Suzuki Grand Vitara JB416 / JB420 (ESP model). Manual — part 28
3C-7 Transfer: Motor-Shift Type (Transfer with Shift Actuator)
N (Neutral) Position
When N position is selected from 4H position by turning the transfer switch, the transfer shift control actuator motor
runs and shift cam rotates in the arrow direction “A”. The shift cam shifts the High / Low shift fork in the arrow direction
“B”, and the reduction shift sleeve moves in the arrow direction “B”. Also, the shift cam shifts the differential lock shift
fork in the arrow direction “C”, and the differential lock clutch sleeve also moves in the arrow direction “C”.
The driving force from the transmission is transmitted to the transfer input gear. However, as the reduction shift sleeve
is not engaged with the transfer input gear and low gear, the driving force is not transmitted to the rear output shaft and
front output shaft.
A
C
B
[A]
[B]
1
2
5
4
4
3
5
9
8
6
7
11
12
13
10
I5JB0A332005-01
[A]: Transfer position indicator
2. Center differential lock switch
5. Shift cam
8. Input gear
11. Rear output shaft
[B]: Transfer switch
3. Transfer actuator
6. High / Low shift fork
9. Reduction shift sleeve
12. Drive chain
1. 4L/N switch
4. Shift fork pin
7. Differential lock shift fork
10. Differential lock clutch sleeve
13. Front output shaft
Transfer: Motor-Shift Type (Transfer with Shift Actuator) 3C-8
4L-lock (4WD Low Center Differential Lock) Position
When 4L-lock position is selected from 4H-lock position by turning the transfer switch, the transfer shift control
actuator motor runs and shift cam rotates in the arrow direction “A”. The shift cam shifts the High/Low shift fork in the
arrow direction “B”, and the reduction shift sleeve moves in the arrow direction “B”. Also, the shift cam shifts the
differential lock shift fork in the arrow direction “C”, and the differential lock clutch sleeve also moves in the arrow
direction “C”.
The driving force from the transmission is transmitted from the transfer low gear, through the transfer input gear and
transfer counter gear with the speed reduced. At this time, as the center LSD case and transfer low gear are engaged
via reduction shift sleeve, the driving force is transmitted to the rear output shaft.
The driving force of the rear output shaft makes the front output shaft rotate via the differential lock clutch sleeve as in
the case of 4H-lock position.
A
B
C
[A]
[B]
1
2
5
4
4
3
5
9
8
6
7
11
10
12
13
17
15
18
16
14
19
I5JB0A332006-02
[A]: Transfer position indicator
4. Shift fork pin
9. Reduction shift sleeve
14. Center LSD case
19. Low gear
[B]: Transfer switch
5. Shift cam
10. Differential lock clutch sleeve
15. Front drive shaft
1. 4L/N switch
6. High / Low shift fork
11. Front drive sprocket
16. Counter gear
2. Center differential lock switch
7. Differential lock shift fork
12. Front drive sprocket bush
17. Drive chain
3. Transfer actuator
8. Input gear
13. Rear output shaft
18. Front output shaft
3C-9 Transfer: Motor-Shift Type (Transfer with Shift Actuator)
Input / Output Signal Table of 4WD Control Module
S5JB0E3311008
4WD control module outputs the following signals to actuators, indicators, warning buzzer, according to the transfer
switch operation.
Output signal (to each component parts)
Transfer
shift
actuator
Differential
lock
indicator
4L indicator N indicator
Warning
buzzer
Input signal
Transfer switch
{
{
{
{
{
CPP switch
{
{
{
{
TCM
{
{
{
{
ABS hydraulic unit / control
module
{
{
{
{
{
4L/N switch
{
{
{
Center differential lock switch
{
{
Transfer: Motor-Shift Type (Transfer with Shift Actuator) 3C-10
On-Board Diagnostic System Description
S5JB0E3311009
For 4WD control system, 4WD control module has the following functions.
• When ignition switch is turned ON with engine at stop, differential lock indicator (1), 4L indicator (2) and N indicator
(3) turn on at the same time for 2 seconds in order to check operation of these indicators.
• When 4WD control module detects any malfunction in the following area, differential lock indicator (1), 4L indicator
(2) and N indicator (3) flash continuously and 4WD control module comes into fail-safe mode. For details of fail safe
mode, refer to “Fail-Safe Table: Motor-Shift Type (Transfer with Shift Actuator)”.
– Transfer switch
– Transfer shift actuator motor
– Transfer shift actuator motor position switch
– 4L/N switch
– Center differential lock switch
• DTC can be checked by either one of the following ways.
– DTC can be checked by using SUZUKI scan tool (4) connected to DLC (5).
– If equipped with diagnosis connector, DTC can be displayed on digital display odometer by shorting diagnosis
connector (6).
• When 4WD control module detects any malfunction, 4WD control module will shift automatically transfer to either N
or former position which is in before shifting process began.
DLC (Data Link Connector)
Refer to “Data Link Connector (DLC)” under “On-Board Diagnostic System Description in Section 1A”.
1
2
3
4
5
6
I5JB0A332008-01
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст