Suzuki Grand Vitara JB416 / JB420 / JB419. Manual — part 510
9I-5 Sun Roof / T-Top / Convertible Top:
Sliding (Sun) Roof Assembly Removal and
Installation
S6JB0A9906008
Removal
1) Remove head lining referring to “Head Lining
Removal and Installation in Section 9H”.
2) Remove sliding roof glass referring to “Sliding (Sun)
Roof Glass Removal and Installation”.
3) Disconnect drain hoses (1) connected to sliding roof
assembly at 4 locations.
4) Disconnect sliding roof motor (1) at coupler (2).
5) Remove 8 nuts (1) and 4 bolts (2), then remove
sliding roof assembly (3).
Installation
For installation, reverse removal procedure, noting the
following points.
• Connect drain hoses (1) to sliding roof assembly at 4
locations. Clamp drain hose by each clamp securely.
• Pass rear drain hose between rib of outlet ventilator
(2).
• Initialize sliding roof position data referring to “How to
reactivate the system to prevent being pinched by the
sunroof” in Sunroof section of Owner’s manual.
• After reinstalling sliding roof assembly, be sure to
make glass adjustment. (Refer to “Sliding (Sun) Roof
Glass Adjustment”.)
5. Deflector
10. Drive cable
1
1
I5JB0A990010-01
1
2
I5JB0A990011-01
1
1
1
1
2
2
3
I5JB0A990012-01
I5JB0A990013-01
Sun Roof / T-Top / Convertible Top: 9I-6
Sliding (Sun) Roof Assembly Disassembly and
Reassembly
S6JB0A9906009
Disassembly
1) Remove sliding roof motor (1).
2) Slide sunshade (1) to full-position.
3) Remove deflector (2) from holder (3) with holding
deflector.
4) Remove No.1 peaces (1) and then pull out sunshade
(2) from guide rails (3).
5) Remove rail stoppers (4) from guide rails.
6) Pull out drip channel (1), panel brackets (2), shoes
(3) and drive cables (4) all together from guide rails.
7) Disassemble drip channel, panel brackets, shoes
and drive cables.
8) Remove guide block (1) and housing covers (2) from
rails.
Reassembly
Reverse disassembly procedure for reassembly, noting
the following.
• Check wear and damage of drive cables and sliding
roof motor gear.
• Apply grease to sliding part.
• Slide shoes (1) to contact guide blocks (2) for
positioning the sliding roof to tilt up position and install
sliding roof motor.
1
I5JB0A990014-01
1
2
3
I5JB0A990015-01
1
2
3
4
I5JB0A990016-01
1
2
3
4
I5JB0A990017-01
1
2
I5JB0A990018-01
1
2
I5JB0A990019-01
9J-1 Hood / Fenders / Doors:
Body, Cab and Accessories
Hood / Fenders / Doors
Repair Instructions
Hood Removal and Installation
S6JB0A9A06001
Removal
CAUTION
!
Place cloth to prevent body from any
damage.
1) Remove hood silencer (4).
2) Disconnect window washer hose (1) from hood.
3) Remove 4 mounting bolts (3) to detach hood (2).
Installation
Reverse removal procedure noting the following.
• Apply sealant to contact face “A” of hood hinge.
“A”: Sealant 99000–31110 (SUZUKI Bond
No.1215)
• Adjust hood lock position if necessary referring to
“Hood Inspection and Adjustment”.
Hood Inspection and Adjustment
S6JB0A9A06002
Inspection
• Check that hood opens and closes smoothly and
properly. Lubricate if necessary.
• Check that hood stops in the secondary latched
position properly (preventing hood from opening
freely) and that hood closes completely in the fully
latched position.
• Adjust hood lock position, if necessary.
Adjustment
Adjust the following point:
• Hood position adjustment.
• Fore-and-aft and right-and-left adjustment.
Adjust hood clearance by loosening hood mounting
bolts. Refer to “Panel Clearance in Section 9K”.
• Vertical adjustment
If only one side (right or left) of hood is not level with
front fender, make it level by tightening or loosening
hood cushion (1).
• Hood lock position adjustment
a. Loosen hood lock bolts.
b. Adjust hood lock height position so the hood is
locked without looseness.
c. Tighten hood latch bolts to specified torque.
Tightening torque
Hood latch bolt (a): 10 N·m (1.0 kgf-m, 7.5 lb-
ft)
d. Make sure the hood is locked smoothly and
securely.
4
2
1
3
“A”
“A”
I5JB0A9A0001-01
I5JB0A9A0002-01
(a)
(a)
I5JB0A9A0003-01
Hood / Fenders / Doors: 9J-2
Front Fender Components
S6JB0A9A06003
Front Fender Removal and Installation
S6JB0A9A06004
Removal
1) Remove splash guard (if equipped) referring to “Splash Guard Removal and Installation (If Equipped) in Section
2) Remove front fender lining.
3) Remove front bumper referring to “Front Bumper Components in Section 9K”.
4) Remove headlight assembly referring to “Headlight Housing Removal and Installation in Section 9B”.
5) Remove cowl top garnishes referring to “Cowl Top Components in Section 9K”
6) Disconnect connector from side turn signal lamp.
7) Remove front fender.
Installation
Reverse removal procedure to install front fender noting the following instruction.
• If paint on fender bolt is peeled off, be sure to apply paint again.
• Adjust panel clearance referring to “Panel Clearance in Section 9K”.
1
3
2
4
I5JB0A9A0004-02
1. Front fender lining
3. Front fender rear pad
2. Front fender
4. Splash guard (if equipped)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст