Suzuki Grand Vitara JB416 / JB420 / JB419. Manual — part 543
10C-33 Immobilizer Control System: For Diesel Engine Model
Component Location
Immobilizer Control System Components Location
S6JB0AA323001
1
2
3
4
5
6
7
I6JB0AA32001-01
1. ECM
5. Ignition key (non-keyless entry model)
2. Injection warning light (gravity 1 warning light)
6. Transponder
3. Immobilizer control module (ICM)
7. Ignition key (keyless start model)
4. Ignition key (keyless entry model)
Immobilizer Control System: For Diesel Engine Model 10C-34
Diagnostic Information and Procedures
Immobilizer Control System Check
S6JB0AA324001
Diagnostic Trouble Code (DTC) Check
S6JB0AA324002
NOTE
To know how to use SUZUKI scan tool in
detail, refer to its operator’s manual.
1) Turn the ignition switch to OFF position.
2) Connect SUZUKI scan tool to data link connector
(DLC) (1) located under instrument panel at driver’s
seat side.
Special tool
(A): SUZUKI scan tool
3) Turn the ignition switch to ON position.
4) Check if any DTC is stored in ICM according to the
instructions displayed on SUZUKI scan tool.
5) After completing the check, turn ignition switch to
OFF position, and then disconnect SUZUKI scan
tool from DLC.
Step
Action
Yes
No
1
Injection warning light ON check
1) Turn ignition switch to ON position using ignition key.
Does injection warning light (1) come on?
Go to Step 2.
2
Injection warning light flash check
Does injection warning light flash on and off continuously in
Step 1?
Check ICM for DTC
referring to “Diagnostic
Trouble Code (DTC)
Check: For Diesel
Engine Model”.
Go to Step 3.
3
Engine start check
1) Start engine using ignition key.
Does engine start?
Go to step 4.
Go to “Engine and
Emission Control
System Check: For
Diesel Engine Model in
Section 1A”.
4
Injection warning light remain ON check
1) Check if injection warning light remains ON after engine
start.
Does injection warning light remain ON after engine start?
Go to “Injection Warning
Light Remains ON after
Engine Start: For Diesel
Engine Model”.
Immobilizer control
system is in good
condition.
1
I6JB0AA32003-01
(A)
1
I4RS0BA30003-03
10C-35 Immobilizer Control System: For Diesel Engine Model
Diagnostic Trouble Code (DTC) Clearance
S6JB0AA324003
NOTE
To know how to use SUZUKI scan tool in
detail, refer to its operator’s manual.
1) Turn the ignition switch to OFF position,
2) Connect SUZUKI scan tool to data link connector
(DLC) (1) located under instrument panel at driver’s
seat side.
Special tool
(A): SUZUKI scan tool
3) Turn the ignition switch to ON position.
4) Clear DTC(s) according to the instructions displayed
on SUZUKI scan tool.
5) After completing the clearance, turn the ignition
switch to OFF position, and then disconnect SUZUKI
scan tool from DLC.
Diagnostic Trouble Code (DTC) Table
S6JB0AA324004
Immobilizer control module (ICM)
NOTE
• DTC marked with (*) is detected by ECM, transmitted through CAN to ICM and indicated by ICM.
ECM does not indicate (*) marked DTC.
• Immobilizer control module detects DTC B1705 when ignition switch is turned on by using remote
controller of keyless start control system (not using the ignition key). It is not abnormal.
(A)
1
I4RS0BA30003-03
DTC No.
Detecting item
Detecting condition
B1701
Transponder Code Error 1
Inconsistent transponder data from transponder while
registering ignition key
B1702
ECM Communication Error 1
Communication error between ICM and ECM and/or battery
voltage is lower than specified value
B1703
Unregistered Transponder
Transponder code unregistered
B1704
Transponder Code Error 2
Inconsistent transponder data from transponder
B1705
Transponder Response Error
Cannot receive transponder data from transponder
B1706
Immobilizer Antenna Error
Immobilizer antenna faulty
B1707
IMM EEPROM Error
EEPROM in ICM faulty
B1708
ECM Code Error
Verification error between ICM and ECM
B1709
ECM Communication Error 2
Communication error for OBD between ICM and ECM
B1710
Transponder Code Error 3
Inconsistent transponder data from transponder while
registering ignition key
ECM EEPROM Error
EEPROM in ECM faulty
B1712*
Immobilizer Communication Error
Communication error between ICM and ECM
B1713*
Immobilizer Code Error
Verification error between ICM and ECM
B1714*
Unregistered Code
ECM code unregistered
B1716*
Keyless start control module CAN
communication error
Reception error of communication data for keyless start
control module is detected for longer than specified time
continuously.
B1717*
Unregistered keyless start control
module
ECM detects different ID codes registered in ECM and keyless
start control module.
B1718*
Steering lock unit communication
error
• While registering the verification code in the ECM in
immobilizer control system, the keyless start control module
sent a signal to ECM indicating that the ID code could not
be registered.
• The ID code could not be registered in the keyless start
control module or ECM.
Immobilizer Control System: For Diesel Engine Model 10C-36
Scan Tool Data
S6JB0AA324005
Scan Tool Data Definitions
NUMBER OF LEARNT KEY
0 – 4 PCS: The number of the transponder code in the transponder built in the ignition key that is registered with
immobilizer control system
NOTE
A maximum of four transponder codes can be registered with immobilizer control system. Therefore,
the maximal value should be 4.
INPUT YEAR
20**: The year in which the transponder code in the transponder built in the ignition key is registered with immobilizer
control system
INPUT MONTH
1 – 12: The month in which the transponder code in the transponder built in the ignition key is registered with
immobilizer control system
Scan Tool Data
Vehicle Condition
Normal Data
NUMBER OF LEARNT KEY
Ignition switch at ON position
0 – 4
INPUT YEAR
Ignition switch at ON position
2006 or later
INPUT MONTH
Ignition switch at ON position
1 – 12
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст