Engine JAC HFC4DA1-2C. Manual — part 68
LT
LT
LT
LT Lighting
Lighting
Lighting
Lighting System
System
System
System
- 62 -
Diagnosis
Diagnosis
Diagnosis
Diagnosis and
and
and
and Testing
Testing
Testing
Testing
Fault
Fault
Fault
Fault diagnosis
diagnosis
diagnosis
diagnosis
1.
Front fog lamp diagnosis
Step
Operation
Yes
No
1
①Turn on the ignition switch and set the headlamp to “position lamp” position.
②Does the front fog lamp lighten when it is turned on?
Go to Step 2.
Check circuit.
2
Does the front fog lamp indicator in combination instrument lighten?
System is normal.
Go to Step 3.
3
①Turn off the fog lamps.
②Turn off the ignition switch.
③Remove the combination instrument.
④Using the multimeter as a ohmmeter, measure the circuit resistance. Is the
reading below 1 Ohm?
Replace
combination
instrument.
Repair fault
circuit.
4
①Check if the system operates normally.
②Does the system operate normally?
System is normal.
Go to Step 1.
LT
LT
LT
LT Lighting
Lighting
Lighting
Lighting System
System
System
System
- 63 -
Diagnosis
Diagnosis
Diagnosis
Diagnosis and
and
and
and Testing
Testing
Testing
Testing
Fault
Fault
Fault
Fault diagnosis
diagnosis
diagnosis
diagnosis
2.
Turn signal indicator diagnosis
Step
Operation
Yes
No
1
Turn on the ignition switch and press the hazard warning lamp switch.
Are front/rear left/right turn signal lamps flickering continuously?
Go to Step 2.
Go to Step 5.
2
Are left/right turn signal indicators flickering continuously?
Go to Step 3.
Check circuit.
3
Turn on the ignition switch and set the turn signal lamp switch to left/right
turning position.
Does left/right turn signal indicator flicker as expected?
Go to Step 4.
Go to Step 6.
4
Turn on the ignition switch and set the turn signal lamp switch to left/right
turning position.
Does left/right turn signal indicator in combination instrument flicker as
expected?
System is normal.
Go to Step 8.
5
Connect the temporary vehicle ground to body control module terminal.
Does the hazard warning lamp flicker as expected?
Hazard warning
lamp operates
normally.
Check body
computer.
6
Use multimeter to measure the voltage of flasher relay.
Does the multimeter indicate the battery voltage?
Replace flasher
relay.
Check circuit.
7
Use multimeter to measure the circuit voltage of turn signal lamp.
Does the multimeter indicate the battery voltage?
Check circuit.
Check circuit.
8
①Turn off the hazard warning lamp.
②Turn off the ignition switch.
③Remove the combination instrument.
④Use the multimeter to measure the circuit resistance. Is the reading below 1
Ohm?
Replace
combination
instrument.
Repair circuit.
9
①Check if the system operates normally.
②Does the system operate normally?
System is normal.
Go to Step 1.
LT
LT
LT
LT Lighting
Lighting
Lighting
Lighting System
System
System
System
- 64 -
Diagnosis
Diagnosis
Diagnosis
Diagnosis and
and
and
and Testing
Testing
Testing
Testing
Fault
Fault
Fault
Fault diagnosis
diagnosis
diagnosis
diagnosis
3.
High-mounted brake lamp failed
Step
Operation
Yes
No
1
Is the fuse blown out?
Go to Step 4.
Go to Step 2.
2
Connect the test lamp with two terminals of brake signal lamp switch. Does
the test lamp lighten?
Go to Step 5.
Go to Step 3.
3
①Connect the test lamp with two terminals of high-mounted brake signal
lamp.
②Depress the brake pedal to check if the test lamp lightens?
Go to Step 6.
Go to Step 7.
4
Replace fuse.
5
Replace brake signal lamp switch.
6
Replace high-mounted brake signal lamp.
7
Repair the circuit of poor contact.
LT
LT
LT
LT Lighting
Lighting
Lighting
Lighting System
System
System
System
- 65 -
Diagnosis
Diagnosis
Diagnosis
Diagnosis and
and
and
and Testing
Testing
Testing
Testing
Fault
Fault
Fault
Fault diagnosis
diagnosis
diagnosis
diagnosis
4.
Ceiling lamp failed
Step
Operation
Yes
No
1
Check if the bulb filament of ceiling lamp is burnt out. Is the filament burnt out?
Go to Step 4.
Go to Step 2.
2
Is the fuse blown out?
Go to Step 5.
Go to Step 3.
3
Connect the test lamp respectively with two terminals of contact switch (left front,
right front, left rear, right rear) and terminals of lighting switch. Does the test lamp
lighten?
Go to Step 6.
Go to Step 7.
4
Replace bulb.
5
Replace fuse.
6
Replace contact switch or lighting switch.
7
Repair the circuit of poor contact.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст