Suzuki Grand Vitara JB416 / JB420 / JB419. Manual — part 306
5A-15 Automatic Transmission/Transaxle:
Electronic Shift Control System Wiring Diagram
S6JB0A5102004
13
34
34
34
34
11
12
35
P
R
N
D
2
L
14
5V
12V
12V
12V
12V
BLK
BLK/ORN
BLK/ORN
IG11
BLK/RED
BLK/WHT
+BB
WHT
16
21
17
18
20
12V
19
23
30
25
24
26
27
28
29
WHT
WHT
RED
WHT
RED
RED
6
5
16 15 14 13 12 11
4 3
24 23
21
22
10 9
8
7
2
1
19
20
18 17
E92
17 16
26 25
15 14
6
5
3
4
2
13 12
23 22
24
11 10 9
21 20 19
8 7
18
1
E93
[A]
32
33
RED
BLU
WHT
P
N
GRN
YEL/BLK
ORN
GRN/RED
YEL/RED
BRN/RED
GRN/YEL
PPL/WHT
E92-11
E92-12
E92-16
E92-15
E92-4
E92-2
E92-1
E92-23
E92-6
E92-24
E92-5
E92-3
RED
YEL/GRN
PNK/BLU
PNK/GRN
PNK/WHT
YEL/BLK
YEL/RED
GRN/ORN
GRN/WHT
E92-20
E92-10
E93-4
E93-23
E93-20
E93-1
E93-8
E93-7
E93-19
E93-18
E92-17
E92-7
5
IG11
12V
31
PPL/WHT
34
WHT
RED
34
WHT
RED
34
WHT
RED
WHT
RED
2.5V
WHT
ORN
1
2
E93-5
E93-14
2.5V
BLU
PNK
E93-6
E93-16
15
6
9
BLK/WHT
3
6
4
5
7
8
10
I6JB0A510001-02
Automatic Transmission/Transaxle: 5A-16
[A]: TCM connector (viewed from
harness side)
9. P/N mode switch
18. Shift solenoid valve-B
27. “IG COIL” fuse
1. Output shaft speed sensor
10. “3” position switch
19. TCC pressure control solenoid
valve
28. “ST SIG” fuse
2. Input shaft speed sensor
11. Shift lock solenoid
20. Pressure control solenoid valve
29. “ST” fuse
3. Combination meter
12. Brake light switch
21. Valve body assembly
30. AT relay included in integration
relay No.2 in main fuse box
4. ABS/ESP
® control module
13. Transmission range switch
22. —
31. Starting motor relay
5. ECM
14. Back-up light
23. DLC
32. Inhibit switch
6. 4WD control module (if
equipped)
15. 4L/N switch (if equipped)
24. Ignition switch
33. Starting motor
7. Keyless start control module
(if equipped)
16. Transmission fluid temperature
sensor
25. “DOME” fuse
34. CAN driver
8. BCM
17. Shift solenoid valve-A
26. “AT” fuse
35. Meter driver
5A-17 Automatic Transmission/Transaxle:
Component Location
Electronic Shift Control System Components Location
S6JB0A5103001
7
6
5
4
3
20
1
2
9
8
10
11
12
13
14
15
16
17
18
19
I5JB0A510014-02
Automatic Transmission/Transaxle: 5A-18
Diagnostic Information and Procedures
A/T System Check
S6JB0A5104001
Refer to the following items for the details of each step.
1. Engine
6. Transmission warning light (non-
E-OBD)
11. 4L/N low switch (if equipped)
16. Shift solenoid valve-B
2. Transmission
7. MIL
12. Pressure control solenoid valve
17. Valve body assembly
3. BCM
8. Input shaft speed sensor
13. TCC pressure control solenoid
valve
18. Transmission range sensor
4. Selector lever assembly
including “3” position switch
9. Output shaft speed sensor
14. Shift solenoid valve-A
19. ECM
5. P/N mode switch
10. TCM
15. Transmission fluid temperature
sensor
20. AT relay included power
integration No.2 in main fuse box
Step
Action
Yes
No
1
Customer complaint analysis
1) Perform customer complaint analysis.
Was customer complaint analysis performed according to
instruction?
Go to Step 2.
Perform customer
complaint analysis.
2
DTC / Freeze frame data check, record and clearance
1) Check for DTC (including pending DTC).
Is there any DTC(s)?
Print DTC and freeze
frame data or write them
down and clear them by
referring to “DTC
Clearance”.
Go to Step 3.
Go to Step 4.
3
Visual inspection
1) Perform visual inspection.
Is there any faulty condition?
Repair or replace
malfunction part.
Go to Step 11.
Go to Step 5.
4
Visual inspection
1) Perform visual inspection.
Is there any faulty condition?
Repair or replace
malfunction part.
Go to Step 11.
Go to Step 8.
5
Trouble symptom confirmation
1) Confirm trouble symptom.
Is trouble symptom identified?
Go to Step 6.
Go to Step 7.
6
Rechecking and record of DTC / Freeze frame data
1) Recheck for DTC and freeze frame data referring to
Is there any DTC(s)?
Go to Step 9.
Go to Step 8.
7
Rechecking and record of DTC / Freeze frame data
1) Recheck for DTC and freeze frame data referring to
Is there any DTC(s)?
Go to Step 9.
Go to Step 10.
8
A/T Basic Check and A/T Trouble Diagnosis
1) Check and repair according to “A/T Basic Check” and “A/
Are check and repair complete?
Go to Step 11.
Check and repair
malfunction part(s).
Go to Step 11.
9
Troubleshooting for DTC
1) Check and repair according to applicable DTC diag. flow.
Are check and repair complete?
Go to Step 11.
Check and repair
malfunction part(s).
Go to Step 11.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст