediately stopped if they have been activated by the hazard

button. If the time duration in Start position is more than 10seconds and engine running, the flashing sequence
of the hazard lamps are managed again as if the ignition key was in RUN position,

c. The flashing sequence of the hazard lamps is not stopped if they have been activated by a crash unlock.

4. Functional diagram

Front Fog Lamps Function

1. Necessary conditions to switch ON :

a. By using the stalk: Head lamp switch in position 'Head lamp Low Beam' and Front Fog lamp sw ON

b. When Auto light function activated and Auto light Sensor signal status is 'HL ON' and Front Fog lamp sw ON

2. Necessary conditions to switch OFF :

a. When Auto light function activated and Auto light Sensor signal status is not ON

b. When Front fog lamp sw OFF.

3. Functionnal Diagram

Backup Lamps Function

1. Necessary conditions to switch ON :

a. When inhibit sw 'R' read by FAM is active and transmitted to RAM by CAN signal.

2. Necessary conditions to switch OFF :

a. When inhibit sw 'R' read by FAM is not active and transmitted to RAM by CAN signal.

3. Functional diagram

Stop Lamps Function

1. Necessary conditions to switch ON the stop lamps:

a. Pushing on the brake pedal.

2. Necessary conditions to switch OFF the stop lamps:

a. Releasing the brake pedal.

3. Functional diagram

Auto Light Function

1. The Auto light function is active when the Head lamp switch is positioned to 'Auto' and the Key is in RUN position.

The auto light sensor is powered on the status ACC, START and RUN of the key position. Based on the Auto light
sensor values corresponding to the exterior brightness level, it controls automatically the lighting of the Park and tail
lamps or / and the Head lamps Low Beam depending on the country.

2. Auto light Sensor detection table

Mode

Tail Lamps

Head Lamps Low Beam

Lux (Lux)

Voltage(V)

Lux (Lux)

Voltage(V)

ON

< 24 ± 5.2

<1.77 ± 0.08V

Same as Tail lamps

OFF

> 48 ± 10.5

> 3.47 ± 0.1V

Same as Tail lamps

Drl Function

1. The Auto DRL function operates the Head lamps High Beam at 50% of full illumination.

The park and tail are managed by the auto light sensor.
The Auto DRL function is active if:

a. The ignition switch is on RUN position

b. The engine is running.

c. The Park brake switch is OFF.

2. The DRL function is inactive when one of above conditions is released.

When the DRL function is active, the Head lamps High Beam can't be turned ON, except for the Flash To Pass
activation.