Suzuki Grand Vitara JB416 / JB420 / JB419. Manual — part 507
9F-15 Security and Locks:
Specifications
Tightening Torque Specifications
S6JB0A9607001
NOTE
The specified tightening torque is also described in the following.
“Front Door Lock Assembly Components”
“Rear Door Lock Assembly Components”
“Rear End Door Lock Assembly Components”
Reference:
For the tightening torque of fastener not specified in this section, refer to “Fastener Information in Section 0A”.
Special Tools and Equipment
Recommended Service Material
S6JB0A9608001
NOTE
Required service material is also described in the following.
“Front Door Lock Assembly Components”
“Rear Door Lock Assembly Components”
Fastening part
Tightening torque
Note
N
⋅m
kgf-m
lb-ft
Door latch screw
5.0
0.5
4.0
Door latch striker screw
10
1.0
7.5
Rear end door latch bolt
5
0.5
4.0
Rear end door striker screw
24
2.4
17.5
Material
SUZUKI recommended product or Specification
Note
Grease
SUZUKI Super Grease A
P/No.: 99000–25011
Seats: 9G-1
Body, Cab and Accessories
Seats
Diagnostic Information and Procedures
Front Seat Heater Symptom Diagnosis (If Equipped)
S6JB0A9704001
Repair Instructions
Front Seat Components
S6JB0A9706001
Condition
Possible cause
Correction / Reference Item
Both seat back and
cushion do not become
hot although seat heater
switch is ON position
Wiring or grounding faulty
Repair.
“IG2 SIG” fuse blown
Replace fuse to check for short.
Seat heater switch faulty
Replace switch.
Seat heater circuit in seat back and/or
seat cushion faulty
Replace heater front back and/or heater front
cushion.
Only seat back does not
become hot although seat
heater switch is ON
position
Wiring faulty
Repair.
Seat heater circuit in seat back and/or
seat cushion faulty
Replace heater front back and/or heater front
cushion.
Only seat cushion does
not become hot although
seat heater switch is ON
position
Wiring faulty
Repair.
Seat heater circuit in seat cushion
Replace heater front cushion.
A
A
A
3
2
4
4
1
9
5
11
5
12
4
4
10
8
7
6
(a)
(b)
(b)
I5JB0A970001-02
1. Seat cushion
5. Seat adjuster
9. Seat mounting bolt
: 23 N
⋅m (2.3 kgf-m, 17.0 lb-ft)
2. Seat back
6. Knob
10. Seat back bolt
: 35 N
⋅m (3.5 kgf-m, 25.5 lb-ft)
3. Headrestraint
7. Side air bag module (if equipped)
11. Seat cushion nut
4. Cover
8. Side air bag harness (if equipped)
12. Seat lifter lever (if equipped)
9G-2 Seats:
Front Seat Removal and Installation
S6JB0A9706002
Removal
1) Disable air bag system referring to “Disabling Air Bag System in Section 8B”.
2) Disconnect seat harness coupler, seat heater coupler and side air bag coupler, if equipped.
3) Remove 4 mounting bolts to remove seat assembly.
4) Disassemble and repair seat as necessary.
Installation
Reverse removal procedure to install front seat.
• Torque to specifications as shown in “Front Seat Components”.
• Enable air bag system referring to “Enabling Air Bag System in Section 8B”.
Front Seat Heater Switch (Driver and Passenger
Side) Inspection (If Equipped)
S6JB0A9706003
1) Confirm that ignition switch is OFF position.
2) Detach gear shift panel from front center console
box.
3) Disconnect seat heater switch coupler.
4) Check for continuity between terminals at each
switch position as shown below. If check result is not
as specified, replace.
Front Seat Heater Wire Inspection (If Equipped)
S6JB0A9706004
1) Confirm that seat heater switch is OFF position.
2) Disconnect coupler of seat heater under the seat
cushion.
3) Measure resistance between terminals as shown
below. If resistance is out of specification, replace
faulty seat cushion and/or seat back including seat
heater.
Seat heater circuit resistance
Seat cushion side [A] (between terminal “B” and
“C”, between terminal “A” and “C”): 4.7 – 5.7
Ω
(at 20
°C, 68 °F)
Seat back side [B] (between terminal “F” and
“D”: 10.7 – 13.1
Ω (at 20 °C, 68 °F)
I5JA01970001-01
1. Heater wire
2. Thermostat
[A]: Seat cushion side
[B]: Seat back side
A
B
C
D
E
F
[A]
[B]
1
1
2
I5JB0A970002-01
Seats: 9G-3
Rear Seat Components
S6JB0A9706005
Rear Seat Removal and Installation
S6JB0A9706006
Removal
1) Remove seat mounting bolt(s) in the bracket.
2) Fold rear seat back and unlock the seat cushion lock to pull forward the seat cushion.
3) Remove seat mounting nuts (bolts) to remove rear seat assembly.
4) Disassemble and repair seat as necessary.
Installation
Reverse removal procedure to install rear seat.
• Torque to specifications in “Rear Seat Components”.
Specifications
Tightening Torque Specifications
S6JB0A9707001
NOTE
The specified tightening torque is also described in the following.
“Front Seat Components”
“Rear Seat Components”
Reference:
For the tightening torque of fastener not specified in this section, refer to “Fastener Information in Section 0A”.
*3
*6
**6
*
*
*4
*4
*5
1
2
3
4
4
*4
(a)
*
(a)
*
(a)
(a)
*
(a)
(a)
(a)
**
I5JB0A970003-01
1. Seat cushion
4. Cover
: 35 N
⋅m (3.5 kgf-m, 25.5 lb-ft)
2. Seat back
5. Rear center seat belt
*: 5 door model
3. Headrestraint
6. Reclining lever
**: 3 door model
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст