Suzuki Grand Vitara JB416 / JB420 / JB419. Manual — part 496
9D-10 Wipers / Washers:
• For automatic stop operation
a. Connect battery positive (+) terminal to
terminal “1” and its negative (–) terminal to
body ground and let the motor turn.
b. Connect terminal “2” and “3” by a jumper wire.
c. Observe the motor (4) turns once again then
stops at a specified position as shown.
d. Repeat Step a. to c. several times and check
that the motor stops at the specified position
every time.
If check result is not satisfied, replace motor.
Windshield Wiper and Washer Switch Removal
and Installation
S6JB0A9406008
Removal
1) Disconnect negative (–) cable at battery.
2) Remove steering column hole cover (1).
3) Remove steering column covers (2).
Turn steering wheel to access steering column cover
rear end screws (3).
4) Remove windshield wiper and washer switch (1)
from combination switch assembly (2) and
disconnect its coupler (3).
Installation
Reverse removal procedure.
5. Mark
5
4
1
3
2
I5JB0A940019-01
1
2
3
3
I5JB0A940020-02
1
2
3
I4RS0B940008-01
Wipers / Washers: 9D-11
Windshield Wiper and Washer Switch
Inspection
S6JB0A9406009
Windshield Wiper and Washer Switch
Check for continuity between terminals at each switch
position. If check result is not as specified, replace
switch.
Intermittent Wiper Relay Circuit
1) Turn the windshield wiper switch to “INT” position.
2) Connect battery positive (+) terminal to terminal “5”
and its negative (–) terminal to terminal “2”.
3) Connect voltmeter positive lead to terminal “4” and
its negative lead to terminal “2”.
4) Check that the voltmeter indicates the battery
voltage (10 – 14 V).
5) Connect terminal “3” and terminal “5” by a jumper
wire.
[A]: RH steering vehicle without rear fog light
[B]: Other than RH steering vehicle without rear fog light
[C]: Terminal
[D]: Wiper switch
[E]: Washer switch
OFF
INT
6
5
4
3
MIST
OFF
1
2
ON
LO
HI
6 5 4 3 2 1
1 2 3 4 5 6
[A]
[B]
[C]
[D]
[E]
[C]
I5JB0D940001-01
[A]: RH steering vehicle without rear fog light
[B]: Other than RH steering vehicle without rear fog light
V
2
3
4
5
2
3
4
5
[B]
[A]
I5JB0D940002-02
9D-12 Wipers / Washers:
6) Disconnect end of the jumper wire from terminal “5”.
7) Connect disconnected jumper wire end to terminal
“2”, then check that voltage between terminal “4” and
terminal “2” changes as shown.
If check result is not satisfied, replace switch.
Washer Linked Circuit
1) Make sure that front wiper switch is at “OFF”
position.
2) Connect battery positive (+) terminal to terminal “5”
and its negative (–) terminal to terminal “2”.
3) Connect voltmeter positive lead to terminal “4” and
its negative lead to terminal “2”.
4) When front washer switch is ON, check that voltage
changes as shown in figure.
If check result is not satisfied, replace switch.
[A]: RH steering vehicle without rear fog light
[B]: Other than RH steering vehicle without rear fog light
[C]: Voltage
[D]: INT time control switch position
[E]: 1.6
± 1 sec.
[F]: 10.7
± 5 sec.
V
INT
TIME
INT
TIME
10-14V
0V
10-14V
0V
2
3
4
5
2
3
4
5
[B]
[A]
[C]
[D]
[E]
[F]
I5JB0D940003-02
[A]: RH steering vehicle without rear fog light
[B]: Other than RH steering vehicle without rear fog light
[C]: Wiper switch
[D]: Voltage
[E]: Approx. 2.2 sec.
[F]: Approx. 0.3 sec.
V
2
4
5
2
4
5
[B]
[A]
ON
OFF
High
Low
[E]
[F]
[C]
[D]
I5JB0D940004-02
Wipers / Washers: 9D-13
Rear Wiper and Washer Switch Removal and
Installation
S6JB0A9406010
For removal and installation, refer to “Windshield Wiper
and Washer Switch Removal and Installation”.
Rear Wiper and Washer Switch Inspection
S6JB0A9406011
Check for continuity between terminals at each switch
position. If check result is not as specified, replace
switch.
Rear Wiper Relay Removal and Installation
S6JB0A9406012
Removal
1) Disconnect negative (–) cable at battery.
2) Remove rear end door trim from rear end door
referring to “Rear End Door Lock Assembly Removal
and Installation in Section 9F”.
3) Remove rear wiper relay (1).
Installation
Reverse removal procedure for installation.
Rear Wiper Relay Inspection
S6JB0A9406013
1) Check that there is no continuity between terminal
“4” and “5”. If there is continuity, replace relay.
2) Check that there is continuity between terminal “3”
and “5”. If there is no continuity, replace relay.
3) Connect battery positive (+) terminal to terminal “2”
of relay.
4) Connect battery negative (–) terminal to terminal “1”
of relay.
5) Check continuity between terminal “4” and “5”. If
there is no continuity when relay is connected to the
battery, replace relay.
[A]: RH steering vehicle without rear fog light
[B]: Other than RH steering vehicle without rear fog light
OFF
[C]
[D]
4
3
1
2
1
2
3
4
[A]
[B]
1
2 3
4
[C]
[D]
[E]
[F]
[E]
[F]
I5JB0D940005-01
1
I5JB0A940021-01
“5”
“2”
“1”
“4”
“3”
I5JB0A940022-01
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст