Suzuki Grand Vitara JB416 / JB420 / JB419. Manual — part 151
1D-130 Engine Mechanical: For J20 Engine
Special Tools and Equipment
Recommended Service Material
S6JB0A1428001
NOTE
Required service material is also described in the following.
“Timing Chain Cover Components: For J20 Engine”
“2nd Timing Chain and Chain Tensioner Components: For J20 Engine”
“1st Timing Chain and Chain Tensioner Components: For J20 Engine”
“Camshafts, Tappet and Shim Components: For J20 Engine”
“Valves and Cylinder Head Components: For J20 Engine”
“Pistons, Piston Rings, Connecting Rods and Cylinders Components: For J20 Engine”
“Main Bearings, Crankshaft and Cylinder Block Components: For J20 Engine”
Special Tool
S6JB0A1428002
Material
SUZUKI recommended product or Specification
Note
Water tight sealant
SUZUKI Bond No.1207B
P/No.: 99000–31140
SUZUKI Bond No.1207F
P/No.: 99000–31250
09355–35754–600
09367–04002
Hose
3-way joint
09911–97710
09911–97811
Oil seal guide
Oil seal installer
09913–75510
09915–64512
Bearing installer
Compression gauge
09915–64530
09915–67010
Compression gauge hose
Compression gauge
attachment (C)
09915–67311
09916–14510
Vacuum gauge
Valve lifter
Engine Mechanical: For J20 Engine 1D-131
09916–16510
09916–34542
Valve lifter attachment
Reamer handle
09916–37810
09916–38210
Valve guide reamer (6 mm)
Valve guide reamer (11 mm)
09916–46020
09916–57340
Valve guide remover
Valve guide installer
attachment
09916–57350
09916–66510
Valve guide installer handle
(6 mm)
Tappet holder
09916–77310
09916–84511
Piston ring compressor (50-
125 mm)
Forceps
09917–68221
09917–98221
Camshaft pulley holder
Valve guide stem
attachment
09918–08210
09919–28610
Vacuum gauge hose joint
Protector sleeve
09924–17810
09926–58010
Flywheel holder (drive plate
stopper)
Bearing remover attachment
1D-132 Engine Mechanical: For J20 Engine
09944–36011
Steering wheel remover
)
Engine Mechanical: For F9Q Engine 1D-133
For F9Q Engine
Diagnostic Information and Procedures
Compression Check
S6JB0A1434001
Check compression pressure on all 4 cylinders as
follows:
1) Warm up engine to normal operating temperature.
2) Stop engine after warming up.
NOTE
After warming up engine, place transmission
gear shift lever in “Neutral”, and set parking
brake and block drive wheels.
3) Disconnect negative (–) cable at battery.
4) Disconnect ECM connectors (1) and pre-heating unit
connector (2).
5) Remove all glow plugs referring to “Glow Plug
Removal and Installation: For Diesel Engine Model
in Section 1C”.
6) Connect negative (–) cable at battery.
7) Install special tools into glow plug hole.
Special tool
(A): 09912–56540
(B): 09912–57821
(C): 09918–26510
8) Disengage clutch (1) (to lighten starting load on
engine) for M/T vehicle.
1
2
I5JB0B140001-01
(A)
(C)
(B)
I5JB0B140002-01
I4RH0A140057-01
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст