Kia Carnival (2009+). Manual — part 307
Triple pressure switch system
The cause is probably a defective dual pressure switch circuit or a
defective TCM(PCM).
- Malfunction of the triple pressure switch
- Malfunction of connector
- Malfunction of A/C system
- Malfunction of the TCM(PCM)
Vehicle speed sensor system
The cause is probably a defective vehicle speed sensor circuit or a
defective TCM(PCM).
- Malfunction of the vehicle speed sensor
- Malfunction of connector
- Malfunction of the TCM(PCM)
DTC TROUBLESHOOTING INDEX
No.
Code
Item
MIL
Remark
1
P0707
TRANSAXLE RANGE SWITCH CIRCUIT LOW INPUT
ON
2
P0708
TRANSAXLE RANGE SWITCH CIRCUIT HIGH INPUT
ON
3
P0711
TRANSAXLE FLUID TEMPERATURE SENSOR RATIONALITY
ON
4
P0712
TRANSAXLE FLUID TEMPERATURE SENSOR CIRCUIT LOW INPUT
ON
5
P0713
TRANSAXLE FLUID TEMPERATURE SENSOR CIRCUIT HIGH INPUT
ON
6
P0717
A/T INPUT SPEED SENSOR CIRCUIT - OPEN or SHORT(GND)
ON
7
P0722
AT OUTPUT SPEED SENSOR CIRCUIT - OPEN or SHORT(GND)
ON
8
P0731
GEAR 1 INCORRECT RATIO
ON
9
P0732
GEAR 2 INCORRECT RATIO
ON
10
P0733
GEAR 3 INCORRECT RATIO
ON
11
P0734
GEAR 4 INCORRECT RATIO
ON
12
P0741
TORQUE CONVERTER CLUTCH STUCK OFF
ON
13
P0742
TORQUE CONVERTER CLUTCH STUCK ON
ON
14
P0743
TORQUE CONVERTER CLUTCH CONTROL SOLENOID VALVE - OPEN or
SHORT(GND)
ON
15
P0748
VFS SOLENOID
OFF
16
P0750
LOW and REVERSE SOLENOID VALVE CIRCUIT - OPEN or SHORT(GND)
ON
17
P0755
UNDER DRIVE SOLENOID VALVE CIRCUIT - OPEN or SHORT(GND)
ON
18
P0760
SECOND SOLENOID VALVE CIRCUIT - OPEN or SHORT(GND)
ON
19
P0765
OVERDRIVE SOLENOID VALVE CIRCUIT - OPEN or SHORT(GND)
ON
20
P0885
A/T CONTROL RELAY - OPEN or SHORT(GND)
ON
21
P0890
TCM power Relay sense circuit low
ON
22
P0891
TCM power Relay sense circuit High
ON
Failsafe
Activation and deactivation of error failsafe is coordinated Error failsafe Management.
Once Error failsafe is activated, it will be kept until ignition key OFF.
In every new TCM start, TCM start with No Error failsafe and No Error present.
0. Mechanical Limp Home Mode
• Switch off A/T relay
1. Electrical Limp Home Mode
• Keep 2nd / 3rd gear
2. Prohibit Intelligent Shift
• Fuzzy SAT(Siements Adaptive Transmission) shift pattern (Medium Driver, Sporty Driver) will not be used
3. Prohibit Adaptive Control
• No learning is done
6. Prohibit Torque Reduction Request
• No torque reduction is sent to ECU
7. Prohibit Lockup Control
• Stay in non-lockup control state
8. Substitute Input Value Oil Temperature
• Set oil temperature(tf) to 80° C (192°F)
9. Substitute Value Speed Ratio
• Set speed ratio to 0.7
10. Substitute CAN Input Value
• Set engine torque to 42
%
• Set throttle position to 50
%
• Set accelerator pedal signal to 50
%
• Set engine speed (Ne) to 3000 rpm
• Set vehicle speed to 0 km/h
• Set status of air condition relay to OFF
11. Prohibit VFS control
• Stop the Line Pressure Control till IG Off
Failsafe according to the DTC
- Refer the detail description in the previous page for the indicated number on the ‘Failsafe’ column.
Items
Type of error
Failsafe
OBD-II
relevant
DTC
DTC
Oil temperature sensor
Short to ground
2, 3, 7, 8, 11
P0712
P0712
Open or short to B+
P0713
P0713
Stuck signal
P0711
P0711
Sensor fail
P0711
P0711
PG-A
Short to ground
1,11
P0717
P0717
Open or short to B+
PG-B
Short to ground
P0722
P0722
Open or short to B+
Sensor fail
P0721
P0721
Brake switch
Open
2
!
P0713
Short to B+
LR Solenoid valve
Short to B+
0,11
P0750
P0750
Open or short to ground
2nd Solenoid valve
Short to B+
P0760
P0760
Open or short to ground
UD Solenoid valve
Short to B+
P0755
P0755
Open or short to ground
OD Solenoid valve
Short to B+
P0765
P0765
Open or short to ground
Open or short to B+
P0765
P0765
DCC Solenoid valve
Short to B+
P0743
P0743
Open or short to ground
1st speed asynchronous
Synchronous error
0,11
P0731
P0731
2nd speed asynchronous
Synchronous error
P0732
P0732
3rd speed asynchronous
Synchronous error
P0733
P0733
4th speed asynchronous
Synchronous error
P0734
P0734
Reverse speed asynchronous
Synchronous error
!
!
CAN
No ID from ECM
2,3,6,7,9,10,11
!
P1604
CAN BUS off
!
P1603
Damper clutch
Abnormal system
7
P0741
P0741
A/T relay
Short to ground or open
0,11
P0885
P0885
Inhibitor switch
Short to ground or open
!
P0707
P0707
Short to B+ or short between switches
P0708
P0708
VFS
Short to B+
11
!
P0748
Short to ground
0,11
Open
11
CKP sensor
Sensor error
Ne=3,000rpm
7,9
!
!
TPS sensor
Sensor error
TPS=50
%
!
!
SERVICE DATA LIST(WITH SCAN TOOL)
No.
ITEM NAME
UNIT
DATA
Data Description
Failure
1
ENGINE RPM
rpm
700 rpm Current Engine rpm
0 rpm
2
VEHICLE SPEED
km/h
0km/h
Current Vehicle speed
0km/h
3
THROTTLE
P.SENSOR
%
12.5%
Current TPS open angle
0%
4
INPUT SPEED(PG-A)
rpm
700 rpm
Input speed rpm. Always output
rpm when turning start ON
0 rpm
5
OUTPUT SPEED(PG-
B)
rpm
0 rpm
Output speed rpm. Always output
rpm when driving
0 rpm
6
DCC(TCC) SOLENOID
DUTY
%
0%
Control 0% " 100% when
operating Damper Clutch
7
DAMPER CLUTCH
SLIP
rpm
260 rpm Current Damper clutch slip ratio
0 rpm
8
LR SOLENOID DUTY
%
100%
Control 100% " 0% when
operating brake
0%
9
UD SOLENOID DUTY
%
100%
Control 100% " 0% when
operating clutch
0%
10
2ND SOLENOID DUTY
%
100%
Control 100% " 0% when
operating clutch
0%
11
OD SOLENOID DUTY
%
100%
Control 100% " 0% when
operating clutch
0%
12
VFS SOLENOID DUTY
%
0~400
%
!
13
OIL TEMPERATURE
°C
40°C
Current Oil temperature
80°C
14
SHIFT POSITION
N,P,REV/1st G/…/5th
G
D
Current shift position
P, N
15
SELECT LEVEL
P,N/R/D/SPORTS
D
Current shift lever position
P, N
16
A/CON SWITCH
OFF/ON/-/NOT
SUPP
OFF
-
17
IDLE STATUS
OFF/ON/-/NOT
SUPP
ON
When idling, ON
18
BRAKE SWITCH
OFF/ON/-/NOT
SUPP
ON
When braking, ON
19
AUTO CRUISE
SWITCH
OFF/ON/-/NOT
SUPP
20
AUTO CRUISE
RELEASE
!
!
21
SPORT MODE
SELECT SW
OFF/ON/-/NOT
SUPP
ON
When selecting sport mode, ON
22
SPORT MODE UP SW
OFF/ON/-/NOT
SUPP
ON
When Selecting Sport mode up, ON
23
SPORT MODE DOWN
SW
OFF/ON/-/NOT
SUPP
ON
When selecting sport mode down,
ON
24
A/T CONTROL RELAY
VOLT
V
12.9V
0V
25
ENGINE TORQUE
%
20%
26
HIVEC MODE
A/B/C/D/E/F/G/H/I/J/K
F
A/B/C/D is control mode, F is
release mode
F
HIVEC -SAT(SIEMENS ADAPTIVE TRANSMISSION CONTROL) Mode (Shift Patten)
Shift patten
Description(Help)
SCAN DISPLAY
ECONOMY
Economy Driver shift patten for flat road
A
MEDIUM
Shift patten for medium road
B
SPORTS
Shift patten for sport road
C
LOAD 1
Shift patten for low land, slow grade and slope
D
LOAD 2
Shift patten for low land, steep grade and slope
E
LOAD 3
Shift patten for downhill road
F
LOAD 1 HI ALT
Shift patten for high land, steep grade and slope
G
LOAD 2 HI ALT
Shift patten for low land, steep grade and slope
H
HI TEMP
Shift patten for high temperture ATF
I
WARM UP
Shift patten for exhaust gas decrease
J
HOLD
Shift patten for when hold, switch on
K
Actuator inspection
NO
ITEM NAME
Actuator Driving
Condition
1
LR SOLENOID(SCSV A)
1. IG Key ON
2. Inhibitor SW normal
3. P range
2
UD SOLENOID(SCSV B)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст