JAC S2. Service Manual — part 13
Seat and Safety Belt
Seat and Safety Belt 181
2). Tighten 2 fixed bolts connecting combination meter cover
assembly and dashboard assembly;
2. Install combination meter assembly
3. Install central left side trim panel assembly
4. Install lower guard panel assembly of driver's side
5. Install end cover of dashboard (left)
6. Install central right side trim panel assembly
7. Connect battery negative electrode
8. Close engine compartment cover
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Dashboard
Dashboard 182
Dashboard
I、Summary
(I)Structure Overview
Dashboard Exposed Diagram
1. Dashboard assembly
2. Left end cover of dashboard
3. Right end cover of dashboard
4. Lower guard panel assembly of driver’s side
5. Indoor electrical box cover
6. Combination meter cover assembly
7. Upper jacketing of steering column
8. Lower jacketing of steering column
9. Central right side trim panel assembly
10. Central left side trim panel assembly
11. Decoration panel
12. Radio panel assembly
13. Glove box assembly
14. Exterior cover plate of glove box
15. Glove box lock assembly
16. Central cover plate assembly
(II)Torque Parameter
No.
Item
Torque
(N·m)
1
Fixed bolt of lower guard panel of driver’s side
1.4
2
Fixed bolt of radio panel
1.4
3
Fixed bolt of front part of auxiliary dashboard
1.4
4
Fixed bolt of rear part and left/right side of auxiliary dashboard
5~7
5
Fixed nut of dashboard assembly
5~7
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Dashboard
Dashboard 183
No.
Item
Torque
(N·m)
6
Fixed bolt of dashboard assembly
5~7
7
Fixed nut of A/C main host and beam
5~7
8
Fixed bolt of beam
20
9
Fixed bolt of beam and front wall
20
(III)Maintenance Note
(1). Please observe the handling directions of airbag system strictly, or vehicle damage and personal injury may be caused.
(2). Please dismantle the negative electrode of battery and keep waiting for at least one minutes before removing electric connections,
otherwise damage to the vehicle will be caused.
(3). Please protect the parts with cloth to prevent damage when dismantling and installing the components.
(4). Please wrap the flat-blade of screwdriver with cloth when removing the metal clamp from the trimming
(5). Please guard against damage of the body parts.
(6). Make sure the clamps are fixed into plate hole of the vehicle body securely when installing body trim, and then carefully push
them in.
(7). Two people are needed when a person cannot complete the work of dismantling and installing some components in order to
avoid falling.
(8).Avoid overexertion when dismantling and installing some trims, which may cause deformation of parts.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Dashboard
Dashboard 184
II、Auxiliary Dashboard Assembly
(I)Removal
1. Open engine compartment cover
2. Disconnect battery negative electrode
3. Remove front extension plate assembly
1). Remove 2 expansion buckles in both left and right extension
plate;
2). Disconnect connection of extension plate and auxiliary
dashboard assembly, and take down extension plate;
4. Remove saucer cover plate assembly
1). Pry saucer cover plate assembly in rear part of auxiliary
dashboard;
5. Remove front storage box assembly
1). Pry storage box assembly in front part of auxiliary
dashboard;
2). Disconnect wiring harness connector;
3). Take down front storage box assembly;
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Dashboard
Dashboard 185
6. Remove auxiliary dashboard assembly
1). Remove fixed bolt below lower saucer cover plate;
2). Remove fixed bolt below front storage box assembly;
3). Disconnect connection of transmission operation panel and
auxiliary dashboard;
4). Remove fixed bolt
① in both sides of front part of
auxiliary dashboard and fixed bolt
② in both sides of
middle part of auxiliary dashboard;
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Dashboard
Dashboard 186
5). Pull manual brake rod to maximum angle, and take down
auxiliary dashboard assembly;
(II)Installation
1. Install auxiliary dashboard assembly
1). Pull manual brake rod to maximum angle, and place
auxiliary dashboard assembly to installation position;
2). Tighten fixed bolt
① in both sides of front part of auxiliary
dashboard ;
Tighten torque
1.4N·m
3). Tighten fixed bolt
② in both sides of middle part of
auxiliary dashboard;
Tighten torque
5~7N·m
4). Connect connection of transmission operation panel and
auxiliary dashboard;
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Dashboard
Dashboard 187
5). Tighten fixed bolt below front storage box assembly;
Tighten torque
1.4N·m
6). Tighten fixed bolt below saucer cover plate;
Tighten torque
5~7N·m
2. Install front storage box assembly
1). Connect storage box wiring harness, place storage box to
installation position and tighten buckles;
3. Install saucer cover plate assembly
1). Place saucer cover plate to installation position and tighten
buckles;
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Dashboard
Dashboard 188
4. Install front extension plate assembly
1). Place front extension plate to installation position;
2). Tighten 2 expansion buckles in both sides of left and right
extension plate;
5. Connect battery negative electrode
6. Close engine compartment cover
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Dashboard
Dashboard 189
III、Central Right Side Trim Panel Assembly
(I)Removal
1. Open engine compartment cover
2. Disconnect battery negative electrode
3. Remove central right side trim panel assembly
1). Pry buckles connecting central right side trim panel
assembly and dashboard assembly;
2). Disconnect wiring harness connector, and take down central
right side trim panel assembly;
(II)Installation
1. Install central right side trim panel assembly
1). Connect wiring harness connector;
2). Place central right side trim panel assembly to installation,
and tighten buckles;
2. Connect battery negative electrode
3. Close engine compartment cover
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Dashboard
Dashboard 190
IV、Central Right Side Trim Panel Assembly
(I)Removal
1. Open engine compartment cover
2. Disconnect battery negative electrode
3. Remove central right side trim panel assembly Refer to "Remove central right side trim panel assembly"
4. Remove central right side trim panel assembly
1). Remove 4 fixed bolts of central right side trim panel
assembly and right side air outlet port assembly;
2). Take down right side air outlet port assembly;
3). Remove 6 fixed bolts of central right side trim panel
assembly and central air outlet port assembly;
4). Pry buckles connecting central right side trim panel
assembly and central air outlet port assembly;
5). Take down central right side trim panel assembly;
(II)Installation
1. Install central right side trim panel assembly
1). Connect buckles connecting central right side trim panel
assembly and central air outlet port assembly;
2). Tighten 6 fixed bolts of central right side trim panel
assembly and central air outlet port assembly;
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Dashboard
Dashboard 191
3). Connect buckles connecting central right side trim panel
assembly and right side air outlet port assembly;
4). Tighten 4 fixed bolts of central right side trim panel
assembly and right side air outlet port assembly;
2. Install central right side trim panel assembly
3. Connect battery negative electrode
4. Close engine compartment cover
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Dashboard
Dashboard 192
V、Radio Panel Assembly
(I)Removal
1. Open engine compartment cover
2. Disconnect battery negative electrode
3. Remove central right side trim panel assembly Refer to "Central right side trim panel assembly"
4. Remove radio panel assembly
1). Remove fixed bolt in left/right side of radio panel;
2). Pry buckles of radio panel assembly and dashboard
assembly, and take down radio panel assembly;
(II)Installation
1. Install radio panel assembly
1). Place radio panel assembly to installation position and
tighten buckles;
2). Tighten fixed bolts in left and right side of radio panel
assembly;
Tighten torque
1.4N·m
2. Install central right side trim panel assembly
3. Connect battery negative electrode
4. Close engine compartment cover
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Dashboard
Dashboard 193
VI、Lower Guard Panel Assembly of Driver's Side
(I)Removal
1. Open engine compartment cover
2. Disconnect battery negative electrode
3. Remove end cover of dashboard (left) Refer to ""end cover of dashboard
4. Remove lower guard panel assembly of driver's side
1). Remove left side 2 fixed bolts of lower guard panel
assembly of driver's side;
2). Remove lower part fixed bolt of right side of lower guard
panel assembly of driver's side;
3). Pry buckles connecting lower guard panel assembly of
driver's side and dashboard assembly;
4). In order from left to right, disconnect wiring harness
connector of headlight regulating switch, rearview mirror
regulating switch, light regulating switch, ESP switch;
5). Disconnect connection of OBD diagnosis wiring harness
and lower guard panel of driver’s side;
6). Take down lower guard panel assembly of driver's side
。
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Dashboard
Dashboard 194
(II)Installation
1. Install lower guard panel assembly of driver's side
1). Connect connection of OBD diagnosis wiring harness and
lower guard panel of driver’s side;
2). In order from left to right, connect wiring harness connector
of headlight regulating switch, rearview mirror regulating
switch, light regulating switch, ESP switch;
3). Place lower guard panel of driver’s side to installation
position, and tighten buckles connecting dashboard;
4). Tighten 2 fixed bolts of left side of lower guard panel of
driver’s side;
Tighten torque
1.4N·m
5). Tighten lower part fixed bolt of right side of lower guard
panel assembly of driver's side;
Tighten torque
1.4N·m
2. Install end cover of dashboard (left)
3. Connect battery negative electrode
4. Close engine compartment cover
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Dashboard
Dashboard 195
VII、Central Left Side Trim Panel Assembly
(I)Removal
1. Open engine compartment cover
2. Disconnect battery negative electrode
3. Remove central right side trim panel assembly Refer to "Central right side trim panel assembly"
4. Remove end cover of dashboard (left) Refer to "End cover of dashboard"
5. Remove lower guard panel assembly of driver's side Refer to "Lower guard panel assembly of driver's side"
6. Remove central left side trim panel assembly
1). Remove fixed bolt of central left side trim panel assembly
and dashboard assembly;
2). Pry buckles connecting central left side trim panel assembly
and dashboard assembly, and take down trim panel
assembly;
(II)Installation
1. Install central left side trim panel assembly
1). Place central left side trim panel assembly to installation
position, and tighten buckles;
2). Tighten fixed bolt of trim panel and dashboard assembly;
Tighten torque
1.4N·m
2. Installlower guard panel assembly of driver's side
3. Installend cover of dashboard (left)
4. Installcentral right side trim panel assembly
5. Connect battery negative electrode
6. Close engine compartment cover
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Dashboard
Dashboard 196
VIII、Glove Box Assembly
(I)Removal
1. Remove glove box assembly
1). Open glove box to maximum angle, pull side wall of glove
box and pull out to make stop cylinder slip out;
2). Place glove box flat, and pull glove box from opening port
of dashboard;
(II)Installation
1. Install glove box assembly
1). Place glove box flat, make direction of rotation shaft
opening of glove box is the same with rotation shaft of
glove box, push glove box forward, and make rotation
shaft of glove box into rotation shaft opening of glove
box;
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст